Phaesun 360123 User manual

Phaesun GmbH · Brühlweg 9 · 87700 Memmingen · Germany · Telefon [phone] - 0 · Telefax [phone] · [e-mail] · www.phaesun.com
360123 •08/2016
INSTRUCTION MANUAL:
Table Fan Fast Breeze
Remarks:
Electrical connections shall be in accordance with national or local codes.
READ AND SAVE THIS
INSTRUCTION MANUAL!

Phaesun GmbH · Brühlweg 9 · 87700 Memmingen · Germany · Telefon [phone] - 0 · Telefax [phone] · [e-mail] · www.phaesun.com
.INSTALLATION
1. connect the DC+ wire (brown) to the load(+)
terminal and the DC- wire (blue) to the load(–)
terminal of a charge controller with low
voltage disconnection
2. An integrated polarity protection prevents
damages. If the cables are connected in the
wrong polarity, the DC fan is not serviceable.
Please check installation and connect with
correct polarity.
3. insert the DC-plug into the socket at backside
of fan base
Instruction for installing DC-TABLE FAN
DC+
(brown) DC–
(blue)
ASSEMBLY
1. Loosen Guard Mounting Nut from the Motor
Housing.
2. Position rear guard firmly to motor housing
and then fasten by turning guard’s mounting
nut clockwise tightly.
3. Push the blade along motor shaft. Fasten
it firmly with Blade Locking Nut by turning
counter clockwise.
4. Hang the Front Guard to Rear Guard with the
position fixer provided at the rim of Guard, and
then fix together with clips and screw provided.
.SPEED CONTROL
Select the desired speed with the speed switch
on the base on the fan: 0 for OFF, 1 for low
speed, 2 for medium speed and 3 for high
speed.
.OSCILLATION CONTROL
1. Push the oscillation knob to oscillate.
2. Pull the oscillation knob to stop.

Phaesun GmbH · Brühlweg 9 · 87700 Memmingen · Germany · Telefon [phone] - 0 · Telefax [phone] · [e-mail] · www.phaesun.com
Warning:
If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent
or similar qualified person in order to avoid a
hazard. Be sure to shut off electric supply at
main switch or circuit breaker before installation.
The important safeguards and instruction
appearing in this manual are not meant to cover
all possible conditions and situation that may
occur. It must be understood that common
sense, caution and care are factors which cannot
be built into any product. These factors must be
supplied by the personcaring for and operating
the until.
No responsibility will be accepted for any
damage which may occur during transport or by
improper installation or voltage fluctuation or if
any portion of the product has been altered or
modified.
Instruction for installing DC-TABLE FAN
CAUTION
1. Improper installation may result in the risk of
fire, electric shock, or injury to persons.
2. To prevent risk of fire and electric shock, do
not use the unit near windows.
3. plug must be removed from sock before clea-
ning, servicing, maintenance and move from
one location to another.
4. The fan should be placed on a flat and stable
surface when operating to avoid overturning.
5. The fan should not be placed in a damp
place or where humidity is high (such as in a
bathroom).
6. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
7. Children should be supervised to ensure that
they do not play with the appliance.
8. If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order to
avoid a hazard.

Phaesun GmbH · Brühlweg 9 · 87700 Memmingen · Germany · Telefon [phone] - 0 · Telefax [phone] · [e-mail] · www.phaesun.com
Parts description
1. Front Guard
2. Blade Locking nut
3. Blade
4. Guard mounting nut
5. Rear guard
6. Motor
7. Oscillation knob
8. Stand
9. Speed switch
10. Base
11. DC cable
Technical Data
Speed level switch 1 2 3
Power 3,8 W 7,0 W 12,4 W
Moter speed 800 rpm 1050 rpm 1280 rpm
Air-flow 370 m³/h 580 m³/h 720 m³/h
System voltage 12 VDC
Oscillation degree 70°
Dimension H x L x W 500 x 345 x 270 mm
Weight 2,1 kg
Material 3 blades, white/grey plastic (PP), metal guard
Motor brushless DC-motor