Philips HD6592 User manual

HD6596, HD6592
11600.pdf 1 01/11/17 14:09

1 2
3
4
5
16
6
7
8
9
10
11
12
13
14
15
1

English 6
Deutsch 18
Français 31
Nederlands 44

English
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that
Philips offers, register your product at www.philips.com/welcome.
Clean cold water
Use clean cold water every day. If you have not used the coffee machine for one day, you have to
flush it with clean cold water before you use it again. To flush the machine, fill the water reservoir with
clean cold water, place a bowl (with a capacity of at least 1500 ml) or 2 cups under the coffee spout
and press the 2-cup button a few times to brew hot water until the water reservoir is empty.
Fresh filter coffee
To brew a jug of delicious coffee use good-quality pre-ground coffee . Always use a paper filter size
102.
You can brew up to 7 cups of coffee in the jug.
Fresh coffee pods
Use good-quality fresh coffee pods in this machine for a full, round taste. To keep the pods fresh
longer, store them in a storage container.
Intensity select
-For one small cup of strong short coffee, double press the 1-cup button (Fig. 2).
-For two cups of strong short coffee, double press the 2-cup button (Fig. 3).
Important
Read this user manual carefully before you use the machine and save it for future reference.
Danger
-Never immerse the machine in water or any other liquid.
Warning
-Check if the voltage indicated on the bottom of the machine
corresponds to the local mains voltage before you connect the
machine.
-Connect the machine to an earthed wall socket.
-If the mains cord is damaged, you must have it replaced by
Philips, a service center authorized by Philips or similarly qualified
persons in order to avoid a hazard.
-Do not use the machine if the plug, the mains cord or the machine
itself is damaged.
6English

-This machine can be used by children aged from 8 years and
above and by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
machine in a safe way and if they understand the hazards
involved.
-Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised.
-Keep the machine, its accessories and its cord out of the reach of
children aged less than 8 years.
-Children shall not play with the machine.
Caution
-Always return the machine to a service center authorized by
Philips for examination or repair. Do not attempt to repair the
machine yourself, otherwise your warranty becomes invalid.
-After unpacking the machine, never put your SENSEO® machine
on its side. Always keep it in upright position, also during
transport.
-Never put normal ground coffee or use torn pods in the machine,
as this causes it to become blocked.
-Do not use the machine in combination with a transformer, as this
could cause hazardous situations.
-Do not use the machine in combination with a transformer, as this
could cause hazardous situations.
-Always put the machine on a flat and stable surface.
-Do not place the machine on a hotplate or directly next to a hot
oven, heater or similar source of heat.
-Never let the machine operate unattended.
-Do not use the machine at altitudes higher than 2200 meters
above sea level.
-Never pour any other liquid than clean cold water into the water
reservoir.
7
English

-Never flush the machine or let it brew coffee when the spout is
not in place.
-Flush the coffee machine with fresh water before you use it for
the first time. This causes the system to fill with water, which is
essential for the machine to work properly.
-Do not use the machine in combination with water softeners
based on sodium exchange.
-Descale your machine regularly. The machine indicates when
descaling is needed. Not doing this will make your machine stop
working properly. In this case, repair is not covered by your
warranty.
-Never use a descaling agent based on mineral acids such as
sulphuric acid, hydrochloric acid, sulphamic acid and acetic acid
(e.g. vinegar). These descaling agents may damage your coffee
machine.
-The machine is intended for normal household use only. It is not
intended for use in environments such as staff kitchens of shops,
offices, farms or other work environments, nor is it intended to be
used by clients in hotels, motels, bed and breakfast and other
residential environments.
-Do not disassemble the insulated jug.
-Never immerse the insulated jug in water or any other liquid, as
this could cause water to enter between the walls of the jug.
-When the insulated jug is filled with coffee, keep it in upright
position to prevent leakage.
-The insulated jug is not dishwasher-proof.
-During brewing and until the light stops blinking, the filter holder
is filled with hot coffee.
Electromagnetic fields
This Philips machine complies with all applicable standards and regulations regarding exposure to
electromagnetic fields.
8English

