Philips AZ1123W/05 User manual

AZ1123WCD Soundmachine
User Manual

1
6
7
8
!
@
1
2
9
0
4
3
5
AC MAINS~
PHONES
6 x R14 • UM-2 • C-CELLS

X
PRO
REP ALL
SHUF
2
3
4
5
6
7

English Controls/Power Supply
Supplied Accessories
– AC power cord
Top/front panels (See 1)
1 Source selector:CD , FM , MW or OFF
– selects CD or radio (FM/MW) source of
sound
– power off switch
2 2; – starts or pauses CD playback
§ ∞
– selects the next/previous track
– fast searches forwards/backwards
(press and hold the button)
PROG – programs tracks and reviews the
program
9 – stops CD playback;
– erases a CD program
3 Display – shows the CD functions
4 REPEAT – repeats a track/
CD program/entire CD.
5
SHUFFLE –plays all tracks in random order
6OPEN•CLOSE – opens/ closes the CD
door
7TUNING – tunes to radio stations
8
VOLUME – adjusts volume level
Back/bottom panels (See 1)
9Telescopic antenna – improves FM
reception
0Battery door – open to insert 6 x 1.5V
R-14/UM-2/C-cells
!p–3.5 mm stereo headphone socket
Helpful hints: The speakers will be muted
when headphones are connected to the set.
@AC MAINS~ – inlet for power cord
CAUTION
- Visible and invisible laser radiation.
If the cover is open, do not look at
the beam.
- High voltage! Do not open.You run
the risk of getting an electric shock.
The machine does not contain any
user-serviceable parts.
- Modification of the product could
result in hazardous radiation of EMC
or other unsafe operation.
This set complies with the radio
interference requirements of the
European Community.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1Open the battery door and insert 6 batteries,
type R-14,UM-2 or C-cells, (preferably alka-
line) with the correct polarity as indicated by
the "+" and "–" symbols inside the compart-
ment (See 1).
2Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set is
now ready to operate.
• Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
• Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type for
the set.
• When inserting new batteries, do not try to mix
old batteries with the new ones.
• Remove the batteries if the set is not to be used
for a long time.
Batteries contain chemical substances, so
they should be disposed of properly.

--
Power Supply General Operation/Tuner
Using AC power
WARNING: Always check you have
completely switched off the set, before
you change or disconnect power supply.
1Check if the power voltage, as shown on
the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2Connect the power cord to the
AC MAINS~ inlet and the wall socket.The
set is now connected and ready for use.
3To switch the set off completely, withdraw the
power cord from the wall socket.
4Install the unit near the AC outlet and where
the AC power plug can be easily reached.
• Disconnect the power cord from the wall
socket to protect your set during heavy thun-
derstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.
The type plate is located on the
bottom of the set.
Helpful hints:
–To avoid unnecessary energy consumption, always
adjust the
Source selector to OFF after
using the set.
General operation
Switching on and off and selecting the
function
1To select your sound source, adjust the
Source selector to: CD, FM or MW.
2To switch off the set, adjust the
Source selector to OFF position.
Adjusting volume
Adjust the sound with the VOLUME control.
Radio reception
1Adjust the Source selector to FM or MW
to select your desiredwaveband.
2Tu r n TUNING to tune to a station.
Helpful hints:
To improve radio reception
• For FM, extend, incline and turn the
telescopic antenna for best reception. Reduce
its length if the signal is too strong.
• For MW, the set uses a built-in antenna.
Direct this antenna for best reception by turn-
ing the whole set.

Playing a CD
• This CD player plays Audio Discs including
CD-Recordables (CD-R) and CD-Rewritables
(CD-RW).
• MP3, CD-ROM, CD-I, CDV,VCD, DVD or
computer CDs are not possible for playback.
IMPORTANT!
CDs encoded with copyright protection
technologies by some record companies may
be unplayable by this product.
1Adjust the Source selector to CD.
2Open the CD door.
3Insert a CD with the printed side facing up,
then press the CD door gently to close.
➜Display shows --, and later the total
number of tracks. (See 2)
4Press
2; to start playback.
5To pause playback, press
2; .
➜
Display: 2flashes. (See 3)
6To resume, press
2; again.
7To stop CD playback, press
9 .
Helpful hints:
CD play will also stop when:
–you open the CD door;
–you select FM , MW or OFF ;
–the CD has reached the end.
Selecting a different track
•Press ∞/§ once or repeatedly until the
desired track number appears in the display.
•In the pause/stop position, press 2; to start
playback.
Finding a passage within a
track
1During playback, press and hold ∞or § .
➜ The CD is played at high speed and with
reduced volume.
2When you recognize the passage you want,
release ∞or §to resume normal playback.
Helpful hints:
–When your searching reaches the end of the
last track, the CD goes to stop mode.
Programming track num-
bers
You may store up to 20 tracks in the desired
sequence. If you like, store any track more
than once.
1In the stop position, press PROG to
activate programming.
➜Display: PROG and 00 flash. (See 4)
2Press
∞ or § to select your desired track
number.
3Press PROG to store the desired track
number.
➜Display: PROG and 00 flash for you to
program the next track.
4Repeat steps 2to 3to select and store all
desired tracks in this way.
➜If you attempt to store more than 20
tracks, no track can be selected and the
display shows flashing --.
5To play your program, press 2; .
Helpful hints :
–When playback of your program comes to
the stop position, your set will return to nor-
mal playback.To re-enter program mode,
press PROG in the stop position.
CD Player

