Philips NOLELCO 5000 Series User manual

BC
Tripleheader shaver
S5000

3
1
2
4
5
6
7
8 9
10
11

English 6
Español 26

English
Contents
IMPORTANT SAFETY INSTRUCTIONS______________________ 6
General description_________________________________________ 9
Introduction_________________________________________________ 10
What do the icons on my product handle mean?__________ 10
How do I charge my product?_______________________________ 11
How do I use my product?__________________________________ 12
How do I clean my shaver?_________________________________ 17
How do I replace the shaving heads?______________________ 20
Accessories__________________________________________________ 22
Assistance___________________________________________________ 22
Disposal_____________________________________________________ 23
Full Two-Year Warranty_____________________________________ 23
45-DAY MONEY-BACK GUARANTEE_______________________ 24
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product that has fallen into water.
Unplug immediately from the power outlet.
-Keep the power cord dry.
6English

-Do not place or store the product where it can fall or be
pulled into a tub or sink. Do not place or drop the product
into water or other liquid.
-This product does not work while it is connected to the
power outlet. Except when charging, always unplug this
product from the power outlet.
-Remove power cord from power outlet and product before
cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:
-Close supervision is required when this product is used by,
on, or near children, or persons with limited physical, sensory,
or mental capabilities or invalids.
-Use this product only for its intended household use as
described in this manual. Do not use attachments not
recommended by Philips North America LLC.
-Never operate this product if it has a damaged power cord, if
it is not working properly, after it has been dropped or
damaged, or after the product or power cord has been
dropped into water. For assistance call 1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
7
English

- Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
- Do not use product outdoors or operate where aerosol
(spray) products are being used or where oxygen is being
administered.
-Always check shaving heads (caps and cutters) before using
the product. Do not use the product if cutters or caps are
damaged, as injury may occur.
- Always attach power cord to product first, then to power
outlet.
- Plug power cord directly into power outlet. Do not use an
extension cord.
- Unplug power cord before plugging in or unplugging the
product.
- Only use the power cord (HQ8505) and other accessories
supplied with the product.
- Do not attempt to open the product to remove or replace the
built-in rechargeable battery.
- The batteries used in this product may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug as this will
cause a hazardous condition.
Battery safety instructions
-Charge, use and store the product at a temperature between
5°C and 35°C.
-Do not burn products and their batteries and do not expose
them to direct sunlight or to high temperatures (e.g. in hot
cars or near hot stoves). Batteries may explode if overheated.
8English

-If the product becomes abnormally hot, gives off an
abnormal smell, changes color or if charging takes much
longer than usual, stop using and charging the product and
contact your local Philips dealer.
-Do not place products and their batteries in microwave
ovens or on induction cookers.
-When you handle batteries, make sure that your hands, the
product and the batteries are dry.
-To prevent batteries from heating up or releasing toxic or
hazardous substances, do not modify, pierce or damage
products and batteries and do not disassemble, short-circuit,
overcharge or reverse charge batteries.
-To avoid accidental short-circuiting of batteries after
removal, do not let battery terminals come into contact with
metal object (e.g. coins, hairpins, rings). Do not wrap batteries
in aluminum foil. Tape battery terminals or put batteries in a
plastic bag before you discard them.
-If batteries are damaged or leaking, avoid contact with the
skin or eye. If this occurs, immediately rinse well with water
and seek medical care.
SAVE THESE
INSTRUCTIONS
General description
1 Pop-up trimmer
2 Trimmer release slide
3 Shaving unit
4 Shaving unit release button
5 On/off button
6 Handle
7 Socket for small plug
9
English

8 Power plug
9 Small plug
10 Protection cap
11 Cleaning brush
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benefit from the
support that Philips offers, register your
product at www.philips.com/welcome or via
the app.
What do the icons on my product handle
mean?
Icon Behavior Meaning
Flashing when
you switch off
the product
Clean the shaver with warm water.
Flashing when
you press the
on/off button
The travel lock is activated (see
'Storage and travel').
Lights up when
you pick up the
product
The number of bars lit up show the
remaining battery charge.
Bottom light
flashing orange
The battery is almost empty (see 'How
do I charge my product?').
Lights flashing in
sequence
The product is charging.
Lights up
continuously
The product is fully charged.
10 English