General description
1 1-cup pod holder
2 2-cup pod holder
3 Distribution disk
4 Collector ring
5 Drip tray
6 CALC light
7 Jug button
8 2-cup button
9 1-cup button
10 Water reservoir lid
11 Water reservoir
12 Filter holder lid
13 Filter holder
14 Insulated jug lid
15 Insulated jug
16 Measuring spoon
First use
The machine starts an automatic flushing cycle when you switch it on for the first time, no matter
which button you press.
1Put the plug in an earthed wall socket.
2Remove the water reservoir from the machine and remove the lid from the water reservoir (Fig. 4).
3Clean the water reservoir thoroughly in hot water, if necessary with some washing-up liquid.
4Fill the water reservoir with clean cold water up to the MAX indication (Fig. 5).
5Put the lid back onto the water reservoir and put the water reservoir back onto the machine (Fig. 6).
6Place the 1-cup pod holder in the coffee machine. Close the lid and make sure it is properly locked
(Fig. 7).
7Remove the drip tray from the platform and put a bowl (with a capacity of at least 1.5 liters) or the
jug under the coffee outflow (Fig. 8).
8Press one of the buttons on the control panel. The jug button, 2-cup button and 1-cup button flash
in sequence (Fig. 9).
9The flushing cycle starts. During the flushing cycle the system fills itself with water from the water
reservoir. The machine produces more noise than during a regular brewing cycle.
10 The machine switches off when the water tank is empty (Fig. 10).
11 After the first flushing cycle, clean the collector ring and the pod holders with hot water and some
washing-up liquid or in the dishwasher.
Brewing a jug of drip-filter coffee
1Open the lid of the machine (Fig. 11).
2Remove the pod holder, if present (Fig. 12).
3Remove the drip tray, if present.
4Fill the water reservoir with clean cold water up to the level required for the number of cups of
coffee you wish to brew and put the water reservoir back onto the machine (Fig. 13).
5Rinse the insulated jug with hot tap water to preheat it .
Tip: To obtain the tastiest and hottest coffee, brew at least half a jug of coffee.
6Place the filter holder on top of the insulated jug (Fig. 14).
9
English

7Open the lid of the filter holder.
8Put a paper filter size 102 in the filter holder. Make sure that you fold the sealed edges to ensure
that the paper filter stays upright during brewing (Fig. 15).
9Use the measuring spoon to put the required amount of pre-ground coffee in the filter (Fig. 16).
Tip: Use one measuring spoon of pre-ground coffee for each cup. Use a heaped measuring spoon
for strong coffee and a level measuring spoon for mild coffee.
10 Close the lid of the filter holder.
11 Slide the insulated jug on the platform of the machine (Fig. 17).
12 Press the jug button to start the brewing process (Fig. 18).
-The light in the jug button starts flashing and the brewing process starts. (Fig. 19)
Note: If the jug button and the CALC light start flashing alternately during heating up and brewing
(Fig. 20), you need to descale the machine (see 'Descaling the machine').
-When all the water from the water reservoir has passed through the filter, the light in the jug
button goes out and the machine switches off automatically.
13 You can now remove the insulated jug from the machine (Fig. 21).
14 Remove the filter holder from the insulated jug (Fig. 22).
Tip: You can place the filter holder on the drip tray to prevent coffee from leaking onto your
worktop while you pour out coffee from the jug (Fig. 23).
15 Place the jug lid on the insulated jug and turn it to the keep-warm position (closed lock symbol)
(Fig. 24).
16 Push the lever of the jug lid to pour coffee into one or more cups (Fig. 25).
Brewing pod coffee
Brewing one cup of pod coffee
1Fill the water reservoir with clean cold water up to the MAX indication and put it back onto the
machine (Fig. 5).
Note: The MIN indication on the water reservoir indicates the minimum amount of water required
for brewing pod coffee. Always fill the water reservoir beyond the MIN level.
2Put the plug in an earthed wall socket.
3Open the lid of the machine by moving the lever upwards (Fig. 11).
4Place the drip tray on the platform of the machine (Fig. 26).
5Place one pod in the 1-cup pod holder with the convex side pointing downwards (Fig. 27).
Note: Make sure that the pod holder is clean and the sieve in the center is not clogged, e.g. with
loose coffee grounds.
Note: Make sure that the coffee in the pod is distributed evenly and press the pod lightly into the
pod holder.
6Place the 1-cup pod holder in the machine and close the lid (Fig. 7).
7Place a cup on the drip tray (Fig. 28).
8Press the 1-cup button to brew coffee. (Fig. 29)
-The button starts flashing and the machine starts heating up (Fig. 30).
Note: If the 1-cup button and CALC light start flashing alternately during heating up and brewing
(Fig. 31), you need to descale the machine (see 'Descaling procedure ').
10 English

