Philips SENSEO HD 7810/65 User manual

HD7810/65

1
2
3
4
5
6
7
8
9
10
11
1

HD7810/65
ENGLISH 6

6
IMPORTANT
SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1 Read all instructions.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against electrical shock, do not immerse cords, plugs,
or appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near
children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool
before you putting on or taking off parts.
6 Do not operate any appliance with a damaged cord or plug or after
it malfunctions or has been damaged in any manner.
For assistance, call 1-866-4 Senseo (1-866-473-6736) or visit our
website at www.senseo.us.
7 The use of accessory attachments not recommended by the
manufacturer may cause injuries.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter or touch hot
surfaces.
10 Do not place on or near a hot gas or electric burner, or in heated oven.
11 Extreme caution must be used when moving an appliance containing
hot liquids.
12 To disconnect, turn off by pressing the power button and then remove
plug from wall outlet.
13 Do not use the appliance for other than intended use.
14 This appliance is intended for household use ONLY. It is not intended
for commercial or industrial use.
15 To remove the plug, grip plug body and pull it from the outlet.
Never yank or twist cord to unplug.
16 Do not use this coffee machine if its lid has a cracked, loose, weakened,
or damaged lever.
17 The machine does not work at temperatures below 50ºF/10ºC.
18 Do not use the machine at altitudes higher than 6800ft./2200m above
sea level.
19 Flush the coffee machine with fresh water before you use it for the
rst time (see chapter ‘Preparing the machine for use’). This causes the
system to ll with water, which is essential for the machine to work
properly.
20 Operate the coffee machine on a at, stable surface away from the
edge of the counter to avoid accidental tipping.
21 To prevent scalds and/or property damage, always make sure the
coffee machine lid is securely locked before or during a brewing cycle.
Do not use force when you open or close lid.
22 Do not open lid until coffee machine has nished brewing cycle.
Hot steam or hot water trapped under lid could burn your ngers.
ENGLISH

23 Warning: To reduce the risk of re or electric shock, do not
remove the bottom cover. No user-serviceable parts are
inside. For assistance, call 1-866-4 Senseo (1-866-473-6736)
or visit our website at www.senseo.us.
SAVE THESE
INSTRUCTIONS
SPECIAL INSTRUCTIONS
This coffee machine has a short cord to reduce the hazards of becoming
entangled in or tripping over a longer cord. An extension cord may be
used if the rating is equal to or greater than the rating of the coffee
machine. Use an extension cord rated 13 amperes or greater.Take care
to arrange extension cord so that it does not hang over the edge of
countertop or tabletop, where it can be pulled on by children or tripped
over unintentionally. Operating the coffee machine and another appliance
at the same time from the same electrical circuit could cause an electrical
overload, which would blow the fuse or trip the circuit breaker.
SPECIAL POLARIZED PLUG INSTRUCTIONS
This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to t into a
polarized outlet only one way. If the plug does not t fully into the outlet,
reverse the plug. If it still does not t, contact a qualied electrician. Do not
attempt to modify the plug in any way.
DO NOT ATTEMPTTO DEFEAT THIS SAFETY FEATURE IN
ANY WAY
WARNINGS:
- To avoid risk of personal injury or damage to property as a result of
overow, be sure that the cup or mug is centered under the coffee
outow unit during the brewing cycle.
- Brewed coffee and coffee pods are very hot. Handle with care to avoid
scalding.
- If coffee outow unit overows or fails to drain into cup/mug
during the brewing cycle, do not open lid or handle coffee outow unit
or coffee pod holder(s). Unplug coffee machine and wait for contents
to cool before you handle them.
- Do not remove any part of coffee machine or cup/mug during the
brewing cycle as scalding could occur.
- Use only fresh, cool water in this machine. Do not put any other liquids
in this machine except as instructed in chapter ‘Descaling’. Do not rell
the water reservoir with hot water or coffee.
- DO NOT attempt to move coffee machine during the brewing
process. Let appliance cool down completely before you move it.
- Keep machine at least 4 inches away from walls or other objects while
it operates. Do not place any object on top of coffee machine while it
operates.
PLEASE READ AND SAVE THIS INSTRUCTION MANUAL.
ENGLISH 7

