Philips SP9860 User manual

www.philips.com/support/ifu-lux
BC
Tripleheader shaver
SP9860

4
3
15
14
13
11
10
9
8
7
6
5
1
2
12
16

empty page before TOC

English 6
Español 33

English
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product or charging pad that has
fallen into water. Unplug immediately from the power outlet.
-Keep the power cord and charging pad dry.
-Do not place or store the product or charging pad where it
can fall or be pulled into a tub or sink. Do not place or drop
the product or charging pad into water or other liquid.
-Except when charging, always unplug this product from the
power outlet immediately after use.
-Remove power cord from power outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:
-Close supervision is required when this product is used by,
on, or near children, or persons with limited physical, sensory,
or mental capabilities or invalids.
-Use this product only for its intended household use as
described in this manual. Do not use attachments not
recommended by Philips North America LLC.
6English

-Never operate the product or charging pad if it has a
damaged power cord, if it is not working properly, after it has
been dropped or damaged, or after the product or power
cord has been dropped into water. For assistance call
1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
-Do not charge product or plug in charging pad outdoors or
operate where aerosol (spray) products are being used or
where oxygen is being administered.
-Always check cutters, cutting unit and guards before using
the product. Do not use the product if cutters, cutting unit or
guards are damaged, as injury may occur.
-Always attach power cord to charging pad first, then to
power outlet. To disconnect, set all controls to 'off' position.
Then remove power cord from power outlet.
-Plug power cord directly into power outlet. Do not use an
extension cord.
-Unplug power cord before plugging in or unplugging the
product.
-Only use the power cord and other accessories supplied with
the product.
-Do not attempt to open the product to remove or replace the
built-in rechargeable battery.
-The batteries used in this product may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
-The charging pad is not intended for use in a car. It may
interfere with the automotive electronic systems.
7
English

IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug as this will
cause a hazardous condition.
SAVE THESE
INSTRUCTIONS
Contents
IMPORTANT SAFETY INSTRUCTIONS______________________ 6
General description (Fig. 1)__________________________________ 8
Introduction_________________________________________________ 9
The display__________________________________________________ 9
Charging_____________________________________________________ 13
Using the shaver_____________________________________________ 15
Using click-on attachments_________________________________ 19
Travel lock___________________________________________________ 21
Cleaning and maintenance_________________________________ 22
Replacement________________________________________________ 27
Storage______________________________________________________ 28
Accessories__________________________________________________ 29
Assistance___________________________________________________ 29
Disposal_____________________________________________________ 29
Full Two-Year Warranty_____________________________________ 30
45-DAY MONEY-BACK GUARANTEE_______________________ 31
General description (Fig. 1)
1 Power plug
2 USB plug
3 Wireless Qi charging pad
4 Travel case
5 Notification symbol
8English

6 Cleaning reminder
7 Replacement reminder
8 Travel lock symbol
9 Battery charge indicator
10 Battery charge percentage
11 Personal comfort settings bar
12 + and - buttons for personal comfort
settings
13 On/off button
14 Shaving unit with hair chamber
15 Click-on beard styler attachment
16 Comb for beard styler attachment
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.philips.com/register.
The display
Note: Remove any sticker or protective foil
from the display before using the product.
Charging
When the shaver is charging, the ring on the
pad lights up and the battery charge indicator
on the shaver flashes white.
The battery charge is indicated by the battery
charge percentage flashing on the display,
which is shown when the shaver is moved.
9
English

After approx. 18 minutes charging, the
appliance contains enough energy for one
shave.
Battery fully charged
When the battery is fully charged, the battery
charge indicator and the ring on the pad light
up white continuously.
Note: Both lights switch off automatically after
15 minutes.
The battery charge percentage lights up white
continuously, which is shown when the shaver
is moved.
Battery low
When the battery is almost empty, the battery
charge indicator flashes orange and the shaver
beeps. At this point there is enough energy left
for one shave..
Remaining battery charge
The remaining battery charge is indicated by
the battery charge percentage shown on the
display.
10 English

Personal comfort settings
The shaver has a feature that allows you to
personalize your shave settings. Choose
between three settings, from low to high: slow:
for an even more skin-friendly shave, medium:
for a standard thorough shave, and fast: for a
high-powered shave. When you press the
button on the left or right of the display, the
segment of the personal comfort settings bar
lights up to show the selected setting. To
choose a lower or higher setting, press the
button on the left or right of the display.
Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
When you switch off the shaver, the cleaning
reminder flashes to remind you to clean the
shaver.
Travel lock
3 sec.
When you are going to travel, you can lock the
shaver to prevent it from accidentally
switching on (see 'Activating the travel lock').
Replacement reminder
For maximum shaving performance, replace
the shaving heads every year (see
'Accessories'). The shaver is equipped with a
replacement reminder, which lets you know
when to replace the shaving heads. The shaver
11
English

beeps, the replacement reminder lights up,
and the arrows flash to indicate that you have
to change the shaving heads.
Note: After replacing the shaving heads, you
can reset the replacement reminder by
pressing the on/off button for 7 seconds. If you
do not reset the replacement reminder, the
shaver resets automatically after 9 shaves.
Notification symbol
Overheating
If the shaver overheats during charging, the
notification symbol flashes. When this
happens, the shaver automatically stops
charging. Charging continues once the
temperature of the shaver has decreased to
the normal level after approx. 10 minutes.
Blocked shaving heads
If the shaving heads are blocked, the
notification symbol continuously lights up red.
The replacement reminder and the cleaning
reminder alternately flash white and the
shaver beeps. In this case, the motor cannot
run because the shaving heads are dirty or
damaged. If the shaving heads are dirty, you
have to clean them. If the shaving heads are
damaged, you have to replace them.
12 English

