Philips CD3653Q/37 User manual

Register your product and get support at
www.philips.com/welcome
Quick Start Guide
CD360
CD365
1
2
3
CD360-365_37_QSG_EN_V3.0Printed in China
Connect
Install
Enjoy
Start/Stop playback: Press play/stop.•
Adjust the volume: Press• / .
Skip backward:
•
During message playback, press to play the message from the beginning.
During the first second of the current message, press to play the
previous message.
Skip forward: Press
• to skip to the next message.
Delete the current message: Press
• erase.
Listen to messages recorded on the answering machine
(for CD365 only)
Note
For more information, see the Telephone answering machine section•
in the user manual.
Troubleshooting
Welcome to Philips
Need help?
Check your phone connections.•
The handset is out of range. Move it closer to the base station.
The signal icon flashes.
The handset is out of range. Move it closer to the base station.•
If the handset displays [UNREGISTERED], register the handset.
The caller ID does not display.
The service is not activated. Check with your service provider.•
The caller’s information is withheld or unavailable.
For more information, see the User Manual.
No dialing tone
Register your product at www.philips.com/welcome
Refer to the User Manual that came with your new phone.
www.philips.com/support
© 2009 Koninklijke Philips Electronics N.V. All rights
reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner.
Trademarks are the proper ty of Koninklijke Philips
Electronics N.V. or their respective owners.
User Manual
Online help
0168

What’s in the box
Handset
Base station with
bracket for CD360
OR
CD365
User manual
Power supply
Belt clip
Guarantee
Line cord*
Quick Start Guide
Note
Caution
In some countries, you have to connect the line adaptor to the line cord, then•
plug the line cord to the line socket.
In multi-handset packs, there are additional handsets and chargers with power
•
supply units.
Use only the supplied batteries and adaptor
•
13
2
Connect Enjoy
Install
Connect the base station
Install the handset
1 Connect the output plug of the power socket to the bottom of the base station.
2 Connect the power socket to a standard wall outlet.
3 Connect the telephone line cord to the phone socket at the bottom of the base
station and the wall phone socket.
1 Press
flash
TAL
K
and dial the phone number; or
2 Dial the phone number and press flash
TAL
K
to dial out the call.
1 Press
Ph.Boo
k
to access the phonebook.
2 Select a contact in the phonebook list.
3 Press
flash
TAL K to make the call.
1 Press menu.
2 Select [PERSONAL SET] > [HANDSET TONES] > [RING TONES],
then press [OK] to confirm.
3 Select a ringtone, then press [OK] to confirm.
The setting is saved.»
1 Press menu.
2 Select [PHONEBOOK] > [NEW ENTRY], then press [OK]
to confirm.
3 Enter the name then press [OK] to confirm.
4 Enter the number, then press [OK] to confirm.
When the phone rings, press flash
TAL
K
or to answer the call.
Press exit
END .
Press call ID or Ph.Boo
k
to adjust the volume during a call.
1 The batteries are pre-installed in the handset. Pull the battery tape off from
the battery door before charging.
2 Place the handset on the base station to power up.
CD365
Make a call
Call from the phonebook
Set the handset’s ringtone
Add a record
Answer a call
End a call
Adjust the earpiece volume
Note:
Charge the batteries for 24 hours before first use.
For more information on the battery icon status, see the User Manual.