Features (Fig. 1)
1 Water reservoir
2 1-cup pod holder °
3 2-cup pod holder °°
4 Cover of coffee outow unit
5 Coffee outow unit
6 Cup tray
7 Drip tray
8 Indicator light
9 Outow valve
10 Sealing ring
11 Water distribution disc
Introduction
With this Senseo®coffee machine you can enjoy a perfect cup of
coffee - topped with a rich frothy coffee layer - whenever you feel like it.
Each cup is freshly brewed, so you’re always sure of that pure, smooth
taste.The patented Senseo brewing system in combination with the special
Senseo coffee pods makes sure you get only the very best in avor and
aroma from freshly roasted coffee.To optimize the taste of the coffee, you
should keep the following aspects in mind:
Clean cold water
Use clean cold water every day. If you have not used the coffee machine
for three days, you have to ush it with clean cold water before you use it
again (see section ‘Flushing’ in chapter ‘Cleaning’).
Fresh coffee pods
Use the Senseo®coffee pods that have been specially developed for your
Senseo®coffee machine for a full, round taste. Senseo®coffee pods stay
fresh longer when you store them in a storage container.
A clean machine
Clean and descale the Senseo®coffee machine regularly (see chapters
‘Cleaning’ and ‘Descaling’). Remove used coffee pods after brewing.
If a used pod has been left in the coffee machine and you have not used
the machine for some time, ush the machine before you use it again
(see section ‘Flushing’ in chapter ‘Cleaning’).
ENGLISH8

First use
Unpacking
1 Remove the machine from the box.
Note: Make sure you store the 2-cup pod holder in a safe place. It is an
essential part of the machine.
Flushing the machine to ll the system
You cannot brew coffee if you have not ushed the coffee machine rst!
The ushing cycle causes the system to ll with water. After this, the coffee
machine is ready for use.
Flush the machine in the following way:
1 Remove the water reservoir.
2 Fill the water reservoir with clean cold water up to the
MAX indication and put it back onto the machine.
3 Move the lever upwards to release the lid.
4 Open the lid.
ENGLISH 9

5 Put the 1-cup pod holder ° or the 2-cup pod holder °° in the
machine without pod(s).
6 Close the lid and lock the lever.
Note: Make sure you lock the lever properly. Push it down until it snaps home
with a click.
Note: Never ush the machine with the lid open. The lid must be properly
locked.
7 Put the plug in a grounded electrical outlet.
8 Put a bowl with a capacity of at least 1.6 qt (1.5 liters) under the
coffee outow unit to collect the water.
9 Press the on/off button I to turn on the machine. Then press the
1-cup button q and the 2-cup button qq briey at the same time.
,The system lls itself with water from the water reservoir. This takes
some time (approx. 90 to 150 seconds). The machine turns off
automatically when the ushing cycle ends. During the ushing cycle,
the machine produces more noise than during a regular brewing cycle.
Note: Before you use the machine for the rst time, clean the coffee outow
unit and the pod holders with hot water and some washing-up liquid or in the
dishwasher. Clean the water reservoir thoroughly in hot water, if necessary with
some washing-up liquid.
Now your coffee machine is ready for use.
A
B
ENGLISH10

Brewing coffee
1 Fill the water reservoir with clean cold water up to the MAX
indication and put it back onto the machine.
Never pour any other liquid than clean cold water into the water
reservoir.
- MIN: minimum amount of water required to brew 1 cup of coffee.
- A full reservoir allows you to make coffee a number of times.
This makes it unnecessary to ll the water reservoir each time you
want to make a cup of coffee.
2 Press the on/off button Ito turn on the machine.
The indicator light ashes while the water heats up. Heating up takes
approx. 90 seconds.
,The coffee machine is ready for use when the indicator light lights up
continuously.
3 Move the lever upwards to release the lid.
4 Open the lid.
5 Place the Senseo® coffee pod(s) properly in the center of the pod
holder, with the convex side pointing downwards.
,Place one Senseo® coffee pod in the 1-cup pod holder °to brew
one cup of coffee.
,Place two Senseo® coffee pods in the 2-cup pod holder °° to
brew two cups of coffee.
Note: Use Senseo®coffee pods specially designed for your Senseo®coffee
machine for a full and round taste.
Note: Make sure the pod holder is clean and the sieve in the center is not
clogged, e.g. with loose coffee grounds.
Note: Make sure the coffee in the pod(s) is evenly distributed and press the
pod(s) lightly into the pod holder.
ENGLISH 11