--
Reviewing the program
In the stop position, press PROG repeatedly
to see your stored tracks.
Erasing a program
You can erase the contents of the memory
by:
– in the stop position, press PROG to enter
program mode, and then press
9 ;
– selecting
FM , MW or OFF ;
– opening the CD door.
Different play modes:
REPEAT and SHUFFLE
(See 5,6)
REPEAT
You can play the current track or the whole
disc repeatedly, and combine REPEAT modes
with PROGRAM.
REP –plays the current track continuously.
REP ALL –repeats the entire CD/program.
1To select play mode, press REPEAT once or
more.
➜ The display shows REP or REP ALL.
2Press 2; to start playback if in the stop/pause
position.
3To return to normal playback, press REPEAT
repeatedly until the modes are no longer dis-
played.
–You can also press 9to cancel your play
mode.
SHUFFLE
You can play all the tracks in random order.
1In the stop position, press SHUFFLE to
switch on shuffle play.
➜ Display shows SHUF.
2To switch off shuffle play, press 9.
Helpful hints:
–During the shuffle play, when REP function is
selected, it will play the current shuffled track
repeatedly, or when the REP ALL function is
selected, it will repeat the shuffle play of the
entire CD.
–Shuffle play is not available in the program
mode.
CD Player

--
CD player and CD handling
• If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.
• The lens of the CD player should never be
touched!
• Sudden changes in the surrounding
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the lens
but leave the set in a warm environment until
the moisture evaporates.
• Always close the CD-tape door to avoid dust
on the lens.
• To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
• Never write on a CD or attach any stickers to
it.
Safety information
• Place the set on a flat, hard and stable surface
so that the system does not tilt.
• Where the MAINS plug or an appliance cou-
pler is used as the disconnect device, the dis-
connet device shall remain readily operable.
• Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
• The apparatus shall not be exposed to drip-
ping or splashing.
• Adequate ventilation with a minimum gap of
15cm (6 inches) between the ventilation holes
and surrounding surfaces is necessary to pre-
vent heat build-up.
• Do not cover the ventilation openings with
items such as newspapers, table-cloths, cur-
tains, etc.
• No objects filled with liquids, such as vases,
shall be placed on the apparatus.
• No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.
• The mechanical parts of the set contain
self-lubricating bearings and must not be oiled
or lubricated.
• To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Maintenance & Safety (See 7)
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.

--
Problem
–Possible cause
• Remedy
No Sound/Power
–Volume not adjusted
• Adjust the VOLUME
–Power cord not securely connected
• Connect the AC power cord properly
–Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
–Headphones connected to the set
• Disconnect headphones.
–CD contains non-audio files
• Press ∞,§ once or more to skip to a CD audio
track, instead of the data file.
Display does not function properly / No
reaction to operation of any of the
controls
–Electrostatic discharge
• Switch off and unplug the set. Reconnect after a
few seconds
Severe radio hum or noise
–Electrical interference: set too close to TV, VCR or
computer
•Increase the distance
Poor radio reception
–Weak radio signal
•FM: Adjust the FM telescopic aerial
-- indication
–No CD inserted
• Insert a CD
–CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
–Laser lens steamed up
• Wait until lens has cleared
–CD-R/CD-RW is blank or not finalized
• Use a finalized CD-R/CD-RW or suitable CD
Audio disc only
Note:
Make sure the CD is not encoded with
Copyright protection technologies, as some
do not conform to the Compact Disc stan-
dard.
The CD skips tracks
–CD damaged or dirty
• Replace or clean CD
–Program/Shuffle is active
• Quit program/shuffle mode
Note: A CD badly scratch or dirty may result in
improper operation.
Troubleshooting
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING: Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this will
invalidate the guarantee.

--
Disposal of your old product
Your product is designed and manufactured with high quality materials and com-
ponents, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to
a product it means the product is covered by the
European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical
and electronic products.
Please act according to your local rules and do not dispose of your old products
with your normal household waste.The correct disposal of your old product will
help prevent potential negative consequences for the environment and human
health.
Hearing Safety
Listen at a moderate volume.
• Using headphones at a high volume can impair your hearing. This product can produce sounds in
decibel ranges that may cause hearing loss for a normal person, even for exposure less than a
minute. The higher decibel ranges are offered for those that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of
sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to your
hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave
it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
Listen for reasonable periods of time:
• Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss.
• Be sure to use your equipment reasonably and take appropriate breaks.
Be sure to observe the following guidelines when using your headphones.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume as your hearing adapts.
• Do not turn up the volume so high that you can't hear what's around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may cre-
ate a traffic hazard and is illegal in many areas.

Printed in China PDCC_ZC/JH-0727
W
CLASS 1
LASER PRODUCT
AZ 1123W
English
Meet Philips at the Internet
http://www.philips.com