Perma child safety 2742 User manual

#2742 White
#2769 Warm Black
Extra Tall & Wide
Superior Swing Gate
INSTRUCTION MANUAL
This product complies with safety standard ASTM F1004-21 & EN1930:2011
IMPORTANT! READ AND FOLLOW
THESE INSTRUCTIONS
CAREFULLY AND KEEP
FOR FUTURE REFERENCE.
INSTALLATION VIDEO
FITS OPENINGS
91cm
(36”)
82cm - 142cm
(32.3” - 55.9”)
TALL

TABLE OF CONTENTS
SAFETY INFORMATION
General
Maintenance
Warnings
Mountings / Tools Required
WHAT’S IN THE BOX
Parts
INSTALLATION
Gate Placement
Assembling Gate Panels
Hinge Side Mounting
Locking Side Mounting
Hinge Assembly
Gate Adjustment
OPERATION
How to Operate
Cleaning Instructions
SUPPORT
Warranty Certificate
Warranty Card
After Sales Support
03
03
04-05
06-07
08-09
10
11-13
14
15-16
16-17
18 -19
20
21
22
23
23
02

Read this instruction manual carefully and keep it in a safe place for
future reference.
The correct use and maintenance of this product is essential.
Regularly check that the product is functioning correctly, lubricate hinges
and moving components. Tighten and adjust mounts to ensure secure
smooth operation. Inspect all components regularly and stop using if any
component is damaged or missing.
Refer to pages 20 & 21 for operation and cleaning instructions.
GENERAL
MAINTENANCE
SAFETY INFORMATION
03

• Adult assembly required.
• This gate is for domestic use only.
• The gate must not be fitted across windows.
• Always check that the gate is correctly closed.
• Danger to older children if climbing over the product.
• Do not use gate if any components are damaged, missing or
disassembled.
• If the gate is used at the top of the stairs, it should not be positioned
below the top level. Always have the gate open away from the stairs.
Keep 15cm (6”) gap between gate and the top step.
• If the gate is used at the bottom of the stairs, it should be positioned at
the front of the lowest tread possible.
• NEVER use to keep child away from pool.
• Never leave child unattended when using this product.
• Never use with a child able to climb over or dislodge/ open the gate
enclosure.
• Never install this product on glass doors. Always install this product
against reliable doors or walls.
• Incorrect installation can be dangerous.
04
WARNING

• Use only with the locking/ latching mechanism securely engaged.
• Make sure the product is installed as per the installation guides
placement.
• Regularly check that the gate is properly installed and secure.
• Any additional or replacement parts should be obtained from
after sales support.
• Gate must be fitted between rigid surfaces such as plaster board,
timber or hard wall.
• Do not put any goods which can be grabbed by children or pets near
this product to prevent injury.
• Before using this product, carefully inspect for any loose parts and
whether any parts need to be tightened.
• Children have died or been seriously injured when gates/ enclosures
are not securely installed.
• To prevent serious injury or death, securely install gate and use
according to manufacturer’s instructions.
• ALWAYS install and use gates/enclosures as directed, using all
required parts.
• This safety barrier has a manual closing system.
• This product is intended for use with children from 6 to 24 months or
small to medium pets.
05
WARNING

SAFETY INFORMATION
Gate must be installed in a structurally sound opening. Ensure mounting
surface (wall, door, stair posts, etc.) is strong, rigid and has an even
surface.
Note: If the safety barrier is used at the top of the stairs, it should not be
positioned below the top level. If the safety barrier is used at the bottom of
the stairs, it should be positioned at the front of the lowest tread possible.
This gate must only be fixed to a solid and secure surface. If unsure, check
with a qualified builder or trades person that the installation you intend is
suitable and safe within the chosen location.
MOUNTINGS
TOOLS REQUIRED
PENCIL
DRILL
PHILLIPS HEAD
SCREW DRIVER
06

SAFETY INFORMATION
FOR INSTALLATION
Wood Screws
Anchor
07
FOR INSTALLATION
Wood Screws
1. Drill 5mm (3/16”)
Pilot Hole
2. Clear Hole 4. Tighten slowly3. Insert Anchor & Tap
Select the appropriate fixing method from the list below.
Locate the wood stud and follow the wood mounting instructions.
Do not mount into dry wall without additional support.
HARD WALL MOUNTING BRICK / CONCRETE
1. Drill 2mm (5/65”)
Pilot Hole
2. Clear Hole 4. Tighten slowly3. Insert Screw
WOOD MOUNTING
1. Drill 2mm (3/32”)
Pilot Hole
2. Insert Screw Do not mount without
additional support
3. Tighten slowly
DRY WALL MOUNTING

