Philips BDP7300 User manual

BDP7300
BDP5000
Register your product and get support at
www.philips.com/welcome
EN User Manual 5
Downloaded From Disc-Player.com Philips Manuals

2
Important notes for users in U.K.
Mains plug
This apparatus is fitted with an approved
moulded plug. Should it become necessary to
replace the main fuse, this must be replaced with
a fuse of same value as indicated on the plug
(example 10A).
Remove fuse cover and fuse.1.
The replacement fuse must comply with2.
BS1362 and have the A.S.T.A. approval
mark. If the fuse is lost, contact your dealer
in order to verify the correct type.
Ret the fuse cover.3.
In order to maintain conformity to the EMC
directive, the mains plug on this product must
not be detached from the mains cord.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er derfor
ikke frakoplet nettet så lenge apparatet er
tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio BDP7300,
BDP5000, Philips risponde alle prescrizioni
dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n.
548.
Fatto a Eindhoven
Philips Consumer Lifestyles
Philips, Glaslaan 25616 JB Eindhoven,
The Netherlands
LASER
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION:
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK DEFEATED.
DO NOT STARE INTO BEAM.
LOCATION:
INSIDE, NEAR THE DECK MECHANISM.
CLASS 1
LASER PRODUCT
Downloaded From Disc-Player.com Philips Manuals

3
DK
Advarsel: Usynlig laserstråling ved åbning når
sikkerhedsafbrydere er ude af funktion. Undgå
utsættelse for stråling.
Bemærk: Netafbryderen er sekundært indkoblet
og ofbryder ikke strømmen fra nettet. Den
indbyggede netdel er derfor tilsluttet til lysnettet
så længe netstikket sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat sätt än
i denna bruksanvisning specificerats, kan
användaren utsättas för osynlig laserstrålning,
som överskrider gränsen för laserklass 1.
Observera! Stömbrytaren är sekundärt kopplad
och bryter inte strömmen från nätet. Den
inbyggda nätdelen är därför ansluten till elnätet
så länge stickproppen sitter i vägguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen muulla kuin tässä
käyttöohjeessa mainitulla tavalla saattaa altistaa
käyttäjän turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei saa olla
alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-osa on
kytkettynä sähköverkkoon aina silloin, kun
pistoke on pistorasiassa.
Downloaded From Disc-Player.com Philips Manuals

4EN
HDMI, and HDMI logo and
High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI
licensing LLC.
Windows Media and the
Windows logo are trademarks or registered
trademarks of Microsoft Corporation in the
United States and/or other countries.
The USB-IF logos are trademarks
of Universal Serial Bus Implementers Forum, Inc.
DivX, DivX Ultra
Certified, and associated logos are trademarks
of DivX, Inc. and are used under license.
Official DivX® Ultra Certified product. Plays all
versions of DivX® video (including DivX®
media files and the DivX® Media Format.
‘DVD-VIDEO’ is a trademark of DVD
Format/Logo Licensing Corporation.
‘Blu-ray Disc’ and are trademarks.
Manufactured under license
from Dolby Laboratories. Dolby and the
double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and
worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos,
Symbol, DTS-HD and HTS-HD Master Audio |
Essential are trademarks of DTS, Inc. ©
1996-2008 DTS, Inc. All Rights Reserved.
(DTS-HD Master Audio Essential for model
BDP7300 only)
(DTS 2.0+Digital Out for model BDP5000
only)
Java and all other Java trademarks and
logos are trademarks or registered trademarks
of Sun Microsystems, Inc. in the United States
and/or other countries.
‘BD LIVE’ and
‘BONUSVIEW’ are trademarks of Blu-ray Disc
Association.
‘AVCHD’ and the ‘AVCHD’
logo are trademarks of Matsushita Electric
Industrial Co., Ltd and Sony Corporation.
(AVCHD for model BDP7300 only)
’x.v.Colour’ is a trademark of
Sony Corporation.
Downloaded From Disc-Player.com Philips Manuals

English
EN 5
Contents
Contents
1 Important 6
Safety and important notice 6
2 Your product 7
Features highlight 7
Product overview 9
3 Connect 12
Connect video/audio cables 12
Route audio to other devices 14
Connect USB device 15
Connect LAN 15
Connect power cord 16
4 Get started 17
Insert the remote control batteries 17
Find the correct viewing channel 17
Use the Home menu 18
Select menu display language 18
Set up network 18
Use Philips EasyLink 19
5 Play 20
Play a disc 20
Play video 21
Play music 25
Play photo 26
Play from USB device 27
6 Adjust settings 28
Video Setup 28
Audio Setup 30
Preference Setup 31
EasyLink Setup 33
Advanced Setup 34
7 Additional information 36
Update software 36
Care 36
Specifications 37
8 Troubleshooting 38
9 Glossary 40
Downloaded From Disc-Player.com Philips Manuals

