Philips DVD VIDEO PLAYER W-MP3 PLAYBACK DVD703AT User manual

1
DVDVideo Player DVD-703
DVD-703
HookupPages

6
English
Functional Overview
FUNCTIONAL OVERVIEW
Front and Rear Panels
PLAY
PREV
STOP
NEXT
SOUND
OPEN
/CLOSE PAUSE
POWER ON/OFF
DVD 703
DVD/VIDEO CD/CD PLAYER
by
POWER ON/OFF
– switches the player to ON or OFF
DISPLAY
– shows the current status of the player
T NEXT
– go to next chapter or track
B PLAY
– to start playback
SOUND
– selects Stereo, Dolby Surround or
3D Sound (TruSurround)
/OPEN/CLOSE
– opens/closes the disc tray
Disc Tray
; PAUSE
– to interrupt playback
S PREV
– go to previous chapter or track
9 STOP
– to stop playback
COAXIAL
DIGITAL AUDIO OUT
PCM-MPEG2-Dolby Digital-DTS
L
R(CVBS)
VIDEO OUT
AUDIO OUT
S-VIDEO
Y
P
B /C B
P R /C R
MAINS (AC Power)
– connect to power source
COAXIAL (Digital audio out)
– connect to digital (coaxial) audio equipment
AUDIO OUT (Left/Right)
– connect to amplifier, receiver or stereo
system
S-VIDEO (VIDEO OUT)
– connect to a TV with S-Video (Y/C) inputs
PR/CRPB/CBY (VIDEO OUT)
– connect to a TV with PR/CRPB/CBY inputs
CVBS (VIDEO OUT)
– connect to a TV with CVBS video inputs
Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause
permanent damage to the unit.

8
English
Preparation
General Notes
¶Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
player. Use only one of the connections described below.
¶Please refer to the manuals of your TV,VCR, Stereo System
or other devices as necessary to make the best
connections.
¶For better sound reproduction, connect the player’s audio
out jacks to the audio in jacks of your amplifier, receiver,
stereo or audio/video equipment. See ‘Connecting to
optional equipment’.
Caution:
–Make sure the DVD player is connected directly
to the TV. Set the TV to the correct video input
channel.
–Do not connect the player’s audio out jack to
the phono in jack of your audio system.
–Do not connect your DVD player to the TV via
your VCR.The DVD image could be distorted by
the copy protection system.
Connecting to a TV
¶Make one of the following connections, depending on the
capabilities of your existing equipment.
ComponentVideo (PR/CRPB/CBY)
connection
1Connect the PR/CR, PB/CB,Y video out jacks on the DVD
player to the corresponding in jacks on the TV using an
optional PR/CR, PB/CB,Y cable (Z).
2Connect the Left and Right audio out jacks of the DVD
player to the audio left/right in jacks on the TV (A).
S-Video (Y/C) connection
1Connect the S-Video video out jack on the DVD player to
the S-Video in jack on the TV using an optional S-Video
cable (Y).
2Connect the Left and Right audio out jacks of the DVD
player to the audio left/right in jacks on the TV (A).
CVBS connection
1Connect the CVBS video out jack on the DVD player to
the video in jack on the TV using the video cable supplied
(X).
2Connect the Left and Right audio out jacks to the audio
left/right in jacks on the TV (A).
TV
YXA Z
COAXIAL
DIGITAL AUDIO OUT
PCM-MPEG2-Dolby Digital-DTS
L
R(CVBS)
VIDEO OUT
AUDIO OUT
S-VIDEO
Y
P
B /C B
P R /C R
Connecting to Optional
Equipment
Connecting to an amplifier equipped with
two channel analog stereo or Dolby
Surround
1Connect the Left and Right audio out jacks of the DVD
player to the audio left and right in jacks on your amplifier,
receiver or stereo system, using the supplied audio cable
(A).
Connecting to an amplifier equipped with
two channel digital stereo (PCM) or to an
Audio/Video receiver equipped with a
multi-channel decoder (Dolby Digital™,
MPEG 2 or DTS)
1Connect the player’s coaxial digital audio out jack to the
corresponding coaxial digital audio in on your amplifier. Use
an optional digital audio cable (F).
2You will need to activate the player’s digital output (see
‘Personal Preferences’).
Digital Multi-channel sound
The digital multi-channel connection provides the best
sound quality. For this you need a multi-channel Audio/
Video receiver that supports one or more of the audio
formats supported by your DVD player (MPEG 2, Dolby
Digital™ or DTS). Check the receiver manual and the logos
on the front of the receiver.
PREPARATION

9
English
TV
Y
X
Z
COAXIAL
DIGITAL AUDIO OUT
PCM-MPEG2-Dolby Digital-DTS
L
R(CVBS)
VIDEO OUT
AUDIO OUT
S-VIDEO
Y
P
B /C B
P R /C R
AMPLIFIER
A
F
Note:
– If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital connection
can only be obtained if your receiver has a Digital Multi-
channel decoder.
– To see the selected audio format of the current DVD in the
StatusWindow, press SYSTEM MENU or Audio.
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to
match the video signal of yourTV.This setting only affects
the television’s on-screen display that shows the stop and
setup modes.You may select either NTSC or PAL.To
change the DVD player setting to PAL or NTSC, follow the
steps below.
1Press the POWER ON/OFF button on the front panel of
the DVD player to turn OFF the DVD player.
2Press and hold 9and Ton the front of the DVD player.
While holding 9and Tpress POWER ON/OFF.
3After PAL or NTSC appears on the display panel of the
DVD player, release 9and Tat the same time.The PAL
or NTSC indicator that appears on the display panel
indicates the current setting.
4To change the setting, press Twithin three seconds.The
new setting (PAL or NTSC) will appear on the display
panel.
General explanation
About this manual
This manual gives the basic instructions for operating the
DVD player. Some DVDs require specific operation or
allow only limited operation during playback.When this
occurs, the symbol Äappears on the TV screen, indicating
that the operation is not permitted by the player or the
disc.
Remote control operation
¶Unless stated, all operations can be performed by the
remote control. Always point the remote control directly at
the player, making sure there are no obstructions between
the remote and the player.
Corresponding keys on the front panel of the player can
also be used.
Menu bar operation
¶A number of operations can be done with the menu bar
on the screen.The menu bar can be accessed by pressing
the cursor keys on the remote control.
¶Pressing SYSTEM MENU while the menu bar is displayed
will clear the menu bar from the screen.
¶The selected item will be highlighted, and the appropriate
cursor keys to operate it will be displayed below the icon.
¶The symbols < or > indicates that more items are available
at the left/right of the menu bar. Press 1or 2to select
these items.
PREPARATION