Philips S5588 User manual

www.philips.com/support/ifu
S5588, S5586,
S5581, S5579

3
1
2
4
5
6
7
8 9
11 12
13 14
10
15

empty page before TOC

English 6
Français (Canada) 25

English
6English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome or via the app.
General description
1 Pop-up trimmer
2 Trimmer release slide
3 Shaving unit
4 Shaving unit release button
5 On/off button
6 Handle
7 Socket for small plug
8 Charging stand (specific models only)
9 Supply unit
10 Small plug
11 Protection cap
12 Pouch
13 Quick Clean Pod Cartridge (specific models only)
14 Quick Clean Pod (specific models only)
15 Cleaning brush
Note: The accessories supplied may vary for different
products. The box shows the accessories that have
been supplied with your appliance.
Important safety information
Read this important information carefully before you
use the appliance and its accessories and save it for
future reference. The accessories supplied may vary
for different products.
Danger
- Keep the supply unit dry.

7
English
Warning
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the appliance.
- The supply unit contains a transformer. Do not cut
off the supply unit to replace it with another plug,
as this causes a hazardous situation.
- This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
- Always unplug the appliance before you clean it
under the tap.
- Always check the appliance before you use it. Do
not use the appliance if it is damaged, as this may
cause injury. Always replace a damaged part with
one of the original type.
Philips Quick Clean Pod Cartridge fluid
- Do not swallow.
- Keep out of reach of children.
Caution
- Never immerse the charging stand in water and do
not rinse it under the tap.
- Never use water hotter than 60°C to rinse the
shaver.
- Only use this appliance for its intended purpose as
shown in the user manual.
- For hygienic reasons, the appliance should only be
used by one person.
- Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol
or acetone to clean the appliance.
- If your shaver comes with a cleaning system,
always use the original Philips Quick Clean Pod
cartridge.

8English
- Always place the cleaning system on a stable, level
and horizontal surface to prevent leakage.
- Always make sure the cartridge compartment is
closed before you use the cleaning system.
- When the cleaning system is ready for use, do not
move it to prevent leakage of cleaning fluid.
- Water may drip from the socket at the bottom of
the shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in
a sealed power unit inside the shaver.
- Do not use the supply unit in or near wall sockets
that contain an electric air freshener to prevent
irreparable damage to the supply unit.
- Do not use the cleansing brush on chapped skin,
open wounds, healing wounds, skin recovering
from surgery or if you suffer from a skin disease or
severe skin irritation, such as severe acne, sunburn,
skin infection, skin cancer, inflammation, eczema,
psoriasis, nylon allergy etc.
- Do not use the cleansing brush attachment if you
are taking steroid-based medication, as this may
cause irritation or injury.
- If you wear piercings on your face, remove the
piercings before you use the click-on attachments
or make sure that you do not use the appliance on
or near the piercing.
- If you wear jewelry, contact lenses or glasses,
remove them before you use the click-on
attachments, or make sure that you do not use the
appliance on or near jewelry or glasses.
Battery safety instructions
- Only use thisproduct for its intended purpose and
follow the general and battery safety instructions
as described in this user manual. Any misuse can
cause electric shock, burns, fire and other hazards
or injuries.
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the product.
Do not use an extension cord.
- Charge, use and store the product at a
temperature between 5°C and 35°C.

9
English
- Always unplug the product when it is fully charged.
- Do not burn products and their batteries and do
not expose them to direct sunlight or to high
temperatures (e.g. in hot cars or near hot stoves).
Batteries may explode if overheated.
- If the product becomes abnormally hot, gives off
an abnormal smell, changes color or if charging
takes much longer than usual, stop using and
charging the product and contact your local Philips
dealer.
- Do not place products and their batteries in
microwave ovens or on induction cookers.
- This product contains a rechargeable battery that
is non-replaceable. Do not open the product to
replace the rechargeable battery.
- When you handle batteries, make sure that your
hands, the product and the batteries are dry.
- To prevent batteries from heating up or releasing
toxic or hazardous substances, do not modify,
pierce or damage products and batteries and do
not disassemble, short-circuit, overcharge or
reverse charge batteries.
- To avoid accidental short-circuiting of batteries
after removal, do not let battery terminals come
into contact with metal objects (e.g. coins, hairpins,
rings). Do not wrap batteries in aluminum foil. Tape
battery terminals or put batteries in a plastic bag
before you discard them.
- If batteries are damaged or leaking, avoid contact
with the skin or eyes. If this occurs, immediately
rinse well with water and seek medical care.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.