6EN
Recycle notice
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
1 Important
Safety and important notice
Warning!
Risk of overheating! Never install this product in a• confined space. Always leave a space at least four
inches around the product for ventilation. Ensure
curtains or other objects never cover the ventilation
slots on the product.
Never place the product, remote control or
• batteries near naked flames or other heat sources,
including direct sunlight,
Only use this product indoors. Keep this product
• away from water, moisture and liquid-filled objects.
Never place this product on other electrical
• equipment.
Keep away from this product during lightning storms.
• Where the mains plug or an appliance coupler is• used as the disconnect device, the disconnect device
shall remain readily operable.
Visible and invisible laser radiation when open.
• Avoid exposure to beam.
This product complies with the radio
interference requirements of the European
Community. This product complies with the
requirements of the following directives and
guidelines: 2004/108/EC , 2006/95/EC.
Downloaded From Disc-Player.com Philips Manuals

English
EN 7
Your product
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
2 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Features highlight
Philips EasyLink
Your Blu-ray disc player supports Philips
EasyLink, which uses the HDMI CEC
(Consumer Electronics Control) protocol.
EasyLink-compliant devices that are connected
through HDMI connectors can be controlled by
a single remote control.
High-Definition entertainment
Watch high-definition content disc with the
HDTV (High Definition Television), connect it
through a high speed HDMI cable (1.3 or
category 2). You can enjoy excellent picture
quality up to 1080p resolution with the frame
rate of 24 frames per second with progressive
scan output.
High fidelity 5.1 channel surround sound
This Blu-ray disc player supports the high-
definition audio such as Dolby Digital Plus,
Dolby TrueHD and DTS-HD Master Audio.
To make the most of their high performance,
connect the BDP7300 to an analogue
5.1-channel AV receiver/amplifier and speakers
for full 5.1-channel surround sound.
Downloaded From Disc-Player.com Philips Manuals

8EN
BONUSVIEW/PIP (Picture-In-Picture)
This is a new function of BD-Video that plays
the primary video and secondary video
simultaneously. Blu-ray players with Final
Standard Profile or Profile 1.1 specs can play
Bonus View features.
BD-Live
Connect this Blu-ray disc player to the movie
studios website via the LAN port to access a
variety of up-to-date content (e.g., refreshed
previews and exclusive special features). You
can also enjoy next generation possibilities, such
as ringtone/wallpaper downloads, peer-to-peer
interactions, live events and gaming activities.
Upscale DVD for enhanced picture quality
Watch the discs in the highest picture quality
available for the HDTV. Video upscaling
increases the resolution of standard definition
disc to high definition up to 1080p over an
HDMI connection. A highly detailed picture
and increased sharpness delivers a more
true-to-life picture.
Region codes
You can play discs with the following region
codes.
Region Region code
Europe,
United
Kingdom
DVD BD
ALL
2
Asia Pacific,
Taiwan,
Korea
ALL
3
A
Latin America
ALL
4
A
Australia,
New Zealand
ALL
4
Russia, India
ALL
5
C
China
ALL
6
C
Downloaded From Disc-Player.com Philips Manuals

English
EN 9
Your product
Product overview
Remote control
a2 (Standby-On)
T• urns on this player or switches to
standby mode.
W• hen EasyLink is enabled, switches the
Blu-ray disc player and all EasyLink
devices to standby. Note that you
must press and hold 2(Standby-On)
for at least 3 seconds for this to occur.
bBONUSVIEW
Turns on of off the secondary video in• a small screen window during play
(applicable only to BD-Video that
supports the BONUSVIEW or
Picture-in Picture feature).
cTOP MENU
BD• : Displays the top menu.
DVD• : Displays the title menu.
d(Home menu)
Accesses the home menu.•
eDISC MENU / POP-UP MENU
BD:• Accesses or exits the pop-up
menu.
DVD:• Accesses or exits the disc menu.
fOKConfirms an entry or selection.•
gSTW X(Navigation buttons)
Navigates through the menus.•
hBACK 2
Returns to the previous screen.•
ií ë (Previous / Next)
Skips to the beginning of the current• title or chapter. Press twice to return
to the previous title, chapter or track.
Skips to the next title, chapter or track.•
jmM(Backward / Forward)
Searches fast-forward or fast-backward.•
Downloaded From Disc-Player.com Philips Manuals

