Pestill PSUVELBGZPA User manual

UV ELECTRIC BUG ZAPPER
PSUVELBGZPA

Read instructions in this guide before using this product. Retain this guide for future
reference.
• This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
product in a safe way by the person responsible for their safety, and understand
the hazards involved.
• Before using this product, ensure the product voltage and household voltage
match.
• Do not disassemble or modify this product in any way.
• To avoid fire hazard or possible explosion, do not place this product near or into a
fire.
• During operation, do not stare directly at the UV light for an extended time and
always keep the UV light at a safe distance from your body.
• While in operation, this product should be in a place out of the reach of children.
• Do not touch or place any metallic objects in the product.
• If the high voltage grid or any electrical component shows signs of damage, cease
use immediately and contact help.Kogan.com for support.
• If the product is not used for an extended period, unplug it and put it in a safe
place.
• If the product is intended for outdoor use, to avoid damage, keep it in a location
away from rain.
• Do not use in an environment where it will be exposed to flammable vapours and or
combustible particles.
• If using with an extension cord, to avoid protentional damage, ensure the cord is
not exposed to water or any other liquids.
DANGER: HIGH VOLTAGE
Warning: Do not immerse this product in water or
other liquids.
SAFETY & WARNINGS

OVERVIEW
Ring
To p cover
Tu b e
High
voltage grid
Protection grid
Storage tray

Replacing the Bulb
1. Remove the storage tray from the
bottom of the zapper.
2. Remove the screw.
3. Remove the bottom cover.
ASSEMBLY

4. Remove the damaged bulb.
Note:Ensure the bulb has cooled down
before handling it.
5. Insert the bulb, ensuring the four
terminals on the bulb line up with the
four holes in the zapper.
6. Replace the bottom cover and secure it
in place with the screw.

Turning On & Off
• Connect the zapper to a power outlet, the UV light will turn on, the zapper is ready
for operation.
• To t u r n o f f t h e z a p p e r, disconnect it from the power outlet.
• For best results keep the machine running for more than 12 hours.
365nm (nano meter) Light
This product uses fluorescent lamps, producing 365nm light to lure mosquitoes and other
flying insects. When an insect comes in contact with the high voltage grid they will be
exterminated.
OPERATION
High voltage grid

• Before cleaning, switch off and disconnect the product from the power outlet and
wait for 10 seconds before proceeding.
• Use a brush to remove dead insects from the fins on the high voltage grid.
• This product will need to be cleaned at least once every two.
• For more stubborn debris, wipe with a soft cloth with a small amount of water-
diluted mild detergent. Ensure the product is thoroughly dried before plugging it
back in a power outlet.
• Do not use alcohol-based spray cleaners to clean the surface.
Clean the Storage Tray
• Remove the storage tray by rotating in a counter-clockwise direction.
• Clean it with water then wipe it dry.
• Install the tray and ensure it locks back in position with a “click".
CLEANING & CARE

Rated Voltage
220-240V
Rated Power
18W
Rated Frequency
50-60Hz
Net Weight
1 kg
Gross Weight
1.45kg
Dimensions
181x161x336mm
Waterproof Rating
IPX4
SPECIFICATIONS

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com