Perlegear PGPILFK1 User manual

Thank you for choosing our product! We strive to
provide the best quality and services for our
customers. Would you kindly share your experience
on Amazon if you are satisfied? Should you have
any issues, please don't hesitate to contact us.
Email：[email protected]
LARGE FULL-MOTION TV WALL MOUNT
PGPILFK1
V1.0

Tools Needed (Not Included)
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware Lists to assure
that all components were received undamaged. Do not use damaged or defective
parts.lf you require replacement parts, contact customer service at
[email protected]
•Not all parts and hardware included will be used.
•Carefully read all instructions before attempting installation.If you do not
understand the instructions or have any concerns or questions, please contact
customer service at [email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly
specified in this instruction. We hereby disclaims any liability for injury or
damage arising from incorrect assembly, incorrect mounting, or incorrect use of
this product.
•DO NOT INSTALL INTO DRYWALL ALONE.
(1PC)
allen wrench 5x5
1PC 4PCS
2PCS
(1PC)
bubble level
Stud
Finder
13/64 in.(5mm)
Wood Drill
25/64in. (10mm)
Socket Wrench 1/2in. (13mm) Socket Wrench Screw
Driver Hammer
Tape
Measure Pencil Drill
Supplied Parts
1
25/64 in.(10mm)
Concrete Drill

M8X20mm
(8PCS)
Supplied Hardware
(4PCS)
M6X10mm
*(2pcs with part 01)
Washers
M8
x4
A2
Hardware for Attaching Wall Plate to Wall
Lag Bolts
M8X65
x4 x4
A1
These anchors are for
concrete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
A3
Wall
Anchor
Hardware for Attaching TV Bracket to TV
Spacers
L10mm
x8
Philips Screws
M6 x 15mm
M6 x 30mm
x4x4
D1 D2
Philips Screws
M8 x 15mm
M8 x 45mm
x4
x4
E1 E2
C1
Spacers
L5mm
x8
C2
Washers
M6
x8
B
Philips Screws
M8 x 65mm
E3
x4
F2F1
(2PCS)(1PC)
05 06
2

Step 1 Measure VESA and Check TV screws
Check TV screws
When attaching brackets to the flat screen, be careful not
to over tighten screws and be sure that screws do not
bottom out in the mounting holes.
Too Short Too Long Correct Correct
Hand thread screws into the threaded
inserts on the back of your TV to
determine which screw diameter ( M6,
or M8) to use.
Width
Height
Measure the distance between the holes located at the back of
your TV (these measures may form the shape of a square, or a
rectangle) and check that these taken measures are within the
VESA(*) range for this wall mount.(*) VESA: International
standard established by the TV manufacturers used to
determine if LCD/LED TVs are compatble with wall mounts.
Manual Only!
3

Step 2
Step 1
Tighten the two screws together.
Step 2
Tighten the two screws together.
02 03
05
05
4

or
or
Step 3 Install TV bracket
For Flat screen TV
For Curved TV
D1 E1
B
D2
B
C1/C2
E2/E3
C1/C2
Manual Only!
Manual Only!
06
06
06
06
5

4A-1 4A-2
Step 4A Wood Stud Option
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall before
continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until
the washers [A2] are pulled firmly against the wall plate
.
X
Step 4 Attach Wall Plate to Wall
For wood stud installation, follow STEP 4A
For concrete installation, follow STEP 4B
Ensure marking at
the center of the
stud. Center line
Use a stud finder (not included) to locate
wood stud. Mark the edge and center
locatons.
05
6

A2 A1
4A-3 4A-4
socket wrench
Step 4B Solid Concrete or Concrete Block Option
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the
washers [A2] are pulled firmly against the wall plate .
WARNING:
Wall
Anchor
A3
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
WARNING:
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the arm assembly/wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
65
Mount the wall plate using 4 sets of
M8X65 lag bolts A1 and washers A2 with a
1/2 in.socket wrench(not included).
Drill 4 pilot holes using a 1/5 in. (5mm)
Wood Drill diameter drill bit.Make sure
the depth is not less than 65mm.
05
7

4B-1 4B-2
4B-3
A3
10mm
Use the hammer to knock
anchors A3 into the wall.
70
Install wall plate using lag bolts A1, washers A2 and anchors A3. Be sure the
anchors [A3] are seated flush with the concrete surface. Tighten the lag bolts
[A1] only until the washers [A2] are pulled firmly against the wall plate[05] . DO
NOT over-tighten the lag bolts [A1].
Position the wall plate at your desired
height, level the wall plate and mark the
pilot hole locations.
Drill 4 pilot holes using a 25/64
in.(10mm) diameter drill bit.Make sure the
depth is not less than 70mm.
05
A2
05
8

Step 5
Step 6 Level Adjustment
Hang your TV to the Brackets and lock it.
1
2
If needed,the TV can be leveled.
Level the TV
Iocking
9