10 EN
kH(Mute)
Mutes or restores TV audio (applicable• only to PHILIPS brand TV).
lA+-
Increases or decreases TV volume• (applicable only to PHILIPS brand TV).
mSUBTITLE
Selects a subtitle language on a disc.•
nAUDIO
S• elects an audio language or channel
on a disc.
oAlphanumeric buttons
Selects an item to play.• Enters values or letters (using SMS style• entry).
pZ(Open/Close)
O• pens or closes the disc compartment.
qTV CH +-
Selects a TV channel (applicable only to• PHILIPS brand TV).
rx(Stop)
S• tops play.
sX(Pause)
Pauses play.• Moves the paused picture one step• forward.
tB(Play)
Starts or resumes play.•
uINFO
Displays the current status or disc• information.
vOPTIONS
Accesses or exits the play options• menu.
wColour buttons
BD• : Selects tasks or options.
xHDMI
Selects HDMI video resolution setting.•
yREPEAT
Selects or turns off repeat or shuffle• mode.
Downloaded From Disc-Player.com Philips Manuals

English
EN 11
Your product
Main unit
ab fc ge
dh
a2 (Standby-On)
T• urns on this player or switches to
standby mode.
bDisc compartment
cZ(Open/Close)
O• pens or closes the disc compartment.
dIR sensor
Detects signals from the remote• control. Point the remote control at
the IR sensor.
eDisplay panel
fB(Play)
Starts or resumes play.•
gX(Pause)
Pauses play.• Moves the paused picture one step• forward.
h(USB) socket
• Connects a USB supported device.
Downloaded From Disc-Player.com Philips Manuals

12 EN
3 Connect
Make the following connections to use your
Blu-ray disc player.
Basic connections:
Video• Audio• Power•
Optional connections:
Route audio to other devices:• Multi-channel receiver• Digital amplifier/receiver• Analogue stereo system•
USB device• LAN (network)•
Note
Refer to the type plate at the back or bottom of the• product for identification and supply ratings.
Before you make or change any connections, ensure
• that all the devices are disconnected from the power
outlet.
Tip
Different types of connectors may be used to• connect this product to your TV, depending on
availalbility and your needs. A comprehensive
interactive guide to help you connect your product is
availalble at www.connectivityguide.philips.com.
Connect video/audio cables
Connect this Blu-ray disc player to TV to view
disc play. Select the best video connection that
the TV can support.
Option 1:• Connect to the HDMI socket
(for a HDMI, DVI or HDCP-compliant TV).
Option 2:• Connect to the component
video socket (for a standard TV or
Progressive Scan TV).
Option 3:• Connect to the composite video
(for a standard TV).
Option 1: Connect to the HDMI
socket
LAN
HDMI IN
HDMI
DIGITAL AV OUTPUT
1 Connect an HDMI cable to the HDMI
socket on this player and the HDMI input
socket on the TV.
Note
HDMI cable is supplied for BDP7300 only.•
Downloaded From Disc-Player.com Philips Manuals

English
EN 13
Connect
Tip
If the TV has a DVI connector only, connect via an• HDMI/DVI adaptor. Connect an audio cable for
sound output.
You can optimise the video output. Press
• HDMI
repeatedly to select the best resolution the TV can
support.
Use HDMI category 2 cable (High Speed HDMI
• cable) for optimal video and audio output.
To play back the digital video images of a BD-
• Video or DVD-video via an HDMI connection, it is
necessary that both the player and the display device
(or an AV receiver / amplifier) support a copyright
protection system called HDCP (high-bandwidth
digital content protection system).
This type of connection provides best picture quality.
•
Option 2: Connect to the component
video socket
LAN
COMP OUT
Pb
Y
Pr
PbY Pr
AV OUTPUT
AUDIO IN
L
R
L
R
1Connect the component video cables
(not supplied) to the Y PBPRsocket on this
player and the COMPONENT VIDEO
input sockets on the TV.
2 Connect the audio cable to the AUDIO
L/R-AV OUTPUT sockets on this player
and the AUDIO input sockets on the TV.
Tip
The component video input socket on the TV might• be labelled as Y Pb/Cb Pr/Cr or YUV.
This type of connections provide good picture
• quality.
Option 3: Connect to the composite
video socket
LAN
VIDEO
AV OUTPUT
VIDEO IN
AV OUTPUT
AUDIO IN
L
R
L
R
1 Connect a composite video cable to the
VIDEO socket on this player and the
VIDEO input socket on the TV.
2 Connect the audio cable to the AUDIO
L/R-AV OUTPUT sockets on this player
and the AUDIO input sockets on the TV.
Tip
The video input socket on the TV might be labelled• as A/V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connection provides standard picture
• quality.
Downloaded From Disc-Player.com Philips Manuals