6 Close the lid and lock the lever.
Always make sure the lid is properly locked. Push down the lever until it
snaps home with a click.
Never start brewing with the lid open. The lid must be properly closed.
7 Place one cup or two cups under the coffee outow unit.
The cups you use should have a capacity of at least 5.0.oz. (150ml).
Do not use cups that are too large, as they cause the coffee to get cold
more quickly.
8 Press the button that indicates the number of cups of Senseo®coffee
you want to brew.
- Press the 1-cup button qfor one cup.
- Press the 2-cup button qq for two cups.
,The coffee machine starts brewing.
- The machine automatically supplies the optimal amount of water.
Do not remove the water reservoir during a brewing cycle,
as this will cause the machine to draw in air.
Tip: You can interrupt the brewing cycle at any time. To do this, press the same
cup button (1-cup button q or 2-cup button qq) that you pressed to start
brewing coffee. However, if you do this, the machine does not complete the
interrupted brewing cycle if you turn it on again or press the same cup button
again.
9 After use, lift the pod holder out of the machine and remove the
coffee pod(s).
Be careful when you do this, for there may still be some water/coffee on
the coffee pod(s).
10 After use, press the on/off button 3to turn off the machine.
Note: If you do not use the machine, it turns off automatically after 30 minutes
to save energy.
Note: Never put normal ground coffee or use torn pods in the
coffee machine, as this causes it to become blocked.
ENGLISH12

Cleaning the machine
Never immerse the coffee machine in water or any other liquid.
Never clean the machine by ushing it with the lid open.
Cleaning the coffee machine
1 Always turn machine off and unplug the machine before you clean it.
2 Clean the outside of the machine with a moist cloth.
3 Remove the coffee outow unit.
,You can disassemble the coffee outow unit for more thorough
cleaning.
4 Clean the coffee outow unit, the pod holders, the drip tray, the cup
tray and the water reservoir in hot water, if necessary with some
washing-up liquid, or in the dishwasher.
5 To prevent clogging, clean the pod holders regularly with hot water,
some washing-up liquid and a washing-up brush. If you have used
the 2-cup pod holder to brew cappuccino or hot chocolate, make
sure to clean it thoroughly immediately after use to remove any milk
residues.
Note: Use the clogged pod holder in the machine during descaling to clean it
even more effectively.
6 Clean the water distribution disc with a moist cloth.
Be careful when you do this. Make sure that the rubber sealing ring does
not get stuck under the edge of the water distribution disc. If it does,
the coffee machine starts to leak.
ENGLISH 13

Flushing the coffee machine
If you have not used the coffee machine for three days, ush it with clean
cold water before you use it again.
Flush the machine in the following way:
1 Fill the water reservoir with clean cold water up to the MAX
indication and put it back onto the machine.
2 Put the 1-cup pod holder ° or the 2-cup pod holder °° in the
machine without pod(s).
3 Put a bowl with a capacity of at least 1.6 qt (1.5 liters) under the
coffee outow unit to collect the water.
4 Press the on/off button I. Wait until the machine has heated up.
Then press the 2-cup button qq several times until the water
reservoir is empty.
ENGLISH14

Descaling
When to descale
Descale the Senseo® coffee machine frequently. Preferably descale 4 to
6 times a year, but at least once every 3 months.There is no difference
between soft-water and hard-water areas in this respect. Descaling takes
about 1 hour. Do not interrupt the descaling process.
Why to descale
Scale builds up inside the machine during use. It is essential to descale the
coffee machine at least every 3 months.Your reasons to descale:
- It prolongs the life of your coffee machine
- It ensures maximum cup volume
- It ensures maximum coffee temperature
- The machine produces less sound during brewing
- It prevents malfunctioning
If the descaling procedure is not performed correctly, scale residue remains
behind in the machine.This causes scale to build up more quickly and may
cause permanent and irreparable damage to the machine.
Use the correct descaler
Only citric acid-based descalers are suitable for descaling the Senseo®
machine.This type of descaler descales the machine without damaging it.
For the correct amount, see under ‘Descaling procedure’ below.
Each descaling mixture can be used only once. Use a new descaling
mixture each time.
Never use a descaler based on mineral acids such as sulphuric acid,
hydrochloric acid, sulphamic acid and acetic acid (e.g. vinegar).
These descalers may damage your Senseo®coffee machine.
Descaling procedure
The descaling procedure consists of 2 descaling cycles, each with 1 quart
(1 litre) of descaling mixture, and 2 ushing cycles. Do not interrupt the
descaling cycles and do not turn off the machine before or between the
ushing cycles.
1 Press the on/off button Ito turn on the machine.
2 Place the 1-cup pod holder ° with a used coffee pod in it in the
coffee machine. Close the lid and make sure it is properly locked.
3 Mix the descaler powder with 1 quart (1 litre) of water in a
measuring jug. Stir until the powder is completely dissolved.
4 Fill the water reservoir up to the MAX indication with the descaler
mixture.
Note: If your coffee machine has a water reservoir with a capacity of less than
1 quart (1 litre), you have to repeat steps 4 to 7 with the remainder of the
mixture with the remaining descaler mixture.
5 Put the water reservoir back into the coffee machine. The machine is
ready for use when the indicator light lights up continuously.
6 Put a bowl with a capacity of at least 1.6 qt (1.5 liters) under the
coffee outow unit to collect the descaling mixture.
ENGLISH 15