Icon Behavior Meaning
Flashing The product must be disconnected
from the power outlet before you can
switch it on (see ''Unplug for use'
symbol ').
How do I charge my product?
Charge the product before you use it for the
first time and when the bottom light of the
battery status indicator flashes orange,
indicating that the battery is almost empty.
Charging takes approx. 1 hour.
Quick Charge: After approx. 5 minutes of
charging, the battery contains enough energy
for one shave.
When the product is fully charged it has a
cordless operating time of up to 60 minutes.
Note: You cannot use the product while it is
charging.
Charging with the power cord
1Make sure that the product is switched off.
2Insert the small plug into the product and
put the power plug in the wall outlet.
-While the product is in quick charge
mode, the lights of the battery status
indicator light up one after the other.
After approximately 5 minutes, the
bottom light of the battery status
indicator flashes. The battery now
contains enough energy for one shave.
11
English

-While the product charges, first the
bottom light of the battery status
indicator flashes and then lights up
continuously. Next the second light
flashes and then lights up continuously,
and so on until the product is fully
charged.
-When the product is fully charged, all
three battery status indicator lights light
up continuously. After approx. 30
minutes, the light goes out automatically.
3After charging, remove the power plug from
the power outlet and pull the small plug out
of the product.
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind
you to disconnect the power cord from the
power outlet and remove the small plug from
the product before you switch it on.
How do I use my product?
Always check the product and all
accessories before using. Do not use the
product or any accessory if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
Note: This product is waterproof. It is suitable
for use in the bath or shower and for cleaning
12 English

under the tap with water. For safety reasons,
this product can only be used without cord.
Use this product for its intended household
use as described in this manual.
For hygienic reasons, the product should only
be used by one person.
Shaving
You can use this product either wet or dry, or
even in the shower. For a wet shave, apply
some water and shaving foam or gel to your
skin and rinse the shaving heads under the tap
with warm water before following the steps
below.
1Switch on the product.
2Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
Note: If you are shaving with gel or foam,
rinse the shaving unit regularly during your
shave to ensure that it continues to glide
smoothly over your skin.
13
English

3Use the narrow sides of the shaving unit to
shave in hard-to-reach areas such as along
your jawline and under your nose.
4Switch off and clean the product after each
use.
Note: Make sure you rinse all foam or
shaving gel off the product.
21-Day adaptation process
-21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
-Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
14 English

-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Cleaning reminder
When you switch off the product, the cleaning
reminder flashes to remind you to clean the
product.
-Clean the product and attachments after
each use (see 'How do I clean my shaver?')
to prevent clogging and damage.
-Clean the shaving heads thoroughly once a
month or when the product does not shave
as well as it used to.
Trimming
You can use the pop-up trimmer to groom
your sideburns and moustache.
1Push the trimmer release slide downwards
to open the trimmer.
2Switch on the product.
3Hold the trimmer perpendicular to the skin
and move it downwards while exerting
gentle pressure.
15
English

4You can also use the trimmer under your
nose.
5Switch off the product and clean the
trimmer after each use to prevent clogging
and damage (see 'How do I clean my
shaver?').
6Close the trimmer.
Storage and travel
-Be sure the product is switched off. Remove
the power cord from power outlet and the
product before storing it in a safe, dry
location where it will not be crushed,
banged, or subject to damage.
-Do not wrap cord around the product when
storing.
-Store cord and other accessories in a safe
location where these will not be cut or
damaged.
-Do not place or store the product where it
can fall or be pulled into a tub or sink, water
or other liquid while plugged in.
Note: We advise you to let the product and its
attachments dry completely before you store
them for the next use.
-Put the protection cap on the shaver to
protect it.
Travel lock
You can lock the shaver when you are going to
travel to prevent it from switching on
accidentally.
16 English