14 EN
Route audio to other devices
Route the audio from this Blu-ray disc player to
other devices to enhance audio play.
Connect to multi-channel receiver
(BDP7300 only)
LAN
5. 1ch AUDI O O UT
1 Connect the 5.1-channel audio cables (not
supplied) to the 5.1CH AUDIO OUTPUT
sockets on this player and the
corresponding AUDIO input sockets on
the device.
Tip
You can optimise the speaker output (see ‘Adjust• settings > [Audio Setup] > [Speaker Setup]).
Connect to digital amplifier/receiver
Connect to coaxial socket
LAN
COAXIAL
COAXIAL
1 Connect a coaxial cable (not supplied) to
the COAXIAL socket on this player and
the COAXIAL/DIGITAL input socket on
the device.
Connect to optical socket
(BDP7300 only)
LAN
OPTICAL
OPTICAL
1 Connect an optical cable (not supplied) to
the OPTICAL socket on this player and
the OPTICAL/DIGITAL input socket on
the device.
Downloaded From Disc-Player.com Philips Manuals

English
EN 15
Connect
Connect to analogue stereo system
LAN
AV OUTPUT
AUDIO OUT
1 Connect the audio cable to the AUDIO
L/R-AV OUTPUT sockets on this player
and the AUDIO input sockets on the
device.
Connect USB device
1 Connect the USB device to (USB)
socket on this player.
Note
This player can only play/view MP3, WMA/WMV9,• DivX (Ultra) or JPEG files that are stored on such
devices.
Press
• HOME, select [USB] in the menu to access the
content and play the files
Connect LAN
Connect this player to the network to enjoy
software updates and BD-Live applications.
LAN
LAN
1 Connect the network cable (not supplied)
to the LAN socket on this player and the
LAN socket on the broadband modem or
router.
Note
Internet access to Philips website for software• update may not be allowed, depending on the router
you use or the Internet Service Provider’s policy.
Contact your Internet Service Provider for more
information.
Downloaded From Disc-Player.com Philips Manuals

16 EN
Connect power cord
Warning!
Risk of product damage! Ensure that the power• supply voltage corresponds to the voltage printed on
the back of the underside of this unit.
1 Connect the power cord to the power
outlet when all the required connections
are done.
This player is now ready to be set up
for use.
Downloaded From Disc-Player.com Philips Manuals

English
EN 17
Get started
4 Get started
Insert the remote control
batteries
1 Slide the battery cover off the back of the
remote control.
2 Insert two supplied batteries (AAA). Be
sure the +and -ends of the batteries
line up with the markings inside the case.
3 Slide the cover back into position.
Note
Do not mix batteries (old and new or carbon and• alkaline, etc.).
Remove the batteries If they are exhausted or if the
• remote control is not to be used for a long time.
Batteries contain chemical substances, they should
• be disposed of properly.
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this player and select
the desired function.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V Move up or down.
b B Move left or right.
Confirm a selection.
Enter numbers.
Back to the home menu.
Find the correct viewing
channel
1 Press 2to turn on this Blu-ray disc player.
2 Turn on the TV and switch to the correct
video-in channel in one of the following
ways:
Go to the lowest channel on your TV,• then press the Channel Down button
until you see the PHILIPS screen or the
Home menu.
Press• °SOURCE button repeatedly
on the remote control of your TV.
Tip
The video-in channel is between the lowest and• highest channels and may be called FRONT, A/V IN,
VIDEO, HDMI, etc.. See the TV user manual on how
to select the correct input on the TV.
Downloaded From Disc-Player.com Philips Manuals

