Perlegear PGUE1 User manual

V1.0
TV Wall Mount Extension Bracket
Instruction Manual
Thank you for choosing this Perlegear product! At Perlegear we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us.
Technical Support:
1-800-456-5231 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected](US)
Model: PGUE1

Weight Restrictions
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
within the maximum weights indicated. Use with
products heavier than the maximum weights
indicated may result in failure of the mount and
its accessories, causing possible damage and
or injury.
WARNING
If your TV (including accessories)
plus TV wall mount weight more,
this product is NOT compatible.
132 lbs.
(60 kg)
V1.0
IMPORTANT SAFETY INFORMATION
CAUTION
DO NOT install into
drywall alone!
Before getting started, please make sure this extension bracket
is perfect for you!
12in.<Wall Plate Width<16in. 16in.<Wood Stud Spacing≤24in.
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
Technical Support line at 1-800-456-5231 or customer service at
[email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual.
• Do not exceed weight capacity. We are not liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and mount
combined.
01 02 03 04 05

Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
Technical Support line at 1-800-456-5231 or customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Note: The lag screw is shown in accordance with the actual size
Washer
φ8.2xφ20x2.0
x4
A2
7/32 in.(5.5 mm)
Wood Drill
1/2 in.(13mm)
Socket Wrench Level
Tools Needed (Not lncluded)
Awl
Stud Finder Tape Measure Pencil Drill
Lag Screw
ST8x65mm
x4
A1
Extension Bracket
01 x2
Washer
A x4
Nut
B x4
01 02 03 04 05

1/2 in.(13mm)
Socket Wrench
[Not Included]
Step 1 Connect the TV Wall Mount (Not Included) to the
Extension Bracket
Connect the TV wall
mount (not Included) to
the extension bracket by
washer [A] and nut [B].
Step 2
●Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2]
are pulled firmly against the extension bracket [01].
● Ensure the extension bracket [01] is securely fastened to the wall before
continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Install the Extension Bracket on Wood Stud
Fully unfold the extension bracket and make
sure the two halves are flushed with each
other.
01
B
A
B
A
Note:
Do not firmly tighten
the nuts to keep the
sliding function.
01 02 03 04 05

2A-1
Use a stud finder (not included) to
locate wood studs or use an awl
(not included) to verify the edges.
Mark the edge and center locations.
Awl
(Not lncluded)
24 in.(610mm)
16 in.(406mm)16 in.(406mm)
2A-2
2A-3
Drill 4 pilot holes using a
7/32 in.(5.5mm) diameter drill
bit. Make sure the depth is not
less than 2 9/16 in.(65 mm).
Position the extension bracket [01]
at your desired height and line up
the holes with your stud center line.
Level the extension bracket [01]
and mark the holes.
HEAVY! You may need
assistance with this step.
7/32 in.(ø5.5 mm)
2 9/16 in.(65 mm)
2A-4
Install the extension bracket [01]
using lag screws [A1] and
washers [A2]. Tighten the lag
screws [A1] only until the
washers [A2] are pulled firmly
against the extension bracket [01].
1/2 in.(13mm)
Socket Wrench
[Not Included]
HEAVY! You may
need assistance
with this step.
A2 A1
01 02 03 04 05

B
TightenTighten
1/2 in.(13mm)
Socket Wrench
[Not Included]
Step 3 Horizontal Sliding Adjustment
To better position your mount and TV on your wall, the mount can be
horizontally slided from side to side. After sliding the wall mount at at
desired position, firmly tighten four nuts [B].
01 02 03 04 05

Thank you again for
choosing this Perlegear product!
All of us at Perlegear do appreciate your product purchase. We hope that you
are as happy with your product as we designing and manufacturing it for you.
We strive to provide you with the best quality products and services in the
industry. If you have any questions please don't hesitate to contact us.
Technical Support:
1-800-456-5231 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected](US)