Foreign object on wireless Qi charging pad
If there is a foreign (metal) object on the
wireless Qi charging pad during charging, the
notification symbol on the wireless Qi charging
pad lights up. The wireless Qi charging pad
switches off automatically and restarts 5
minutes after the foreign object has been
removed.
Do not place any foreign (metal) objects on
the wireless Qi charging pad. Only use the
wireless Qi charging pad to charge the shaver
or another device (e.g. smartphone)
compliant with Qi charging.
Charging
-Charging or using the product at
temperatures below 40°F (4.5°C) or higher
than 95°F (35°C) adversely affects the
lifespan of the battery.
-Do not charge the shaver in a pouch or
travel case.
-The power plug transforms 100-240V AC to
less than 24V DC.
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 3 hours. A fully charged
shaver has a shaving timeof up to 60 minutes.
After approx. 18 minutes of charging the shaver
contains enough power for one shave.
13
English

Note: You cannot use the shaver while it is
charging.
Charging with the wireless Qi charging pad
Note: The charging pad is Qi compliant. Only
charge the Qi compatible shaver or other Qi
compliant appliances on the wireless Qi
charging pad provided.
Note: Carefully shake off excess water before
placing the shaver on the Qi pad.
1Put the USB plug in the power plug
supplied.
2
1
2Connect the power plug to any 100V to
240V AC outlet. Use only the power cord
provided.
3Place the shaver on the cross mark of the
wireless Qi charging pad. Make sure the
shaver fits into the cavity of the wireless Qi
charging pad.
Only charge the shaver on the provided
wireless Qi charging pad.
-The wireless Qi charging pad beeps and the
ring on the pad lights up when the shaver is
correctly placed and connected for
charging.
14 English

-When the shaver is charging, the ring on the
pad lights up and the battery charge
indicator on the shaver flashes white. The
battery charge is indicated by the battery
charge percentage flashing on the display,
which is shown when the shaver is moved.
4When the battery is fully charged, the
battery charge indicator and the ring on the
pad light up white continuously. Both lights
switch off automatically after 15 minutes.
Note: An adapter plug may be necessary for
cord usage in some foreign countries. Use an
attachment plug adapter of the proper
configuration for power outlet.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
This symbol indicates that the shaver can be
used in the bath or shower.
-Use this shaver for its intended household
use as described in this manual.
-For hygienic reasons, the shaver should
only be used by one person.
-Trimming is easier when the skin and hair
are dry.
15
English

21-Day adaptation process
-21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
-Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Switching the shaver on and off
1To switch on the shaver, press the on/off
button once.
The battery charge percentage lights up for
a few seconds.
2To switch off the shaver, press the on/off
button once.
The battery charge percentage lights up for
a few seconds and shows the remaining
battery charge.
16 English

Shaving
Shaving tips
-For the best results on skin comfort, pre-
trim your beard if you have not shaved for 3
days or longer.
-Select your personal comfort setting.
Dry shaving
1Switch on the shaver.
2Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
3Switch off and clean the shaver after each
use (see 'Cleaning and maintenance').
The display lights up for a few seconds to
show the remaining battery charge.
Wet shaving
For a more comfortable shave, you can also
use this shaver on a wet face with shaving
foam or shaving gel.
1Apply some water to your skin.
17
English

2Apply shaving foam or shaving gel to your
skin.
3Rinse the shaving unit under the tap to
ensure that the shaving unit glides smoothly
over your skin.
4Switch on the shaver.
5Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
Note: Rinse the shaving unit regularly to
ensure that it continues to glide smoothly
over your skin.
6Dry your face.
7Switch off the shaver and clean it after each
use.
Note: Make sure that you rinse all foam or
shaving gel off the shaver.
18 English

Using click-on attachments
Removing or attaching click-on attachments
1Make sure the shaver is switched off.
2Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off the shaver.
3Insert the lug of the attachment into the slot
in the top of the shaver. Then press down
the attachment to attach it to the
shaver(‘click’).
Using the beard styler attachment with comb
You can use the beard styler attachment with
the comb attached to style your beard at one
fixed setting or at different length settings. You
can also use it to pre-trim any long hairs
before shaving for a more comfortable shave.
The length settings on the beard styler
attachment correspond to the remaining hair
length after cutting and range from 1 to 5mm
(3/64 - 3/16in).
1Attach the beard styler to the product
('click').
19
English

2Slide the comb straight into the guiding
grooves on both sides of the beard styler
attachment (‘click’).
1
2
3Press the length selector and then push it
to the left or right to select the desired hair
length setting.
4Switch on the product.
5Move the product upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
If cut hairs accumulate in the comb, switch
the product off, remove comb and blow
and/or shake hair out of the comb.
6Clean the attachment after use.
Using the beard styler attachment without comb
You can use the beard styler attachment
without the comb to contour your beard,
mustache, sideburns or neckline to a length of
0.5mm (1/32 in).
1Pull the comb off the beard styler
attachment.
Note: Grab the comb in the center to pull it
off the beard styler attachment. Do not pull
at the sides of the comb.
2Switch on the product.
20 English