Perlegear PGTVS29 User manual

TABLETOP TV STAND
INSTRUCTION MANUAL Rev01
Thank you for choosing this Perlegear product. We strive to provide you with the best
quality products and service in the industry. If you have any installation questions or issues
with the product, please contact us at the number below.
1-800-456-5231 (US/CA) Mon–Fri, 8am–8pm (CST)
44-808-196-4165 (UK) Mon–Fri, 2pm–10pm (UTC)
[e-mail]
www.perlegear.com
PGTVS29
MODEL

K
Q
S
V1
V2
W
Knob
Cable Clip
Bolt
Plastic Washer
Steel Washer
Foot Pad
01
02a
02b
03
04
Tempered Glass Base
End Cap
Support Pillar
Faceplate
Plastic Cover
01
W
02b
03
04
Q
Q
V1
V2
S
K
02a
02

Tools Needed
(NOT Included)
2
3
4
1
BEFORE GETTING STARTED, LET'S MAKE SURE THIS STAND IS
COMPATIBLE.
Check VESA Pattern
Compatibility
Check Max Load
Important Safety
Information
• Please carefully read all instructions before attempting installation.
If you do not understand the instructions or if you have any questions
or concerns, please contact our Technical Support line as listed above
or Customer Service at [e-mail].
• Not all hardware included in this package will be used.
DO NOT exceed the Max load
indicated. Use with products heavier
than the Max load may result in
failure of the mount, which could
cause damage or injury.
WARNING
If your TV weighs more,
this stand is NOT compatible.
Minimum:
50 x 50mm (2 x 2″)
Maximum:
100 x 100mm (3.9 x 3.9″)
Measurement Conversion
50mm = 2″
75mm = 3″
100mm = 3.9″
44 lbs
(20kg)
3.9″
100mm
Max:
3.9″
100mm
Max:
CAUTION: Avoid potential injuries and property damage!
• Do not use this product for any purpose that is NOT explicitly
specified in this manual. Do not exceed the Max load. We're not liable
for damage or injury caused by incorrect assembly, improper mount-
ing, or inappropriate use.
• Before starting assembly, check all parts are included and undam-
aged. Do not use damaged or defective parts. If you require replace-
ment parts, please contact our Technical Support line as listed above
or Customer Service at [e-mail].
WARNING: This product contains small parts that may pose a
choking hazard.
If this stand is not compatible, please contact our Technical Support
line as listed above or Customer Service at [e-mail].
SAVE THESE INSTRUCTIONS.
Phillips Screwdriver
3⁄8″ (10mm)
Wrench
03

SUPPLIED PARTS AND HARDWARE
Washer Spacer
M4
TV Bolt
L2.5mm
Ex 4
M6
A2 x 4
M4/M5
A1 x 4
M4 x 30mm
B2 x 4
M4 x 12mm
B1 x 4
L10mm
Fx 8
M5
M6
M6 x 15mm
D1 x 4
NOTE: The washers, spacers, and bolts shown above are displayed in accordance with actual size.
Faceplate
03 x 1
Plastic Washer
V1 x 3
Steel Washer
V2 x 3
Foot Pad
Wx 4
Cable Clip
Qx 2
Plastic Cover
04 x 1
Tempered Glass Base
01 x 1
Support Pillar
02b x 1
End Cap
02a x 1
Bolt
Sx 3
Knob
Kx 1
5/32″ (4mm)
Allen Key
K1 x 1
M5 x 25mm
C2 x 4
M5 x 16mm
C1 x 4
M6 x 25mm
D2 x 4
04

STEP 1 ATTACHING THE FACEPLATE TO YOUR TV
INSTALLATION
Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4,
M5 or M6) to use. We recommend screwing in at least five turns. Do not turn past the bottom of
the hole.
SELECT TV BOLTS
Only one bolt size fits your TV.
M6M4 M5
SPACER AND BOLT CONFIGURATIONS
Bump
See Option C
Cables
See Option D
Recessed Holes
See Option E
Curved Back TV
See Option B
Flat Back TV
See Option A
Alternative Spacer
Combinations
05

CHOOSE THE COMBINATION THAT APPLIES TO YOUR VESA HOLE PATTERN
ATTACH THE FACEPLATE TO YOUR TV
CAUTION:
• The lever should be
positioned toward the
top of the TV.
50 x 50mm (2 x 2″)
75 x 75mm (3 x 3″)
100 x 100mm (3.9 x 3.9″)
1
2
3
1 1
2 2
2
1 1
2
33
33
OPTION A: FOR FLAT BACK TVS
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
Add spacers, if needed, to fit the bolt length and TV back.
Washer A1 | A2
TV Bolt B1 | C1 | D1
Spacer E
(optional)
06

D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
OPTION B: FOR CURVED BACK TVS
Spacers must be tall enough so that the curved back of the TV does not interfere with the
mounting plate.
OPTION C: FOR TVS WITH A BUMP
The faceplate must be flush on the bump and leveled by spacers on the gap.
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
Washer A1 | A2
Spacer E | F
TV Bolt B2 | C2 | D2
Washer A1 | A2
Spacer E
(optional)
TV Bolt B1 | C1 | D1
Washer A1 | A2
Spacer E | F
TV Bolt B2 | C2 | D2
Alternative Spacer
Combinations
Alternative Spacer
Combinations
07

OPTION D: FOR TVS WITH PROTRUDING CABLES
Use spacers to create extra space between the TV and faceplate.
OPTION E: FOR TVS WITH RECESSED HOLES
Spacers need to fill in the recessed holes on the back of the TV, while keeping the faceplate as
close to the TV as possible.
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
Washer A1 | A2
Spacer E | F
TV Bolt B2 | C2 | D2
03
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
Washer A1 | A2
TV Bolt B2 | C2 | D2
Spacer E | F
03
Alternative Spacer
Combinations
Alternative Spacer
Combinations
08

Attach the foot pads [W] to the matte side of the tempered glass base [01].
TIP: Leave a small gap between the edge of the glass and the foot pads.
STEP 2 CONNECTING THE SUPPORT PILLAR TO THE BASE
1
W
Secure the support pillar [02b] to the tempered glass base [01].
2
(Plastic Washer)(Plastic Washer)
K1
01
04
02b
01
DesktopDesktop
01
02b
S
V2
V1
(Steel Washer)(Steel Washer)
K1
5/32″ (4mm)
Allen Key
09

3
The support pillar has five height options. Choose the best height position for your TV
before moving on to attach your TV to the pillar.
1
STEP 3
ATTACHING THE TV TO THE SUPPORT PILLAR
Highest
TV position
Lowest
TV position
Highest TV position Lowest TV position
Examples
02b
02a
10