-When the heating-up process is finished, the machine starts brewing coffee (Fig. 32). After
brewing, the machine switches off automatically.
Tip: Double press the 1-cup button (Fig. 2) to brew a strong short cup of coffee.
9Remove the coffee pod after use by lifting the pod holder out of the machine and emptying it (Fig.
33).
Caution: Be careful when you do this, for there may still be some hot water/coffee on the coffee
pod(s).
Caution: Never put normal ground coffee or use torn pods in the machine, as this causes it to
become blocked.
Brewing two cups of pod coffee
1To brew two cups of pod coffee, place the deeper 2-cup pod holder in the machine. Place two
pods in the 2-cup pod holder (Fig. 34).
2Press the 2-cup button to brew coffee (Fig. 35).
-The button starts flashing and the machine starts heating up (Fig. 36).
Note: If the 2-cup button and the CALC light start flashing alternately during heating up and
brewing (Fig. 37), you need to descale the machine (see 'Descaling the machine').
-When the heating-up process is finished, the machine starts brewing coffee (Fig. 38). After
brewing, the machine switches off automatically.
Tip: Double press the 2-cup button (Fig. 3) for two cups of strong short coffee.
3Remove the coffee pods after use by lifting the pod holder out of the machine and emptying it (Fig.
33).
Brewing special coffees
1To brew a special coffee, place a cappuccino pod, a hot chocolate pod or another special coffee
pod in the 2-cup pod holder.
2Place a cup under the coffee spout.
3Press the 1-cup button to brew your special coffee.
Cleaning the machine
Never immerse the machine in water or any other liquid.
Never clean the machine by flushing it with the lid open.
Cleaning the coffee machine
Warning: Always unplug the machine before you clean it.
1Clean the outside of the machine with a moist cloth.
2To prevent clogging, clean the pod holders regularly with hot water, some washing-up liquid and a
washing-up brush. If you have used the 2-cup pod holder to brew cappuccino or hot chocolate,
make sure to clean it thoroughly immediately after use to remove any milk residues.
Note: You can disassemble the pod holders for more thorough cleaning (Fig. 39).
11
English

3Clean the collector ring, the pod holders, the drip tray, the water reservoir and the water reservoir
lid in hot water, if necessary with some washing-up liquid. All detachable parts except for the water
reservoir and the insulated jug can also be cleaned in the dishwasher (Fig. 40).
4Clean the water distribution disk with a moist cloth. Be careful when you do this. Make sure that the
rubber sealing ring does not get stuck under the edge of the water distribution disk. If it does, the
coffee machine starts to leak.
Cleaning the insulated jug
Warning: Do not immerse the insulated jug in water or any other liquid and do not clean
it in the dishwasher as this will damage the jug.
1To remove the jug lid, turn the lid anticlockwise to 'open' position and remove it (Fig. 41).
2Clean the inside of the insulated jug with a soft brush, hot water and some washing-up liquid (Fig.
42).
Tip: To remove stubborn brown deposits, fill the jug with hot water and add a spoonful of baking
soda. Let the baking soda do its work for some time.
3After cleaning, rinse the insulated jug with fresh, hot water (Fig. 43).
Note: You can clean the jug lid in the dishwasher.
Flushing the coffee machine
If you have not used the coffee machine for one day, flush it with clean cold water before you use it
again. Flush the machine in the following way:
1Fill the water reservoir with clean cold water up to the MAX indication and put it back onto the
machine.
2Put the 1-cup pod holder or the 2-cup pod holder in the machine without pod(s).
3Put a bowl (with a capacity of at least 1.5 liters) or the jug under the coffee spout to collect the
water.
4Press the 2-cup button, wait until the machine has heated up and brewed an amount of hot water.
Then press the 2-cup button several times until the water reservoir is empty.
Descaling the machine
When to descale
Scale builds up inside the machine during use. It is essential to descale the machine when the CALC
light starts flashing during heating up or brewing (Fig. 31).
Why to descale
Your reasons to descale:
-It prolongs the life of your coffee machine
-It ensures maximum cup volume
-It ensures maximum coffee temperature
-The machine produces less sound during brewing
-It prevents malfunctioning
12 English

