Rentokil Lumnia Slim US User manual

Lumnia Slim US - Instruction Manual
This manual is based on the latest information and is provided subject to
alteration. We reserve the right to change the construction and/or configuration
of the product and versions at any time without obligation.
All rights reserved. No part of this document may be reproduced, stored in a database or any other retrieval
system, or published, in any form or way, electronically, mechanically, digitally per photo print or microfilm
or any other way without written permission from the author.

IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using electric appliances, basic
precautions should always be followed, including the following:
a. Read all the instructions before using the appliance.
b. To reduce the risk of injury, close supervision is necessary
when an appliance is used near children.
c. Do not contact moving parts.
d. Only use attachments recommended or sold by the
manufacturer.
e. Do not use outdoors.
f. To disconnect the appliance:
− Plug detachable supply unit directly into receptacle - do not
use an extension cord.
− Unplug detachable supply unit before plugging or
unplugging appliance.
− Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
− Unplug from outlet when not in use and before servicing or
cleaning.
− Do not operate any appliance with a damaged cord or
plug, or after the appliance malfunctions or is dropped or
damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair, or
electrical or mechanical adjustment.
g. Always unplug before replacing the lamp. Replace lamp with
the same type UV-LED Lamp: 304816
h. This appliance is provided with double insulation. Use only
identical replacement parts. See instructions for Servicing of
Double-Insulated Appliances.
CAUTION - Risk of UV exposure. Ensure the product is installed
such that no continous human activity is likely to be performed
within 3’3” (1M) distance of the unit while illuminated.
SAVE THESE INSTRUCTIONS
1. Safety

The lamps in this unit produce ultraviolet (UV) light, which can
cause skin or eye damage if viewed directly for a long period.
Only fit the correct type of UV lamps in the unit.
The unit shall be installed and serviced by individuals with
appropriate qualifications and/or experience in accordance
with national regulations in the country of operation and
installation.
Disconnection from the mains is provided by means of a
supply cord fitted by a plug. Protect the mains cable from
damage. If the mains cable is damaged, do not use the unit.
The cable must be replaced by the manufacturer, its service
agent, or similar qualified persons.
Do not insert foreign objects into the unit.
Do not use an extension cable with this unit.
Only personnel with appropriate skills and training must install
or service this unit.
Do not install this unit in areas where dangerous
concentrations of inflammable or explosive substances may
be present in the air.
Only install this product indoors in a dry location that is
shielded from direct sunlight. Do not install the unit in a barn,
stable, or similar location.
Install the cable such a way to prevent the exposition of the
cable to UV radiation from UV Lamps
Children or personnel with reduced physical, sensory or
mental capabilities, or personnel who lack experience or
knowledge, must not use this unit, unless they are supervised
by a person responsible for their safety.Children must not
play with this unit. The appliance is to be kept out of reach
of children. Do not place or fit directly above food handling,
preparation or manufacturing areas. Do not place or fit directly
above food handling, preparation or manufacturing areas.
Users can perform the maintenance tasks described in this
document. Users must not perform any other repairs or
maintenance.
Warning
Caution
Attention
WARNING Skin or eye damage
may result from directly viewing
the light produced by the lamp in
this apparatus. To safeguard always
ensure installation manual and
manufacturers recommendations
are followed.
CAUTION Risk of UV exposure. Ensure product
is installed to ensure no person is likely to be
within 3’3” feet of the unit while illuminated.
AVERTISSEMENT Observer la lumière produite
par la lampe de cet appareil sans protection peut
causer des dommages cutanés ou oculaires.
Pour des raisons de sécurité, veillez au respect
des consignes du manuel d’installation et des
recommandations du fabricant.
ATTENTION Risque d’exposition UV. Veillez à ce
que le produit soit installé de manière à ce que
personne ne se trouve à moins de 3’3” feet de
celui-ci tandis qu’il est allumé.
1. Safety
SAVE THESE INSTRUCTIONS

3. Equipment for Installation
A3 drilling template – Supplied in Box
Screw Fix Kit – Supplied In Box
Spirit Level advised – Not Supplied
Power Drill - Not Supplied
Masonry Drill Bit Ø15/64”(6mm) - Not Supplied
Phillips Screw Driver PH2 – Not supplied
In the Box:
AEquipment Required for Install B
1. Lumnia Slim Black: 305065
Lumnia Slim White: 304977
Also includes x1 UV-LED Lamp 304816
2. Drilling Template
3. Screw Fix Kit
4. Instruction Manual
5. Quickstart Guide
6. Glue Board (Black) 305057
7. Internal Packaging
8. Outer Box
9. Mains Plug, Cable and Pin Adapters
10. Extension Cable
1
2
3
4
8
5
9
7
7
6
6
10
2. Introduction
The Lumnia Slim unit uses one ultra-violet LED driven lamp that attracts flying insects,
which are then captured on a replaceable glue board. The Slim product is a glue board
monitoring device.
While unpacking, check for any signs of shipment damage and, if found, notify both
transporter and supplier in writing as soon as possible with full details of the damage that
has occurred. Retain the equipment and packing materials for inspection. Check that all
parts have been received as ordered. Make sure that all packaging is removed from the
unit before use. This unit is guaranteed for 2 years from the date of manufacture. The UV
LED lamp is guaranteed for 3 years from the date of manufacture against manufacturer’s
defects. Lamps should be replaced every 3 years.

