Philips D450 Product information sheet

D450
D455
Register your product and get support at
www.philips.com/support
Short user manual
05.en V. UK adaptor

Warning
• The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
accessible.
• Refer to safety information before using the product.
• This product complies with European R&TTE
directive 1999/5/EC.
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact
with liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
Important safety
instructions

1Overview
In call
Enter the option menu.
Change the sound prole.
Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/off.
Mute/unmute the microphone.
In menu
Conrm / Select / Enter the option menu.
Cancel / back
Up / down
Exit menu.
Standby
Access the main menu.
Access the redial list.
Phonebook
Call log
Make and receive calls.
Switch the handset on or off (press and hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
D455 only: Press to play new message from the
answer machine. / Access to the answer machine
menu.
In text input
Delete text.
Enter a space.
Switch upper/lower case (press and hold).
Microphone
Earpiece
Loudspeaker
(back side)
Display icons
D455D450
/
/
Loudspeaker
Find handset
(bottom)
Display icons
It shows the connection status between the
handset and base station.The more bars are
shown, the better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It remains steadily on when browsing outgoing
calls in the redial list.
It ashes when there is a new missed call or
when browsing unread missed calls in call log. It
remains steadily on when only old call log exists
or when browsing the read missed calls in call
log.
It remains steadily on when browsing blocked
calls in call log.
It ashes when receiving incoming call. It remains
steadily on when you are in a call.
The alarm is activated.
The silent mode is set, but is outside of active
period.
The speaker is on.
The ringer is off.
The silent mode is set and within active period
(the phone does not ring).
D455 only: Answering machine: it ashes when
there is a new message or when the memory is
full. It is displayed when the telephone answering
machine is turned on.
Voice messages indicator: ashes for new
messages, is steady for reviewed messages.
* This is network dependent.
It is displayed when you scroll up/down a list or
increase and decrease the volume.
The Eco mode is activated.
The ECO+ mode is activated.

1 2 1 2
3
D455 D450
2Connect
Multi-handset version only.

3Get started
Insert batteries Charge your phone
Charge 8 hours
Congure your phone
1 When using your phone for the rst time, you see
a welcome message (country dependent).
2 Set the country and language if prompted.
3 Set the date and time.
• If the time is in 12-hour format, press / to
select [am] or [pm] (country dependent).
> 70%
40% - 70%
10% - 40%
Flashing: low battery
Scrolling: charging in progress

4Enjoy
Phonebook
Add record
1 Press [Menu].
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
3 Follow on-screen instructions.
Direct access memory
You have up to 2 direct access memories (keys 1
and 2).To dial the saved phone number automatically,
press and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively
(network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
View record
Press > [Option] > [View].
Save record
1 Press > [Option] > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > [Option] > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press [Redial].
2 Select a record and press .
Save record
1 Press [Redial] > [Option] > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press [Redial] > [Option] > [Delete].
2 Follow on-screen instructions.
Record an announcement
(for D455 only)
1 Press [Menu] > [Answ. Machine] >
[Announcement].
2 Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
station.
1 Press [Menu].
2 Select [Services] > [Register], then press
[OK] to conrm.
3 Press and hold on the base station for 5
seconds.
4 Enter the system PIN/passcode (0000).
5 Press [OK] to conrm the PIN/passcode.
» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press [Menu].
2 Select [Services] > [Reset], then press [OK]
to conrm.
3 Follow on-screen instructions.
Note
• You may recall the original PIN/passcode by
following this procedure.

5Learn more
Silent mode
Sets time during which the phone will not ring.
[Phone setup] > [Sounds] > [Silent mode]
MySound
Customizes the sound of voices to your liking.
[Phone setup] > [Sounds] > [MySound]
Eco/ECO+ mode
Reduces transmission power and radiation (causes 2
seconds ring delay, 50% shorter standby time).
[Phone setup] > [Eco mode]/[ECO+ mode]
Call barring
Prevents unwanted outgoing calls to selected
numbers.
[Services] > [Call barring]
Blacklist
Blocks incoming calls to certain undesirable numbers.
[Services] > [Blacklist]

Technical data
Battery
Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter
Base and charger:
Meic:
MN-A102-U130
Philips:
S003IB0600040
Input: 100-240 V~
50/60 Hz 200 mA
100-240 V~
50/60 Hz 150 mA
Output: 6 Vdc 400 mA 6 Vdc 400 mA
Phonebook with 50 entries
Call log with 50 entries
Talk time: 16 hours
Standby time: 250 hours
Note
• You can install a DSL (digital subscriber line) lter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can nd the Declaration of Conformity on
www.p4c.philips.com.

Frequently asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays
[Register your Handset], register your
handset. (See the section on “Register additional
handsets”).
If I fail to pair (register) the additional handsets to
the base station, what do I do?
Your base memory is full. Access > [Services]
> [Unregister] to unregister the unused handsets
and try again.
I have chosen a wrong language which I cannot
read, what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone
connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger.The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply rst and clean the contacts with a
damp cloth.
• Batteries are defective. Purchase new ones with
the same specications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.

www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.

This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
2015 © Gibson Innovations Limited.
All rights reserved.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd.,
and Gibson Innovations Ltd. is the warrantor in
relation to this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.
UMS_D450/455
05_EN_V3.0
WK15173
0168016801680168