If the descaling procedure is not performed correctly, scale residue remains behind in the machine.
This causes scale to build up more quickly and may cause permanent and irreparable damage to the
machine.
Use the correct descaler
Only citric acid-based descalers are suitable for descaling the machine. This type of descaler descales
the machine without damaging it. For the correct amount, see under ‘Descaling procedure’ below.
Each descaling mixture can be used only once. Use a new descaling mixture each time. We advise you
to use the special SENSEO® Descaler (HD7012/HD7011). Read the instruction leaflet in the package.
For more information on why it is important to descale, how to descale or which descaler to use, visit
our website at www.philips.com/descale-senseo.
Warning: Never use a descaler based on mineral acids such as sulphuric acid,
hydrochloric acid, sulphamic acid and acetic acid (e.g. vinegar). These descalers may
damage your coffee machine.
Descaling procedure
The descaling procedure consists of two descaling cycles and two flushing cycles. Do not interrupt the
descaling cycles and do not switch off the machine before you have performed the two flushing
cycles.
1Fill the water reservoir with clean cold water up to the MAX indication and pour the water into a
bowl (Fig. 44).
2Mix 50 grams of citric acid with the water in the bowl. Stir until the powder has dissolved (Fig. 45).
3Fill the water reservoir with the descaling mixture and place it back on the machine (Fig. 47).
4Remove the drip tray. Put a bowl with a capacity of at least 1.5 liters under the spout to collect the
descaling mixture (Fig. 8).
5Place the 1-cup pod holder with a used coffee pod in it in the coffee machine. Close the lid and
make sure it is properly locked.
Note: Always put a used coffee pod in the pod holder when you descale the machine. This pod
serves as a ‘filter’ to prevent the sieve or hole in the pod holder from getting clogged with scale
residue.
Warning: Make sure that the lid is closed properly and the lid lever is locked before
you start descaling the machine.
6Press the 1-cup button and the 2-cup button simultaneously.
7During the descaling cycle, the water comes out of the machine at intervals. The CALC light, jug
button, 2-cup button and 1-cup button flash slowly in sequence (Fig. 46).
8When the water reservoir is empty, the 1-cup button and CALC light start to flash quickly alternately
(Fig. 31).
9Empty the bowl and place it back. Remove the used pod and the 1-cup pod holder. Place the
2-cup pod holder with one used pod in the machine. Close the lid.
10 Fill the water reservoir with clean cold water up to the MAX indication and pour the water into a
bowl (Fig. 44).
11 Mix 50 grams of citric acid with the water in the bowl. Stir until the powder has dissolved (Fig. 45).
12 Fill the water reservoir with the descaling mixture and place it back on the machine (Fig. 47). Then
press the 1-cup button to start the second descaling cycle.
13
English