Activating the travel lock
3 sec.
Press the on/off button for 3 seconds to use
the travel lock mode.
When the travel lock is activated, the travel
lock symbol flashes.
Note: Bluetooth is switched off when the travel
lock is activated.
Deactivating the travel lock
Press the on/off button for 3 seconds.
Once the travel lock is deactivated, the
product switches on automatically.
Note: The product unlocks automatically when
connected to a power outlet.
How do I clean my shaver?
Clean the product and the attachments after
each use for optimal performance.
Cleaning the shaver with water
Clean the shaver after each use to prevent
clogging and damage.
Never dry the shaving unit with a towel or
tissue, as this may damage the shaving
heads.
While rinsing the shaving unit, water may drip
out of the base of the shaver. This is a normal
occurrence.
17
English

1Switch on the shaver.
2Rinse the shaving unit with warm water.
3Switch off the shaver. Press the release
button to open the shaving unit.
4Rinse the hair chamber with warm water.
5Rinse the shaving head holder warm water.
6Carefully shake off excess water and let the
shaving head holder air-dry completely.
7Close the shaving unit.
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver
does not shave as well as it used to.
18 English

1Make sure that the appliance is switched off
and disconnected from the wall socket.
2Press the release buttons on the shaving
unit and pull the shaving head holder off
the shaving unit.
3Rinse the hair chamber and shaving head
holder with warm water.
4Remove the shaving heads. For detailed
instructions, see 'How do I replace the
shaving heads?.'
Note: Do not clean more than one cutter
and guard at a time, since they are all
matching sets. If you accidentally put a
cutter in the wrong shaving guard, it may
take several weeks before optimal shaving
performance is restored.
5Clean the cutter and guard with warm
water.
6Shake off excess water.
7Put the shaving heads back into the shaving
unit. For detailed instructions, see 'How do I
replace the shaving heads?.'
8Insert the hinge of the shaving head holder
into the slot in the top of the shaving unit
and close the shaving unit.
19
English

Cleaning the pop-up trimmer
Clean the trimmer after each use to prevent
clogging and damage.
Never dry the trimmer teeth with a towel or
tissue, as this may damage the trimmer teeth.
1Make sure that the appliance is switched off
and disconnected from the wall socket.
2Push the trimmer release slide down to
open the pop-up trimmer.
3Switch on the appliance and rinse the pop-
up trimmer with warm water.
4After cleaning, switch off the appliance.
5Carefully shake off excess water and let the
pop-up trimmer air dry.
6Close the trimmer.
Tip: For optimal performance, lubricate the
teeth of the pop-up trimmer with a drop of
mineral oil every six months (oil not included).
How do I replace the shaving heads?
For maximum shaving performance, replace
the shaving heads once a year. Replace
damaged shaving heads immediately.
Always replace the shaving heads with original
Philips Norelco shaving heads (see
'Accessories').
20 English

Replacing the shaving heads
1Switch off the shaver.
2Press the release buttons on the shaving
unit and pull the shaving head holder off
the shaving unit.
12
3Turn the retaining rings counterclockwise
and remove them. Place them aside in a
safe place.
4Remove the shaving heads from the
shaving head holder.
Discard the used shaving heads
immediately to avoid mixing them with the
new shaving heads.
5Place new shaving heads in the holder.
1
2
6Place the retaining rings back onto the
shaving heads and turn them clockwise to
reattach the retaining ring.
21
English

-Each retaining ring has two recesses that fit
exactly into the projections of the shaving
head holder. Turn the ring clockwise until
your hear a click to indicate that the ring is
fixed.
Note: Hold the shaving head holder in your
hand when you reinsert the shaving heads
and reattach the retaining rings. Do not
place the shaving head holder on a surface,
as this may cause damage to the shaving
heads.
7Insert the hinge of the shaving head holder
into the slot in the top of the shaving unit
and close the shaving unit.
Accessories
Replacement parts and accessories may be
purchased at a store near you or on our
website www.philips.com/store.
The following accessories and spare parts are
available:
-SH71 Philips Norelco replacement shaving
heads
Assistance
For assistance, visit our website:
www.philips.com/support or call toll free
1-800-243-3050.
22 English