4. Installation Instructions:
DANGER: You must NOT connect the unit into a lighting circuit.
WARNING: You must connect the power cable to a standard power outlet.
Connecting the Power Source
DANGER: SERVICING OF DOUBLE-INSULATED APPLIANCES
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No
grounding means is provided on a double-insulated appliance, nor should a means for grounding
be added to the appliance. Servicing of a double-insulated appliance requires extreme care and
knowledge of the system and should be done only by a qualified service personnel. Replacement
parts for a double insulated appliance must be identical to those parts in the appliance.
A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE
INSULATED”. The symbol (square within a square) may also be marked on the appliance.
Once installed as above and mounted correctly, fit the mains plug into the power outlet.
Click
Click
1. Pull down the tab with an arrow to
insert or remove the correct pin
adaptor into the mains plug housing.
2. Plug the jack end of the power cable
into the socket at the back of the
Lumnia unit.

5. Positioning the Unit
Figure 1:
Position the unit on a suitable wall at a minimum
height of 6’1” (1.86 M) to the bottom of the unit.
Figure 1 illustrates the suggested mounting height.
A ladder should not be required for servicing at this
height.
Position the unit as far as possible from sources of
ambient light. Ambient light can cause inecient
capture of flying insects. Ideally position the unit
so the cable entry is within 4’9” (1.5M) of an electric
outlet. If this is not possible the unit must be
connected safely by a qualified electrician.
To ensure that the product minimises risk UV exposure especially to eyes, it is
recommended that the product is installed at a minimum height of 6’1” (1.86 M) from the
bottom of the unit and also at least 3’3” (1M) from any area that may have persons occupying
for more than 4 hours in a day (see Figure 2).
It is also recommended that the product is not installed higher than 6’1” (1.86 M) to ensure
that the product can be maintained by the majority of technicians without the use of a
ladder.
Figure 2:
6’1” (1.86 M)
3’3” (1M) 3’3” (1M)
6’1” (1.86 M)

Figure 3:
DO NOT position the unit directly over areas where food is prepared, or where
uncovered food is stored.
DO NOT position unit directly over sources of heat.
For safety reasons, the unit contains a micro switch that disables the UV lamp if the
front cover is removed.
Figure 3 indicates the size and space considerations for mounting the product above
furniture.
6. Positioning Guide
• Not facing entry/exit point or windows - to avoid attracting unwanted insects or
competing light sources.
• Avoid putting on same surface as competing light source.
• Mounting on clear surface preferable to maximise UV footprint.
• Maximise line of sight (i.e. Have clear line of sight from any point within coverage
area away from food source or high risk area).
• When positioning the unit, ensure the desired power socket is within 4’9” (1.5 M) of
the cable socket at the back of the unit.
• This unit is an indoor product and should not be used outdoors.
Operational Service Mode
When the product is operational, the front icon will illuminate blue.
When in Service Mode or the front cover is open the front icon will illuminate red.
2.8” (71.7mm)
7.4” (188mm)
1.2” (30 mm)
21.8” (553 mm)

Ø15/64” (6mm)
7. Installation Preparation
6”1’ (1.86 M)
8. Fit & Removal of the Front Cover
Remove: Lift the tab located on the left hinge plate and slide the cover to the right to
remove.
Fit: Line up the front cover so that both the left and right hinge plates sit to the right of
the clasps on the unit. Slide cover to the left to fit into place.
Click

9. Removing and Replacing the
UV - LED Lamp
For lamp identification refer to reference number on Lamp. Only Lamps specified
in Section 14 - Accessories and Spares to be used with this product.
Do not touch LED when
servicing, maintaining or
cleaning the lamps.
Removing UV - LED Lamp
1. Press lamp into the
right hand side fitting
2. Release left side of
lamp from fitting
3. Remove lamp from
right hand side fitting
NOTE: Ensure the lamp is pushed firmly back into the left hand fitting.
1. Insert & press lamp to
the right hand side fitting
2. Insert lamp into left
hand side fitting
Fitting UV - LED Lamp
LED

