Perrin & Rowe 4799 Operation manual

• 4799
The Country Kitchen Collection
Installation & User Guide
Perrin & Rowe products are manufactured in the UK, using the latest
technology and built to the highest quality standards.
We would like to thank you for purchasing a Perrin & Rowe product and
take this opportunity to invite you to look at other luxury products by us.
Please contact us to receive our latest catalogue.
Perrin & Rowe is a registered trademark of Avilion Ltd. 904799 Issue 1
Temp Range:
Max 85°C/185°F
Recommended
Working Pressure:
Min 1bar/15psi
Max 5bar/75psi
* Where indicated please specify colour
SPARES COUNTRY POT FILLER
• 4798
9.13249
9.13249
9.25552
9.15799*
9.18799*
9.54799 - SERVICE KIT
Contains all seals,
fixing and bearing
rings.
9.12799*
O64
9.18798
9.51798*
100
415
255
100
1/2" BSP
O7/8"
HOLE
Full Extended Reach 605
9.12798*
SPARE PARTS & SERVICE
Phone: [phone]
Fax: [phone]
[e-mail]
www.perrinandrowe.co.uk
GUARANTEE & LIABILITY
Your Perrin & Rowe product has been manufactured to exacting standards. However, in the unlikely event that
you should experience any defect, the following guarantees will apply:
Your Perrin & Rowe product is guaranteed against any mechanical defect within five years of the date of
purchase. Should a fault occur; a free replacement part will be issued. In the event that this does not resolve
the defect, a replacement product will be supplied.
The surface finish of Perrin & Rowe products are guaranteed for one year from the date of purchase. This is
provided our care and maintenance instructions have been followed and that no scouring or aggressive cleaning
agents have been used.
This does not affect your statutory rights.
For full terms and conditions please contact Perrin & Rowe.

Congratulations on the purchase of your Perrin & Rowe Kitchen Product. Correctly installed and with sensible care,
this product will give you many years of trouble free service.
The Country Kitchen Collection
Installation & User Guide
IMPORTANT INFORMATION
Please note: Do not disassemble the unit for installation.
Before you proceed... We recommend you engage the services of a registered plumber to install
this product.
For ease of possible future servicing, we also recommend the fitting of conveniently placed
isolating valves.
In addition to the guide below it is essential that the written information overleaf is carefully
read and understood.
Please note: If the Pot Filler is not in use or left unsupervised, ensure both levers are in the
closed position.
Preparation Check Box for Installer
Flush the plumbing system before
installing the Kitchen product.
1
2
CARE & MAINTENANCE
Wipe down after use to avoid water spotting and mineral build up.
Occasional cleaning with warm soapy water, followed by a polish with a soft cloth is all that is required to keep the
plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the pot filler. Do not use any
products with ammonia bleach or limescale remover. You will damage the plated finish and void your
guarantee.
BEFORE USE
• Carefully check the installation for leaks.
• If further building work is to be carried out in the vicinity, cover the pot filler with a plastic bag to avoid
damaging the finish.
• Please ensure that the installation complies with local plumbing codes.
When installing on internal walls
appropriate reinforcement may be
required for sufficient strength.
Screw the BSP inlet feed onto the inlet shank using a
1/2" AF Allen Key. Screw backnut onto inlet shank
for reinforcement.
Once the BSP connector is fixed to wall surface,
position the rosette onto the valve body. Ensure
all O Rings are correctly installed as shown in
diagrams.
WATER
IN
½" BSP INLET
FEED
(SUPPLIED)
Position plumbing to suit installation, taking into
account the suitable height and reach.
Remove 1/2" BSP wall connector from pot filler
assembly.
Ensure black rubber O Rings are fitted at
positions A and B on the BSP inlet feed. Check
they are undamaged and free from any debris.
Ensure all connections are firmly tightened.
Keeping the rosette loose on the valve body install
the pot filler onto the wall connector and securely fix
with the 2 concealed fixing screws. Ensuring that
the srews are secured firmly into the keyway.
Slide the rosette over the concealed fixing
screws until it is flush with mounting
surface.
1/2" INLET SHANK
Ensure the mounting
surface is level.
ROSETTE
A
IMPORTANT: Ensure fixing screws are fully
tightened using maximum leverage.
B
WALL FIXING FLANGE
Once tightened adjust so that the wall fixing flange is
level. Place a spirit level onto the flat of the wall fixing
flange.
Adjust the depth of the fixing flange accordingly.
Secure the wall fixing flange to the wall with the
supplied screws. Alternatively, please use the
correct fixing to suit the installation.
WATER
IN
BACKNUT