13 When the 1-cup button and the CALC light start to flash quickly alternately (Fig. 31), remove the
used pod from the 2-cup pod holder. Clean the water reservoir by rinsing it thoroughly with cold
clean tap water a few times (Fig. 48).
14 Fill the water reservoir with clean cold water up to the MAX indication and put it back onto the
machine.
15 Press the 1-cup button. The CALC light, jug button, 2-cup button and 1-cup button flash slowly in
sequence (Fig. 46). During the flushing cycle, the water comes out of the machine at intervals.
16 When all the water in the water reservoir has been used up, the 1-cup button and CALC light start
to flash quickly alternately (Fig. 31).
17 Repeat steps 13 and 14.
-When all the water in the water reservoir has been used up, the machine switches off and all the
lights go out to indicate that the descaling procedure has ended.
Ordering accessories
To buy accessories or spare parts, visit www.shop.philips.com/service or go to your Philips dealer.
You can also contact the Philips Consumer Care Center in your country (see the international warranty
leaflet for contact details).
Warranty and support
If you need information or support, please visit www.philips.com/support or read the international
warranty leaflet.
Recycling
-This symbol means that this product shall not be disposed of with normal household waste
(2012/19/EU) (Fig. 49).
-Follow your country's rules for the separate collection of electrical and electronic products. Correct
disposal helps prevent negative consequences for the environment and human health.
Troubleshooting
This chapter summarizes the most common problems you could encounter with the appliance. If you
are unable to solve the problem with the information below, visit www.philips.com/support for a list
of frequently asked questions or contact the Consumer Care Center in your country.
Problem Possible cause Solution
My coffee cup overflows
with cold coffee
You did not flush the machine
before first use.
Flush the machine before first
use.When the machine has emptied a
complete water reservoir, you can start
to make a new coffee.
The light in the button you
pressed flashes slowly.
The machine is heating up. If heating up takes longer than two
minutes, contact the Philips Consumer
Care Center in your country.
When you are brewing drip
filter coffee, the light flashes
slowly during brewing.
The brewing cycle last approximately
90 seconds, wait until the brewing
cycle has finished.
14 English

Problem Possible cause Solution
The light in the button you
pressed flashes quickly.
There is not enough water in
the water reservoir.
Fill the water reservoir.
The float in the water reservoir
is stuck.
Empty the water reservoir and shake it
a few times to release the float. Clean
the water reservoir with hot water and
some washing-up liquid or in the
dishwasher. If this does not help,
descale the machine (see chapter
‘Descaling’).
The CALC light flashes
when the machine is
heating up or brewing
coffee.
You need to descale the
machine.
Perform the descaling procedure as
described in chapter ‘Descaling’.
I cannot close the lid
properly.
Perhaps a used coffee pod is
sticking to the water
distribution disk.
If this is the case, remove the used pod.
The coffee machine
produces less pod coffee
than before.
Perhaps the sieve in the
center of the pod holder is
clogged.
If the sieve is clogged, use a washing-
brush to unclog the sieve. If you cannot
unclog it properly with the washing-up
brush, put the pod holder in the
machine and descale the machine.
Descale the machine (see chapter
‘Descaling’).
You may have double pressed
the 1-cup or 2-cup button.
If you double press the 1-cup or 2-cup
button within 3 seconds, the machine
brews one or two cups of short strong
coffee.
The temperature of the
coffee decreases quickly.
You use the wrong type of
cups.
Use thin-walled cups. Thin-walled cups
absorb less heat from the coffee than
thick-walled cups.
The cups are cold. Rinse the cups with hot water. You can
preheat the coffee machine and cup by
brewing a cup of hot water first without
placing a coffee pod in the pod holder.
You have added cold milk to
the coffee.
Do not use cold milk straight from the
refrigerator.
The filter coffee is not hot
enough.
You have not brewed a full jug. Coffee stays hot longer if you brew a
full jug of coffee to ensure that that the
coffee has the right temperature.
You have not removed the
pod holder.
If you do not remove te pod holder, this
can lead to a longer brewing time.
You have not preheated the
insulated jug.
Rinse the insulated jug with hot tap
water to preheat it .
15
English