10 English
General
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the tap.
For safety reasons, the shaver can therefore only
be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a safe
low voltage of less than 24 volts.
What do the icons on my appliance handle mean?
Icon Behavior Meaning
Flashing Clean the appliance under the tap (see
'How do I clean my appliance and the
attachments?').
Flashing
when you
press the
on/off button
The travel lock is activated.
Lights up
when you
pick up the
appliance
The number of bars lit up show the
remaining battery charge.
Bottom light
flashing
orange
The battery is almost empty (see 'How do I
charge my appliance?').
Lights
flashing in
sequence
The appliance is charging.
Lights up
continuously The appliance is fully charged.
Flashing The appliance must be disconnected from
the wall socket before you can switch it on
(see 'How do I charge my appliance?').

11
English
What does the icon on my Quick Clean Pod mean?
Icon Behavior Meaning
Becomes visible on the
Quick Clean Pod The Quick Clean Pod Cartridge needs to be replaced.
How do I charge my appliance?
Charge the appliance before you use it for the first
time and when the bottom light of the battery status
indicator flashes orange, indicating that the battery is
almost empty.
Charging takes approx. 1 hour.
Quick Charge: After approx. 5 minutes of charging, the
battery contains enough energy for one full shave.
When the appliance is fully charged it has a cordless
operating time of up to 60 minutes.
Note: You cannot use the appliance while it is
charging.
Charging with the supply unit
1Make sure that the appliance is switched off.
2Insert the small plug into the appliance and put the
supply unit in the wall socket.
- While the appliance is in quick charge mode,
the lights of the battery status indicator light up
one after the other. After approximately 5
minutes, the bottom light of the battery status
indicator flashes. The battery now contains
enough energy for one full shave.
- While the appliance charges, first the bottom
light of the battery status indicator flashes and
then lights up continuously. Next the second
light flashes and then lights up continuously,
and so on until the appliance is fully charged.
- When the appliance is fully charged, all three
battery indicator lights light up continuously.
After approx. 30 minutes, the light goes out
automatically.

12 English
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Charging in the charging stand (specific models only)
1Make sure the appliance is switched off.
2Put the small plug in the charging stand and put
the supply unit in the wall socket.
3Place the appliance in the charging stand.
Specific models only: The light ring on the bottom
of the charging stand lights up and rotates quickly.
- After approximately 5 minutes, the light ring
rotates slower. The battery now contains
enough energy for one full shave.
- As the appliance continues to charge, the light
ring becomes brighter and rotates slower.
- When the appliance is fully charged, the light
ring lights up fully and stops rotating.
4After charging, remove the supply unit from the
wall socket and pull the small plug out of the
charging stand.
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind you to
disconnect the appliance from the wall socket and
remove the small plug from the appliance before you
switch it on.
How do I use my appliance and the attachments?
Warning: Always check the appliance and all
accessories before use. Do not use the appliance
or any accessory if it is damaged, as this may
cause injury. Always replace a damaged part with
one of the original type.
Note: This appliance is waterproof. It is suitable for use
in the bath or shower and for cleaning under the tap.

13
English
For safety reasons, the appliance can therefore only
be used without cord.
Shaving
You can use this appliance either wet or dry, or even
under the shower. For a wet shave, apply some water
and shaving foam or gel to your skin and rinse the
shaving heads under the tap with warm water before
following the steps below.
1Switch on the appliance.
2Move the shaving heads over your skin in circular
movements to catch all hairs growing in different
directions. Make sure each shaving head is fully in
contact with the skin. Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, as this can cause skin
irritation.
Note: If you are shaving with gel or foam, rinse the
shaving unit regularly during your shave to ensure
that it continues to glide smoothly over your skin.
3Use the narrow sides of the shaving unit to shave
in hard-to-reach areas such as along your jawline
and under your nose.
4Switch off and clean the appliance after each use.
Note: Make sure you rinse all foam or shaving gel
off the appliance.
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need time

14 English
to adapt to any new shaving system. To allow your
skin to adapt to this new appliance, we advise you to
shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3 weeks.
Cleaning reminder
When you switch off the appliance, the cleaning
reminder flashes to remind you to clean the appliance.
- Clean the appliance and attachments after each
use to prevent clogging and damage (see 'How do I
clean my appliance and the attachments?').
- Clean the shaving heads thoroughly once a month
or when the appliance does not shave as well as it
used to (see 'Thorough cleaning').
Trimming
You can use the trimmer to groom your sideburns and
moustache.
1Push the trimmer release slide downwards to open
the trimmer.
2Switch on the appliance.
3Hold the trimmer perpendicular to the skin and
move the appliance downwards while you exert
gentle pressure.
4You can also use the trimmer under your nose.
5Switch off the appliance and clean the trimmer
after each use to prevent clogging and damage
(see 'How do I clean my appliance and the
attachments?').
6Close the trimmer.
How do I clean my appliance and the attachments?
Clean the appliance and the attachments after each
use for optimal performance.