Fold Flex
Remove Liner
11. Preparing the Glue Board
10. Mounting Lumnia
SECURE WITH
ALL 4 X SCREWS
NOTE: Remove lamps before screwing
Tighten
Fold Flex
Remove Liner
Fold Flex
Remove Liner
Fold Flex
Remove Liner
Fold Flex
Remove Liner
Remove Liner
Fold Flex

12. Installing & Removing the Glue Board
Pull down bottom
cover
Installing glue board
Removing glue
board
Installed
13. Adjusting the Light Output
1 2
The front cover can be manually
rotated to allow adjustment of the
light output (Figure 4).
The panel at the top of the unit can
be removed to optimise light output
when required (Figure 5).
Figure 4
Figure 5
NOTE: Front cover can be either fitted or removed for servicing the glueboard. See Section 8
for details.

14. Accessories and Spares
For a list of the Lumnia accessories and spares see below:
15. Product Disposal
16. Specification
Spares:
• UV-LED Lamp: 304816
• Glue Board (Pack of 10 Black): 305057
• Glue Board (Pack of 10 White): 305056
Accessories:
• Mains Plug, Cable and Pin
Adaptors - 305067
We hereby declare that model Lumnia Slim conforms covering the appliance
provisions of applicable US Federal requirements, including 21 CFR Part 1040,
Chapter 1, Sub-chapter J, Radiological Health.
The Lumnia Slim is classified as electrical or electronic equipment, according to the
Waste of Electrical and Electronic Equipment (WEEE) directive. Do not dispose of
this product with other household or commercial waste. Contact the agent who sold
the product for recycling advice.
EPA Est. No. 92685-MYS-1
The product described in this manual is subject to continuous development and
improvement and Rentokil reserve the right to alter the specification or design without
prior notice. Rentokil cannot accept any liability for any loss or damage arising from
the use of any information contained within this manual, or from any incorrect use
of the product described herein. Rentokil can accept no liability whatsoever for any
loss or damage arising from the product being serviced maintained or repaired by
unauthorised personnel.
12. Installing & Removing the Glue Board
Parameter Value
Power Supply 26 - 30V
Servicing When servicing, use only
identical replacement parts.
Power Consumption 12W
Replacement Tubes Rentokil type SKU: 304816
Size W: 21.8” (553mm) H: 7.4“ (188mm) D: 2.9” (71.8mm)
Weight:
• Boxed Unit 4.7 lb (2.14 kg) (boxed)
• Unit including Lamps & Glueboard 2.5 lb (1.12 kg)
IP Rating IP24

Problem Solution
Icon is blue / lamp not illuminated.
Icon is blue / lamp not illuminated.
Icon is red.
Icon is not lit.
Icon is red but on closing the
covers is flashing or goes o and
lamps do not light.
Check Lamp is fully inserted into Lamp
connector on the left hand side.
Check for LED lamp faults or damaged LED.
Replace LED lamp.
Ensure that the Front Cover is fully inserted
and clipped into place. Also check the
Bottom Cover is fully rotated into the
uppermost position.
Ensure that DC Power Jack is fully inserted
into the socket.
Check the power supply to the unit.
17..Troubleshooting
See Section 5 for reference to illuminated icon.

NOTES

NOTES

© 2019 RENTOKIL INITIAL PLC ALL RIGHTS RESERVED
2019 Rentokil Initial plc. Registered in England 5393279.
Blackwater, Camberley, Surrey, GU17 9AB
The names Rentokil® and Initial® are registered trademarks
GSD-160087 - V3 USA
Why Choose Rentokil?
Rentokil is the global leader in pest control, bringing expert, reliable and
professional service to commericial and residential customers in over 60 countries
worldwide. As the experts in pest control, we work closely with you to:
Give you peace of mind.
With over 12,000 qualified technicians worldwide, we have extensive experience
across a wide range of industry sectors. Our experts work proactively in
partnership with you to minimise the threat of pest infestations in your business.
Safeguard your reputation
We take a dual approach, incorporating both preventative and responsive
strategies to enhance protection for your business through a consistent,
continuous pest control programme.
Neither the whole nor any part of the information described in this manual, nor the
product therein described, may be adapted or reproduced in any form without prior
written approval of Rentokil.
The product described in this manual is subject to continuous development and
improvement and Rentokil reserve the right to alter the specification or design
without prior notice. Rentokil cannot accept any liability for any loss or damage arising
from the use of any information contained within this manual, or from any incorrect
use of the product described herein. Rentokil can accept no liability whatsoever for
any loss or damage arising from the product being serviced maintained or repaired
by unauthorised personnel.
For more information about Rentokil visit www.rentokil.com
Registered Design - refer to www.rentokil-initial.com/ip
Refer to Lumnia Slim Manual
for full installation instructions,
scan the QR code or visit:
www.rentokil.com/manuals