18 EN
Use the Home menu
Settings
Play disc USB
Press (Home Menu).
Select• [Play Disc] to start disc play.
Select• [USB] to view the USB contents.
Select• [Settings] to access the setup menus.
Select menu display language
Note
Skips this setting if this player is connected to a• HDMI CEC compliant TV. It switches automatically
to the same OSD menu language as per your TV
setting.
1 In the Home menu, select [Settings] and
press OK.
2 Select [Preference Setup], then press B.
3 Select [OSD Language], then press B.
Parental Control
OSD Language
Screen Saver
Display Panel
Auto Standby
PBC
English
Dansk
Nederlands
Français
Deutsch
Italiano
Norsk
Change PIN
The language options are different• depending on your country or region.
It may not correspond to the illustration
shown here.
4 Press vV to select a language, then press
OK.
Tip
You can set the default language for DVD disc• menu (see ‘Adjust settings’ > [Video Setup] > [Disc
Menu]).
Set up network
Follow the steps below to help you set up the
network connection for software updates and
enjoy BD-Live applications.
LAN
LAN
1 Connect this Blu-ray disc player to the
broadband modem or router. Ensure that
the network cable is properly connected
and the router is switched on.
2 In the Home menu, select [Settings] and
press OK.
3 Select [Advanced Setup], then press B.
4 Select [Network], then press OK.
5 Select [Next] in the menu, then press OK.
The Blu-ray disc player starts to detect
if there is a connection to the network.
If the connection test fails, select•
[Retry] and press OK to re-connect
again to the network.
6. Once connected, an IP address is obtained
automatically.
If no IP address is obtained, select• [Retry] and press OK to try to obtain
the IP address again.
Downloaded From Disc-Player.com Philips Manuals

English
EN 19
Get started
7. Select [Finish] in the menu, then press OK
to exit.
Note
This player does not support automatic detection of• cross-cables.
Loading BD-Live content from the internet may take
• some time, depending on the file size and the speed
of the internet connection.
Use Philips EasyLink
Your Blu-ray disc player supports Philips
EasyLink, which uses the HDMI CEC
(Consumer Electronics Control) protocol.
EasyLink-compliant devices that are connected
through HDMI connectors can be controlled by
a single remote control.
Note
Philips does not guarantee 100% interoperability• with all HDMI CEC compliant devices.
1 Turn on the HDMI CEC operations on the
TV and other connected devices. See TV/
devices manual for details.
2 You can now enjoy the following Philips
EasyLink controls.
EasyLink
Turn off or on all EasyLink features.
One-touch play
When you press PLAY button on the
remote control, the TV (if support
one-touch play) and the Blu-ray disc
player will be turned on. Disc play starts
if there is a disc in the Blu-ray disc player
and the TV automatically switches to the
correct channel to show the video
content.
One-touch standby
When you press and hold STANDBY
button on the remote control, this
player and all the connected HDMI CEC
devices (if support one-touch standby)
switch to standby mode simultaneously.
Downloaded From Disc-Player.com Philips Manuals

20 EN
5 Play
Play a disc
Caution!
Do not place any objects other than discs into the• disc compartment.
Do not touch the disc optical lens inside the disc
• compartment.
1 Press Zto open the disc compartment.
2 Insert a disc with its label facing up.
For double-sided disc, load the side to• play faces up.
3 Press Zto close the disc compartment
and start disc play.
To view disc play, turn on the TV to the• correct viewing channel for this Blu-ray
disc player.
To stop disc play, press• x.
Note
Check the types of discs supported (see• ‘Specifications’ > ‘Playback media’).
If the password entry menu is displayed, enter
• the password before you can play the locked or
restricted disc (see ‘Adjust settings’ > ‘Preference
Setup’ > [Parental Control]).
If you pause or stop a disc, screen saver appears after
• 10 minutes of inactivity. To deactivate the screen
saver, press any buttons.
After you pause or stop a disc and no buttons are• pressed within 30 minutes, this player automatically
switches to standby mode.
Information on disc contents
The contents of disc are generally divided into
sections or folders (groups of titles/files) as
shown below.
BD-video, DVD-video
title 1 title 2
chapter 2
chapter 1 chapter 3
chapter 2
chapter 1
track 2track 1 track 5track 4track 3
Audio CD
MP3, Windows Media™ Audio, JPEG
folder (group) 1 folder (group)
2
file 3file 2
file 1 file 2 file 1
‘Folders’ refers to the groups of files.• ‘Tracks’ refers to the contents recorded on• the audio CD.
‘Files’ refers to the contents on a disc which• are recorded in MP3, Windows Media™
Audio/Video, or JPEG file format.
Downloaded From Disc-Player.com Philips Manuals