15
English
Cleaning the shaver under the tap
Clean the shaver after each use to prevent clogging
and damage.
Never dry the shaving unit with a towel or tissue, as
this may damage the shaving heads.
While rinsing the shaving unit, water may drip out of
the base of the shaver. This is a normal occurrence.
1Switch on the shaver.
2Rinse the shaving unit under a warm tap.
3Switch off the shaver. Press the release button to
open the shaving unit.
4Rinse the hair chamber under a warm tap.
5Rinse the shaving head holder under a warm tap.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.
7Close the shaving unit.

16 English
Thorough cleaning
We advise you to clean the shaving heads thoroughly
once a month or when the shaver does not shave as
well as it used to.
1Make sure that the appliance is switched off and
disconnected from the wall socket.
2Press the release button on the shaving unit and
pull the shaving head holder off the shaving unit.
3Rinse the hair chamber and shaving head holder
under the tap.
4Remove the shaving heads. For detailed
instructions, see 'How do I replace the shaving
heads?.'
Note: Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally put a cutter in the wrong shaving
guard, it may take several weeks before optimal
shaving performance is restored.
5Clean the cutter and guard under the tap.
6Shake off excess water.
7Put the shaving heads back into the shaving unit.
For detailed instructions, see 'How do I replace the
shaving heads?.'
8Insert the hinge of the shaving head holder into the
slot in the top of the shaving unit and close the
shaving unit.
Cleaning the pop-up trimmer
Clean the trimmer after each use to prevent clogging
and damage.

17
English
Never dry the trimmer teeth with a towel or tissue, as
this may damage the trimmer teeth.
1Make sure that the appliance is switched off and
disconnected from the wall socket.
2Push the trimmer release slide down to open the
pop-up trimmer.
3Switch on the appliance and rinse the pop-up
trimmer with warm water.
4After cleaning, switch off the appliance.
5Carefully shake off excess water and let the pop-
up trimmer air dry.
6Close the trimmer.
Tip: For optimal performance, lubricate the teeth of
the pop-up trimmer with a drop of mineral oil every
six months (oil not included).
How do I use the Quick Clean Pod? (specific models
only)
Preparing the Quick Clean Pod for use
1Twist and remove the top of the Quick Clean Pod.
2
1
2Twist the lid off of the Quick Clean Pod Cartridge.

18 English
3Lift the tab on the seal and pull it by the corner to
remove the seal from the Quick Clean Pod
Cartridge.
4Press the small circular piece on the handle of the
Quick Clean Pod Cartridge to break the snap hook
on the handle.
5Place the Quick Clean Pod Cartridge into the Quick
Clean Pod.
6Put the top of the Quick Clean Pod back onto the
base and turn it clockwise until you hear a click.
Do not tilt the Quick Clean Pod to prevent leakage.
Using the Quick Clean Pod (specific models only)
Note: If you use the shaver with shaving foam, shaving
gel or pre-shave products, thoroughly rinse the
shaving heads before you use the Quick Clean Pod
(see 'How do I clean my appliance and the
attachments?').

19
English
Always shake excess water off the shaver before you
place it in the Quick Clean Pod.
1Place the shaver upside down into the Quick Clean
Pod. The shaver automatically detects that it is in
the Quick Clean Pod.
2Switch on the shaver to start the cleaning program.
Each cleaning program takes approximately one
minute. During the cleaning program the cleaning
symbol lights up continuously and the blue icon
pulses.
The shaver handle vibrates twice quickly when the
cleaning program is finished.
3Let the shaver air-dry completely in the Quick
Clean Pod before storing it.
Replacing the Quick Clean Pod Cartridge (specific models
only)
Replace the Quick Clean Pod Cartridge immediately
when the cartridge replacement icon on the Quick
Clean Pod becomes visible or follow the table below.
Frequency of use Cycles When to replace the
Quick Clean Pod
Cartridge
Every day About 30 Every month
A few times per week About 20 Every 2 months
Every week About 13 Every 3 months
Every month About 3 Every 3 months
1Twist and remove the top of the Quick Clean Pod.

20 English
2Lift the Quick Clean Pod Cartridge out of the Quick
Clean Pod by the handle.
3Pour any remaining fluid down a drain and recycle
the empty cartridge in accordance with local waste
regulations.
4Place a new Quick Clean Pod Cartridge into the
Quick Clean Pod (see 'Preparing the Quick Clean
Pod for use').
Scan the QR code to the left or visit
www.philips.com/cleaning-cartridge to order
replacement Quick Clean Pod Cartridges.
How do I replace the shaving heads?
For maximum shaving performance, we advise you to
replace the shaving heads every two years.
Replace damaged shaving heads immediately. Always
replace the shaving heads with original Philips shaving
heads (see 'Ordering accessories').
Replacing the shaving heads
1Switch off the shaver.
2Press the release button on the shaving unit and
pull the shaving head holder off the shaving unit.