Philips DVP620VR/75 Operating manual

There are many ways to connect your new DVD/VCR to your Television and other equipment.This Quick-Use
Guide shows the easiest, most common connection.
Higher quality connections are explained in the accompanying owner’s manual and will provide better sound or
picture if your TV and/or audio system is compatible.
AEREAL
RF OUT
REAR OF TV
(EXAMPLE ONLY)
ANTENNA IN
RF COAXIAL CABLE
IN OUT
CABLE BOX
(Optional)
CABLE TV SIGNAL
ANTENNA or
CABLE TV SIGNAL
1Disconnect all equipment from the power outlets. Connect the equipment to the power outlets only after you
have finished hooking up everything. Never make or change connections with equipment connected to the power outlet.
2Connect your existing RF cable from the Antenna TV signal directly to the AERIAL jack on the rear of the
DVD/VCR. If you have a Cable Box (or Satellite Receiver), connect the OUT jack of the Cable Box/Satellite
Receiver to the AERIAL jack on the DVD/VCR using an RF coaxial cable (not supplied).
3Connect the supplied black RF coaxial cable to the DVD / VCR’s RF-OUT jack and to your TV’s ANTENNA
IN jack. The TV’s ANTENNA IN jack may be labelled 75-ohm,TV IN, or RF IN. Check your TV manual for details.
4Plug the power cords of the DVD/VCR and the TV into an active power outlet.
5Turn on the TV power. Set the TV to a video channel.
6Press the STANDBY-ON 2button on the DVD/VCR or its remote to turn on the DVD/VCR.
The first time you turn on the DVD/VCR, you should complete the VCR setup. See the other side of this
Quick-Use Guide for details.
DVP620VR
-
-
DVP620VR/75 QUG 21/06/2004 03:41 PM Page 1

STANDBY-ON
POWER ON
OPEN/CLOSE
VIDEO REW F.FWD STOP/EJECT PLAY RECORDL --AUDIO -- R STOP PLAYCHANNEL
SOURCE
DVD
VCR
STANDBY-ON AUDIO CLEAR
C.RESET
321
654
987
+109
OK
MENU
MODE
A-B
EJECT
SKIP / CH
SPEED
SLOW
PAU S E
SETUP
MODE
SUBTITLE
TITLE RETURN
ZOOM
ANGLE
SEARCH
SEARCH
REW
SEARCH
FF
REPEAT
TIMER SET
REPEAT
PLAY
STOP
DVD
DISPLAY
STAT U S
OPEN/CLOSE
VCR
RECORD
Quick-Use Guide (cont’d)
Quick-Use Guide (cont’d)
Playing a Disc
1With the TV and DVD /VCR on, press the DVD
button to put the DVD / VCR in the DVD mode.
2Press OPEN/CLOSE /to open the disc tray.
Put a Disc in the tray with the label facing up and the shiny side
facing down.
Press OPEN/CLOSE /again to close the disc tray.
3Playback may start automatically. If not, press PLAY B.
If a DVD Disc menu appears, use the 1,2,3,4or Number
buttons to select features or start playback. Follow the
instructions in the menu.
4To stop playing a Disc, press STOP 9.
Setting Up the VCR the First Time
1Turn on the TV and set it to video channel.
2Press VCR, then press MENU. The VCR light will appear on
the front of the DVD/VCR. The display shown below will
appear.
3Press 3or 4to select “INITIAL”, then press 2.
Press 3or 4to select “CH TUNING”, then press 2.
Press 3or 4to select “AUTO ”, then press 2.
4The AUTO SET UP message will appear. Press 2to set up TV
channels for the VCR. When setup is complete, the lowest TV
channel will appear on the TV.
MENU
2TIMER
SET UP
INITIAL
Playable Discs
The DVD Player of the DVD/VCR will play the following Discs.
DVDs must have a Region Code of ALL regions or Region 4.
DVDs must be recorded in the NTSC or PAL Color System.Your TV
must also have the NTSC or PAL color system
4
ALL
Recordable
ReWritable
Turn on the TV video
channel.
3-4
2
1
2
STANDBY-ON AUDIO CLEAR
C.RESET
321
654
987
+109
OK
MENU
MODE
A-B
EJECT
SKIP / CH
SPEED
SLOW
PAU S E
SETUP
MODE
SUBTITLE
TITLE RETURN
ZOOM
ANGLE
SEARCH
SEARCH
REW
SEARCH
FF
REPEAT
TIMER SET
REPEAT
PLAY
STOP
DVD
DISPLAY
STATUS
OPEN/CLOSE
VCR
RECORD
43
1
Remote Control
Setting
Before using the remote:
• Press ‘DVD’ for DVD
functions.
• Press ‘VCR’ for VCR
functions.
8239 300 34091
1VMN20191/H9723AD*****
DVP620VR/75 QUG 21/06/2004 03:41 PM Page 2