Philips CoolSkin HQ 673/A Assembly instructions

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Rechargeable shaver
HQ 673/A
CoolSkin
4322 277 00485
01/02
TECHNICAL DATA
Input voltage : 100-240 V, 50/60 Hz
Power consumption : max. 9 W
Motor voltage : 1.2 V
Battery : 1x NiCd AA
Battery capacity : approx. 700 mAh
Charging indicator : 1x duoLED green / red
: charge / battery low
Charging time : approx. 8 hours
Charging current : 0.2 C continuous
Charging device : HQ 600 external transformer
Shaving heads : HQ 167 - 4222 036 04250
Shaving emulsion : HQ 160 shaving emulsion
: HQ 161 fresh gel
Mains shaving : no
SAP CODING : HQ 673
TIPS FOR REPAIR
- Remove the shaving unit to prevent damage during repair.
- Remove the slide cover (item 21) and cartridge (item 20).
- Push the edge of the hair chamber up with your thumb
until the snap connection unlocks (see ‘X’ in exploded
view).
- Remove 3 A1 screws.
- Remove the cover (item 14).
- Use a screwdriver to push the connecting plate (item 17)
up at a connecting strip (‘Z’ in exploded view).
- Tilt the motor slightly to detach the snap hooks of the hair
chamber.
- Lift the motor and the PCB out of the housing.
- The cover (item 14) contains a sticker that is permeable to
gas yet impermeable to water.
- This sticker may not be removed under any circumstances.
- The entire drive unit (item 10) is supplied as a single part
to guarantee optimal sealing of the gear shafts.
- When reassembling the shaver, the sealing ring (item 2)
must be placed onto the housing.
- A new sealing ring must be used to ensure a proper
sealing of the shaver.
- To guarantee that the shaver is completely watertight, only
the original screws may be used.
R1
T1
D
D3
R2
R3
D1a D1b
TS1
TS2
D4
Mains
Power plug
Power module
TS4
TS3
C1
L1
L21
R6
IC21
D2a
R4
C3
R5
SK1
C2
R23
C21
R22R21
D2b
D21
C24C23
C22
216 17415 14 10
138201918376
EOO UPC
VCC
EMP
MOO
VAC
VBLI
SMOT
NCEL REFF CTIM TAMB GND TACC VBR
MF2
A
NiCd
AA
D43 PM
C25
R24
TS21
RR
C

1 4822 479 20198 cleaning brush
2 4822 532 13111 sealing ring
3 4222 036 04830 housing PH
4 4222 036 03690 power plug EU
4222 036 03750 power plug GB/SA
5 4222 036 04720 protecting cap
6 4222 036 04840 head housing
7 4222 036 04250 HQ167 shaving head
8 4822 402 11251 retaining bracket
9 4222 036 04730 hairchamber
10 4822 522 10747 gearwheel unit
11 4822 522 10748 pinion
12 4822 361 21752 motor 1.2V
13 4822 492 63165 motor clamp
14 4222 036 04820 cover PH
15 4222 036 04780 release knob
16 4222 036 04810 power module
17 4822 265 11548 connector
18 4222 036 04800 trimmer
19 4822 360 10389 pump
20 4222 036 04400 HQ160 shaving emulsion
4222 036 04410 HQ161 shaving gel
21 4222 036 04770 slide cover
22 4822 130 34167 Zener diode
23 4222 036 01150 motor connector
24 4822 466 12153 foam plate 1 mm
25 4822 466 12155 foam plate 4 mm
26 4822 138 10633 NiCd cell AA
A1 4822 502 14545 s.t.screw spec.
4222 036 04700 case
4222 036 04710 pouch
HQ 673/A
X
A1
NiCd
Z
Y
X
3
2
1
4
24
23
21
22
9
15
17
14
16
10
11
13
12
8
7
6
5
20
19
18
25
26