Philips HQ 8445 User manual

ENGLISH 4
POLSKI 12
ROMÂNĂ 20
РУССКИЙ 28
ČESKY 37
MAGYAR 45
SLOVENSKY 53
УКРАЇНСЬКІЙ 61
HRVATSKI 70
EESTI 78
LATVISKI 86
LIETUVIŠKAI 94
SLOVENŠČINA 102
БЪЛГАРСКИ 110
SRPSKI 119
HQ8445
3

Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗Only use the HQ8000/HQ800 powerplug
supplied.
◗The HQ8000 powerplug transforms 100-240
volts to a safe low voltage of less than 24
volts.
◗The HQ800 powerplug transforms 220-240
volts to a safe low voltage of less than 24
volts.
◗Only use the powerplug that comes with the
appliance to guarantee safe transformation.
◗The powerplug contains a transformer.Do
not cut off the powerplug to replace it with
another plug,as this will cause a hazardous
situation.
C◗Make sure the HQ8000/HQ800 powerplug
does not get wet.
C◗The appliance complies with the
internationally approved IEC safety regulations
and can be safely cleaned under the tap.
Be careful with hot water.Always check if the
water is not too hot,to prevent your hands from
getting burnt.
◗Noise level:Lc= 62 dB [A]
ENGLISH4

Using the appliance
Shaving
Use and store the appliance at a temperature
between 5cC and 35cC.
1Put the powerplug in the wall socket.
C◗The Personal Comfort Control system allows
you to adapt the shaver to your skin type.
- You can set the shaver to 'Normal' for a fast
and comfortable close shave.
- You can set the shaver to 'Sensitive' for a
comfortable close shave with optimal skin
comfort.
C◗The …position is the neutral position.
C◗The 'S' position is best suited for sensitive
skin.
C◗The 'N' position is best suited for normal
skin.
2Switch the shaver on by pressing the on/off
button once.
ENGLISH 5
S
N

C3Move the shaving heads quickly over your
skin,making both straight and circular
movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philishave system.
4Switch the shaver off.
C5Put the protection cap on the shaver every
time you have used it,to prevent damage.
Replace the shaving heads (type HQ8 Sensotec)
every 2 years for optimal shaving results.
Trimming
For grooming sideburns and moustache.
C1Open the trimmer by pushing the slide
upwards.
The trimmer can be activated while the motor is
running.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
The easiest and most hygienic way to clean the
appliance is to rinse the shaving unit and the hair
chamber with hot water (60cC-80cC) every time
you have used the shaver.
When you clean the appliance,it is not necessary
to take the shaving heads (cutters and guards)
ENGLISH6

apart.If you want to take them apart, be sure not
to mix up the cutters and guards,since grinding of
the cutters in the guards only guarantees optimal
performance for each matching set.If you
accidentally mix up the sets,it could take several
weeks before optimal shaving performance is
restored.
Every day:shaving unit and hair chamber
Never dry the shaving unit with a towel or tissue
as this may damage the shaving heads.
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
C2Press the release button to open the
shaving unit.
C3Clean the shaving unit and the hair
chamber by rinsing them under a hot tap
for some time.
Make sure the inside of the shaving unit and the
hair chamber have been cleaned properly.
4Rinse the outside of the appliance.
5Close the shaving unit and shake off excess
water.
C6Open the shaving unit again and leave it
open to let the appliance dry completely.
ENGLISH 7

◗You can also clean the shaving unit and hair
chamber without water by using the brush
supplied.
- Carefully clean the top of the shaving unit with
the brush.
- Carefully clean the inside of the shaving unit
and the hair chamber with the brush.
Every six months:trimmer
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
C2Clean the trimmer with the brush.
C3Lubricate the trimmer teeth with a drop
of sewing machine oil every six months.
Replacement
Replacing the shaving heads
Replace the shaving heads every 2 years for
optimal shaving results.
Replace damaged or worn shaving heads with
HQ8 Philishave Sensotec shaving heads only.
1Switch the shaver off,remove the
powerplug from the wall socket and pull
the appliance plug out of the shaver.
ENGLISH8

C2Press the release button to open the
shaving unit.
C3Turn the wheel anticlockwise and remove
the retaining frame.
C4Remove the shaving heads and place new
ones in the shaving unit in such a way that
the parts with the small holes point
towards the centre of the shaving unit.
Make sure that the projections of the shaving
heads fit exactly into the recesses.
C5Put the retaining frame back into the
shaving unit.Press the wheel and turn it
clockwise.
Storage
C◗Put the protection cap on the shaver to
prevent damage.
◗You can store the appliance in the pouch
supplied.
ENGLISH 9
1
2
2
1

Accessories
The following accessories are available:
- HQ8000 powerplug.
- HQ800 powerplug.
- HQ8 Philishave Sensotec shaving heads.
- HQ110 Philishave shaving head cleaner (shaving
head cleaning spray).
Guarantee & service
If you need information or if you have a problem,
please visit the PhilipsWeb site at
www.philips.com or contact the Philips Customer
Care Centre in your country (you will find its
phone number in the worldwide guarantee
leaflet).If there is no Customer Care Centre in
your country,turn to your local Philips dealer or
contact the Service Department of Philips
Domestic Appliances and Personal Care BV.
Troubleshooting
1Reduced shaving performance
BCause 1:the shaving heads are dirty.
BThe shaver has not been rinsed long enough or
the water used was not hot enough.
◗Clean the shaver thoroughly before you
continue shaving (see 'Cleaning and
maintenance').
BCause 2:long hairs are obstructing the shaving
heads.
ENGLISH10

◗Clean the cutters and guards.
C◗Remove the retaining frame.Do not clean
more than one cutter and guard at a time,
since they are all matching sets.If you
accidentally mix up the cutters and guards,it
may take several weeks before optimal shaving
performance is restored.
◗Remove the hairs with the brush supplied.
◗Put the retaining frame back into the shaving
unit.
BCause 3:the shaving heads are damaged or worn.
◗Remove the retaining frame.
◗Remove the old shaving heads from the
shaving unit and replace them with new ones
Damaged or worn shaving heads (cutters and
guards) may only be replaced with original HQ8
Philishave Sensotec shaving heads.
◗Put the retaining frame back into the shaving
unit.
ENGLISH 11
1
2

Ważne
Przed pierwszym użyciem urządzenia zapoznaj się
dokładnie z instrukcją jego obsługi i zachowaj ją na
przyszłość, do ewentualnej konsultacji
◗Używaj wyłącznie dołączonego do kompletu
zasilacza HQ8000/HQ800.
◗Zasilacz HQ8000 p zekształca napięcie 100-
240 V na bezpieczne niskie napięcie poniżej
24 V.
◗Zasilacz HQ800 p zekształca napięcie 220-
240 V na bezpieczne niskie napięcie poniżej
24 V.
◗Dla zapewnienia bezpieczeństwa używaj
jedynie zasilacza nabytego w az z
u ządzeniem.
◗Integ alnym elementem wtyczki sieciowej jest
t ansfo mato . Odcięcie p zewodu w celu jego
wymiany na nowy spowodować
niebezpieczeństwo.
C◗Upewnij się, czy zasilacz HQ8000/HQ800 nie
jest na ażony na działanie wilgoci.
C◗Niniejsze u ządzenie spełnia międzyna odowe,
zatwie dzone no my bezpieczeństwa IEC i
można je myć pod k anem.
Postępuj ostrożnie z gorącą wodą Zawsze
sprawdzaj, czy jej temperatura jest odpowiednia
dla kontaktu z rękami
◗Poziom hałasu: Lc= 62 dB [A]
POLSKI12