Problem Possible cause Solution
You have added cold milk to
the coffee.
Do not use cold milk straight from the
refrigerator.
Coffee grounds end up in
the insulated jug.
Your paper filter may have
collapsed during brewing.
To prevent the paper filter from
collapsing, fold the sealed edges.
The coffee is weaker than
expected.
There may have been some
water in the insulated jug
when you started brewing
filter coffee.
Always make sure that there is no
water in the jug before you start
brewing coffee.
You have not used enough
pre-ground coffee.
Use one heaped measuring spoon of
pre-ground coffee per cup for stronger
coffee.
Water leaks from the
coffee machine.
You overfilled the water
reservoir.
Do not fill the water reservoir beyond
MAX level.
The sieve in the center of the
pod holder may be clogged.
Check the pod holder. If the sieve is
clogged, use a washing-up brush to
unclog the sieve. If you cannot clean it
properly with the washing-up brush,
put the pod holder in the machine and
descale the machine (see chapter
'Descaling').
The sealing ring may be stuck
under the edge of the
distribution disk.
Check if the sealing ring is stuck under
the edge of the distribution disk. If it is,
pull it out from under the distribution
disk carefully.
You forgot to place the
collector ring.
If you forget to place the collector ring,
water comes out of the lid of the
machine instead of passing through the
pod.
I cannot open the lid. A vacuum has formed under
the lid.
Switch of the coffee machine. Pull up
the lever and wait 24 hours before you
open the lid. You may need to use
some force.
Always make sure the pod holders are
clean and the center of the sieve is not
clogged to prevent a vacuum.
It takes longer than before
to brew filter coffee.
You have to descale the
machine.
To descale the machine, follow the
instructions in chapter 'Descaling'.
You left a pod holder in the
machine.
Remove the pod holder.
There is still water left in
the water tank after
brewing filter coffee.
This is normal. The filter coffee brewing process does
not use up all the water in the water
tank.This is normal.
16 English

Problem Possible cause Solution
I do not get a small cup of
stronger coffee after
double pressing the 1-cup
or 2-cup button.
You have double pressed the
button too fast or you have
waited longer than 3 seconds
after pressing the button for
the first time.
You can get a stronger coffee if you
double press the 1-cup or 2-cup button
within 3 seconds. The light in the
button shines less bright when the
selection of stronger coffee is
successful.
17
English

Deutsch
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf und willkommen bei Philips! Um die Unterstützung von Philips
optimal nutzen zu können, sollten Sie Ihr Produkt unter www.philips.com/welcome registrieren.
Sauberes kaltes Wasser
Verwenden Sie täglich sauberes kaltes Wasser. War die Kaffeemaschine einen Tag lang nicht in
Gebrauch, lassen Sie vor dem nächsten Aufbrühen sauberes kaltes Wasser durchlaufen. Um die
Maschine durchzuspülen, füllen Sie den Wassertank mit sauberem kaltem Wasser, stellen Sie eine
Schüssel (mit einem Volumen von mindestens 1500ml) oder zwei Tassen unter den Kaffeeauslauf,
und drücken Sie mehrmals die 2-Tassen-Taste, damit heißes Wasser durchläuft, bis der Wassertank
leer ist.
Frischer Filterkaffee
Um eine Tasse bekömmlichen Kaffee zu brühen, verwenden Sie gemahlenen Kaffee in guter Qualität.
Verwenden Sie immer Papierfiltertüten der Größe 102.
Sie können in der Kanne bis zu 7Tassen Kaffee brühen.
Frische Kaffeepads
Verwenden Sie frische, hochwertige Kaffeepads in dieser Maschine, um einen vollen, abgerundeten
Geschmack zu erhalten. Damit die Pads länger frisch bleiben, sollten Sie sie in einem entsprechenden
Behälter aufbewahren.
Intensitätsauswahl
-Für eine kleine Tasse starken Kaffee drücken Sie zweimal auf die 1-Tasse-Taste (Abb. 2).
-Für zwei Tassen starken Kaffee drücken Sie einmal auf die 2-Tassen-Taste (Abb. 3).
Wichtig
Lesen Sie diese Bedienungsanleitung vor dem Gebrauch der Maschine aufmerksam durch, und
bewahren Sie sie für eine spätere Verwendung auf.
Gefahr
-Tauchen Sie die Maschine niemals in Wasser oder andere
Flüssigkeiten.
Warnhinweis
-Prüfen sie, bevor Sie das Gerät anschließen, ob die
Spannungsangabe am Boden des Geräts mit der örtlichen
Netzspannung übereinstimmt.
-Die Netzsteckdose muss schutzgeerdet sein.
18 Deutsch