WHAT’S IN THE BOX
PARTS
08
2 x Gate Panels
2xTop Gate Connectors 2 x Bottom Gate Connectors
1 x Top Catch Bracket 1 x Bottom Catch Bracket
1 x Stop Pin
(Pre-installed)

WHAT’S IN THE BOX
09
1 x Hinge Side Installation Guide
1 x Locking Side Installation Guide
2 x Hinge Cap
2 x Spring Cover
2 x Springs
2 x Hinge Bolt
2 x Hinge Bottom
2xAdjustable Catch Bolt 1 x Wrench 8 x Screws
HINGE ASSEMBLY

Swing Gate Placement
Suitable placement of Swing Gate.
Bottom of Stairs
If the gate must be installed
on stairs, position it towards
the front of the lowest step.
Top of Stairs
The gate must be installed on
the top step or landing and
only open away from the
stairs (see page 15 for Swing
Direction Control). DO NOT
install gate in the middle of
the stairs as it may become
a hazard.
Hallways & Doorways
Suitable for extra wide
Hallways & Doorways.
INSTALLATION
10

Correct Incorrect
INSTALLATION
Step 1. Assembling Gate Panels
1. Adjust panels until gate is approximately the correct width.
Panels should fit without any distance between rails or bars.
11

“CLICK”
“CLICK”
2. Secure Gate Panels together using Top and Bottom
gate connectors.
INSTALLATION
12

NOTE: Final Bolt adjustments
will be made later.
INSTALLATION
3. Screw Hinge Bolts into
top and bottom rail of
one gate panel.
Extend bolts equally.
4. Screw Adjustable Catch
Bolts into top and bottom
rails of second gate panel.
Extend bolts equally.
13

INSTALLATION
Step 2. Hinge Side Mounting
1. Align template against mounting surface with the end
marked “FLOOR” even with the floor.
Mark screw hole positions.
2. Mount Upper and Lower Hinge Bottoms, secure in place
with only bottom Screw.
14
TOP BOTTOM

LEFT SIDE
OPENING
BOTH SIDE
OPENING
RIGHT SIDE
OPENING
INSTALLATION
15
Step 3. Locking Side Mounting
1. Align template against mounting surface with the end
marked “FLOOR” even with the floor.
Mark screw hole positions.
2. Determine which direction gate should open. For the top
of stairways, gate should never open out over stairs. Insert
Stop Pin from behind in holes of Bottom Catch Bracket
opposite desired opening direction.

3. Using the Screws provided mount Top and Bottom Catch
Brackets in screw hole positions.
INSTALLATION
16
Step 5. Hinge Assembly
1. Center gate in opening. Adjust Upper and Lower Hinge
Bolts, so post fits into bolt eyelet. Place Spring and Spring
Cover on upper and lower hinge posts. Place Hinge Cap on
Hinge and push down until it locks in position. Screw in place.

Hinge Side
Min. 2.5cm (1”)
Max. 6cm (2”)
Locking Side
Min. 3cm (1.2”)
Max. 6cm (2”)
IMPORTANT
Leave at least 3cm (1.2”) to maximum 6cm (2”) gap on
bolts for the locking side. Minimum 2.5cm (1”) to maximum
6cm (2”) gap on bolts for the hinge side. Make sure bolts
extended equally on both sides.
INSTALLATION
17

NOTE: If gate is not at correct width, it may
be necessary to remove gate and readjust the
panels. (Refer back to Step.1 Assembling
Gate Panels)
Check gate opens and closes smoothly.
18
INSTALLATION
Step 6. Gate Adjustment
1. Adjust Catch Bolts until secure in both Top and Bottom
Catch Brackets. Top Bolt must lock under locking latch
when in the closed position.

19
CAUTION: Do not over-tighten lock nuts,
over-tightening may damage thread.
INSTALLATION
2. When satisfied with gate width, tighten all Screws with a
Phillips head screw driver. With the Wrench, tighten all lock
nuts towards the gate.

Opening & Closing
To open gate, press down on Top Catch Bracket with
thumb. Lift gate out of brackets.
To close and lock gate, Top Adjustable Catch Bolt must
rest in Top Catch Bracket and Bottom Adjustable Catch
Bolt must rest in Bottom Catch Bracket.
Locking Indicator
Locked Position:
Children are unable to open
the gate in this position
Unlocked Position:
Children are able to open
the gate in this position.
OPERATION
HOW TO OPERATE
NOTE: Always check gate
is properly closed and
secure at all times.
20