7 Press the 2-cup button qq and let the machine operate. Repeat this
until the water reservoir is empty.
Note: Make sure that you use up the descaling mixture completely during the
descaling cycle.
Never interrupt the descaling cycle.
8 Exchange the 1-cup pod holder ° for the 2-cup pod holder °°.
Place a used pod in the 2-cup pod holder °° and close the lid.
9 Repeat steps 3 to 7.
Never descale the coffee machine with the lid open. Make sure the lid is
properly locked.
10 Remove the used pod and clean both pod holders after descaling
with hot water and a dishwashing brush to prevent the sieve in the
center from getting clogged.
11 Rinse the water reservoir with clean cold water. Fill the water
reservoir up to the MAX indication with clean cold water and repeat
steps 5 to 7.
Note: Do not rell the water reservoir with used hot water or the used
descaling mixture.
12 Rinse the water reservoir once again with clean cold water. Fill the
water reservoir with clean cold water up to the MAX indication and
repeat steps 5 to 7 once more.
Note: Always rinse the machine by letting it empty two full water reservoirs.
Frost-free storage
If the coffee machine has already been used and therefore has been
ushed with water, it may only be used and stored in a frost-free place to
prevent it from becoming damaged.
Assistance
For assistance, call 1-866-4 Senseo (1-866-473-6736) or visit our
website at www.senseo.us.
Disposal
This product may contain lead and mercury. Disposal of these materials
may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or visit
www.recycle.philips.com.
ENGLISH16

Warranty
Atlantic Coffee Solutions LLC (ACS) hereby warrants that, if your
SENSEO®Single Serve Gourmet Coffee Maker Model HD7810/65
(except cord, coffee pods and accessories) is found to be defective in
materials or workmanship during the period of one year from the date of
purchase, ACS will, at its option, either (1) repair or replace any defective
product without charge to you, or (2) refund your purchase price.
This warranty extends only to the original retail purchaser.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the afxing of any
attachment not provided with the product, loss of parts, or subjecting the
product to any but the specied voltage. Use of unauthorized replacement
parts will also void this warranty. ACS will not pay for warranty service
performed by a non-authorized repair service.
In order to obtain warranty service, call our SENSEO®Consumer Affairs
Hotline at 1-866-473-6736.You will need proof of purchase to obtain a
warranty remedy.
REPAIR, REPLACEMENT OR REFUND (AT THE OPTION OF ACS)
IS YOUR ONLY REMEDY UNDER THE ABOVE WARRANTY. ACS SHALL
NOT BE LIABLE FOR ANY OTHER INCIDENTAL, CONSEQUENTIAL
OR INDIRECT COSTS, EXPENSES OR DAMAGES
NO OTHER WARRANTY,WRITTEN OR ORAL, IS AUTHORIZED BY
ACS. ALL IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF
THE APPLICABLE WRITTEN WARRANTY ABOVE.
Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations and exclusions may not
apply to you. This warranty gives you specic legal rights, and you may also
have other rights which may vary from state to state.
Read the instructions enclosed with your Senseo coffee machine carefully.
Manufactured for:
Atlantic Coffee Solutions LLC
3900 Harrisburg Blvd
Houston,TX 77003
Call 1-866-4 Senseo (1-866-473-6736) or visit our website: www.senseo.us.
SENSEO®is a registered trademark.
Troubleshooting
If you experience a problem with your coffee machine, you may nd the
solution in the table below. If the table does not provide the solution to
your problem or if you have a question, call 1-866-4 Senseo
(1-866-473-6736) or visit our website at www.senseo.us.
ENGLISH 17