-Um Gefährdungen zu vermeiden, darf ein defektes Netzkabel nur
von einem Philips Service-Center, einer von Philips autorisierten
Werkstatt oder einer ähnlich qualifizierten Person durch ein
Original-Ersatzkabel ersetzt werden.
-Verwenden Sie die Maschine nicht, wenn der Netzstecker, das
Netzkabel oder die Maschine selbst defekt oder beschädigt ist.
-Dieses Gerät kann von Kindern ab 8Jahren und Personen mit
eingeschränkten physischen, sensorischen oder geistigen
Fähigkeiten oder ohne Erfahrung und besondere Kenntnisse
verwendet werden, wenn sie beim Gebrauch des Geräts
beaufsichtigt werden oder in den sicheren Gebrauch des Geräts
unterwiesen wurden und die verbundenen Gefahren verstanden
haben.
-Reinigung und Pflege dürfen nicht von Kindern durchgeführt
werden, außer sie sind älter als 8 Jahre und werden beaufsichtigt.
-Sorgen Sie dafür, dass Kinder unter 8Jahren keinen Zugang zu
der Maschine, dem Zubehör und zum Kabel der Maschine haben.
-Kinder dürfen nicht mit der Maschine spielen.
Achtung
-Geben Sie das Gerät zur Überprüfung bzw. Reparatur stets an ein
Philips Service-Center. Versuchen Sie nicht, das Gerät selbst zu
reparieren, da die Garantie sonst verfällt.
-Legen Sie die SENSEO® Maschine nach dem Auspacken nie auf
der Seite ab. Halten Sie sie stets aufrecht, auch beim Transport.
-Verwenden Sie keinesfalls normalen gemahlenen Kaffee oder
beschädigte Pads in Ihrer Kaffeepadmaschine, da dies das Gerät
verstopfen würde.
-Aus Sicherheitsgründen darf das Gerät nicht mit einem
Transformator betrieben werden.
-Aus Sicherheitsgründen darf das Gerät nicht mit einem
Transformator betrieben werden.
-Stellen Sie die Maschine auf eine ebene und stabile Fläche.
19
Deutsch

-Stellen Sie die Maschine nicht auf eine Warmhalteplatte, direkt
neben einen heißen Ofen, eine Heizung oder eine ähnliche
Wärmequelle.
-Lassen Sie das eingeschaltete Gerät niemals unbeaufsichtigt.
-Benutzen Sie das Gerät nicht in Höhenlagen von über 2200m.
-Füllen Sie niemals eine andere Flüssigkeit als sauberes kaltes
Wasser in den Wassertank.
-Spülen Sie die Maschine nicht durch, und bereiten Sie keinen
Kaffee zu, solange der Kaffeeauslauf nicht eingesetzt ist.
-Spülen Sie die Kaffeemaschine mit frischem Wasser durch, bevor
Sie sie das erste Mal verwenden. Dabei füllt sich das System mit
Wasser. Dies ist für den ordnungsgemäßen Betrieb der Maschine
entscheidend.
-Verwenden Sie in Verbindung mit Ihrer Kaffeemaschine keine
natriumhaltigen Wasserenthärtungsmittel.
-Entkalken Sie Ihre Maschine regelmäßig. Die Maschine zeigt an,
wenn sie entkalkt werden muss. Wenn Sie dies ignorieren,
funktioniert die Maschine nicht mehr richtig. In diesem Fall ist die
Reparatur von der Garantie ausgeschlossen.
-Verwenden Sie keine Entkalker auf Basis von Mineralsäuren,
beispielsweise Schwefel-, Salz-, Sulfamin- oder Essigsäure (z.B.
Essig). Diese Entkalker könnten Ihre Kaffeepadmaschine
beschädigen.
-Die Maschine ist nur für den normalen Hausgebrauch bestimmt.
Sie ist nicht für die Verwendung in Umgebungen wie z.B.
Personalküchen in Geschäften, Büros, landwirtschaftlichen
Betrieben oder anderen Arbeitsumgebungen vorgesehen.
Weiterhin ist es nicht für den Gebrauch in Hotels, Motels,
Pensionen oder anderen Gastgewerben bestimmt.
-Nehmen Sie die isolierte Thermo-Kanne nicht auseinander.
-Tauchen Sie die isolierte Thermo-Kanne niemals in Wasser oder
eine andere Flüssigkeit, da dadurch Wasser zwischen die Wände
der Thermo-Kanne gelangen kann.
20 Deutsch