Problem Cause Solution
My coffee cup
overows with
cold coffee.
You did not ush the
machine before rst use.
Flush the machine before rst use. When the machine
has emptied a complete water reservoir, you can start
to make a new coffee.
The indicator light
ashes slowly.
The machine is heating
up.
If this takes longer than two minutes, call 1-866-4
Senseo (1-866-473-6736) or visit our website at
www.senseo.us.
The indicator light
ashes quickly.
There is not enough
water in the water
reservoir.
Fill the water reservoir and make sure you place the
water reservoir properly into the machine.
The oat in the water
reservoir may be stuck.
Empty the water reservoir and shake it a few times to
release the oat. Clean the water reservoir with hot
water and some washing-up liquid or in the dishwasher.
If these solutions do not solve the problem, call
1-866-4 Senseo (1-866-473-6736) or visit our website
at www.senseo.us.
The coffee is not
hot enough.
You have used the
machine for a longer
period without descaling.
Perform the descaling procedure as described in
chapter ‘Descaling’.
The coffee
temperature in
the cup decreases
quickly.
Do not use cups that are
too large.
Use thin-walled cups.Thin-walled cups absorb less heat
from the coffee than thick-walled cups.
You can preheat the coffee machine and cup by
brewing a cup of hot water rst without placing a
coffee pod in the pod holder.
I cannot open
the lid.
A temporary vacuum has
developed under the lid.
Turn off the coffee machine. Pull up the lever and wait
24 hours before you open the lid.You may need to
use some force. Always make sure the pod holders are
clean and the sieve is not clogged to prevent vacuum.
The coffee
machine produces
less coffee than
before.
Perhaps the sieve in the
center of the pod holder
is clogged.
If the sieve is clogged, use a washing-up brush to
unclog the sieve. If you cannot unclog it properly
with the dishwashing brush, put the pod holder in
the machine and descale the machine. Descale the
machine (see chapter ‘Descaling’).
I cannot close the
lid properly.
Perhaps a used coffee
pod is sticking to the
water distribution disc.
If this is the case, remove the used pod.
ENGLISH18

Problem Cause Solution
The coffee is not
strong enough.
You may not have used
the right number of pods
or may have pressed the
wrong button.
Use 1 pod in combination with the 1-cup pod holder
and the 1-cup button. Use 2 pods in combination with
the 2-cup pod holder and the 2-cup button.
The pod(s) may not have
been placed in the pod
holder properly.
Place the coffee pod(s) properly in the center of the
pod holder, to prevent water from escaping along the
edge of the pod(s).When you use two coffee pods on
top of each other, make sure that the convex sides of
both pods point downwards and press the pods lightly
into the pod holder. Make sure that the coffee in the
pod is distributed evenly.
You may have used the
same pod twice.
Place a new pod in the pod holder to brew a fresh cup
of coffee.
Perhaps you need a
different avor.
If you prefer a more robust avor, Senseo®coffee pods
with a stronger blend are available.
The coffee is too
strong.
Perhaps you need a
different avor.
If you prefer a milder avor, Senseo®coffee pods with
a milder blend are available.
Water leaks
from the coffee
machine.
You have not closed the
lid properly.
Close the lid properly and lock the lever.
You overlled the water
reservoir.
Do not ll the water reservoir beyond MAX level.
The sieve in the center
of the pod holder may
be clogged.
Check the pod holder. If the sieve is clogged, use a
dishwashing brush to unclog the sieve. If you cannot
clean it properly with the dishwashing brush, put the
pod holder in the machine and descale the machine
(see chapter ‘Descaling’).
The sealing ring may be
stuck under the edge of
the distribution disc.
Check if the sealing ring is stuck under the edge of
the distribution disc. If it is, pull it out from under the
distribution disc carefully.
The machine has been
stored in a room that
was not frost-free.
For assistance, call 1-866-4 Senseo (1-866-473-6736)
or visit our website at www.senseo.us.
Water drops on the
worktop may be the
result of placing the
water reservoir or
removing and removing
used pod(s).
Check if the water drops on the worktop are not the
result of placing or removing the water reservoir or
removing used coffee pods. Make sure that you do not
remove the water reservoir when the coffee machine
is heating up.This may cause water that normally ends
up in the water reservoir to leak out of the machine.
I
n all other cases, call 1-866-4 Senseo
(1-866-473-6736) or visit our website at www.senseo.us.
ENGLISH 19