Philips Norelco G390 User manual

PHILIPS
$ NORELCO
ALL IN 7
GROOMING
SYSTEM
G390. G3SQ. G37G
Rechargeable
Cordless
Rosier pour product and get support at
www.phillps.com/n o relco

ENGLISH
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
the following;
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
L Do not reach for a Groomer/chaiging stand
that has fallen into water. Unplug immediately.
2. Do not use while bathing or in a shower,
3. Do not place or store Groomer/charg^ng
stand where it can fall or bo pulled into a tub
or sink. Do not place in or drop into water
or other liquid.
4. Always unplug this Groomer/charging stand
from the electrical outlet immediately after
using, except when Groomer is (re)charging.
5. Unplug Groomer/charging stand before
cleaning.
6. When discarding Groomer, unplug
Groomer to remove rechargeable battery.
See Battery Removal Instructions.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1, Close supervision is necessary when
this appliance Is used by. on, or near children
or Invalids.
2, Use this Groomer for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3, Never operate this Groomer if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or
dropped into water, For assistance call
1-306-243-3050.
4, Keep the GroOmer/charging stand, card and
any attachments away from heated surfaces.
5, Never drop or insert any object into any
opening.
6, Do not operate, charge or plug in Groomer/
charging stand outdoors or where aerosol
(spray) products are being used or where
oxygen is being administered.
7, Always check foil, cutters, cutting unit and
trimmers before using the Groomer. Do
not use the groomer if foil, cutters, cutting
unit or trimmers are damaged, as injury may
occur.
3. Always attach plug to Groomcr/charging
stand first, then to outlet.To disconnect, turn
on/off switch to “OFF" position, then remove
plug from outlet.
9. To prevent possible damage to the cord, do
not wrap cord around the Groomer.
10. Never put Groomer in direct sunlight or
store at a temperature above 140 R
I I. This Groomer is for use on human hair only.
Do not use this groomer for any other
purpose.
12, Always store your Groomer/charging stand,
attachments and power plug in a moisture-
free area. Make sure the cord is disconnected
from the Groomer.

SAVE THESE
INSTRUCTIONS
IMPORTANT: YOUR GROOMER
CONTAINS A NICKEL-CADMIUM
RECHARGEABLE BATTERY.
See Battery Removal Instructions,
IM PORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
Put It To The Test
bke many new products, your Philips Noreloo
All in 1 Grooming System may take a little getting
used to, if you arc using an electric Groomer for the
first time, or if you've been using a different brand,
take the time to acquaint yourself wsth your new
Grooming System.
Your AH In I Grooming System features the unique
AccuControl System combined with adjustable
Length Settings to make trimming facial hairs or hair
dipping goof proof.
Throw your scissors away and put your new All
in i Grooming System to the test. We guarantee
precise, professional results or Philips Norelco will
refund you the full purchase price as long as the
request is received within 45 days of purchase.
Registration
Congratulations on your purchase and welcome
to Philips Norolcot
To fully benefit from the support chat Philips
Norelco offers, register your product at
www, phi I i ps .com/n ore Ico

Features
A Precisio n Trimmer Attachment
B Full Width Trimmer Attachment
C Lifetime Self-Sharpening 3-Dimensional
Rounded Stainless Steel Cutter Blades
D Accu Control Beard & Moustache Trimmer
Guide Comb
E Hair Clipping Comb
F 9 Position Hair Length Selector
G Release Button
H On/Off Slide Switch
I Socket for appliance plug
J Cleaning Brush
K Styling Comb
L LED Charging Indicator Light on Adaptor
M Appliance Plug
N Charging Plug
O Nose, Far. Eyebrow Trimmer Attachment
P Mini Shaver
Q Store A Charge Stand
R R i nsable Attachme nts
Pouch (models G390 and G380 only)
Full Two-Year Warranty
45-Day Money-Back Guarantee

To Charge/Recharge
I Fully charge Groomer before using for the first
time or after non-use fora long period of time.
> Battery performance is best if you recharge
oniy when the battery Is (almost} completely
empty.
> Charging or recharging at temperatures below
40'F or higher than 95’F adversely affects
lifespan of the battery,
t Continuously recharging Groomer will reduce
lifespan of battery.
If Be certain Groomer is OFF.
B You may charge the Groomer:
I In tine charging stand by inserting the appliance
plug into the socket located In the bottom of
the charging stand (fig. 2). Place the Groomer
direedy on the charging pin in the stand (fig. 3).
I By inserdng the appliance pJug directly into the
Groomer (fig. 4).
O p lug charging plug into any 120VAC outlet.
Use only the cord provided.
□ After a few moments, the Charging Indicator
Light on. the power plug will light to indicate
the Groomer is charging (fig. 5).
> It will take approximately 10 hours to fully
charge the Groomer for a cordless trimming
time of up to 35 minutes.
> Disconnect the cord and unplug from
electrical outlet,
Optimize the working life of the battery
I After the Groomer has been charged for
the first time, do not recharge the Groomer
between trimming sessions, Continue using it
until the batcery is completely empty.
I Do not charge for more chan 24 hours.
I Do not keep cord permanently plugged in.
> Discharge/run down the batce ry completely
twice a year by letting the motor run until it
stops.
> If the Groomer hasn't been used for a long
period of time. It must be recharged for a
full 10 hours.
Cordless Trim m mg
Q Charge according to directions. Unplug
Groomer from outlet.
B Slide ONfOFF switch ON to begin trimming,
□ If the battery is empty and you want to trim
your beard, charge the Groomer for at least
3 hours and you will have enough power for
one use (10 minutes}.

AccuControl System
The unique Philips Nonelco AccuControl System
puls you in complete control while trimming your
facial hairs v^ith no prior experience needed r he
flexing Guide Comb adjusts automatically to hug
the contours of your face for a tnm that is both
even and accurate. And. it's easy to maneuver
over those hard-to-reach areas such as the throat
and chin.The Hair Length Selector allows you to
choose among 9 preset hair lengths and clicks into
position so you can control the exact hair length
you desire or vary the length of your facial hair
The Hasr Clipping Comb also Features 9 preset
hair lengths and dicks into position so you can
control the exact hair length you desire. The
Philips Nor'clco AH in I Grooming System for
professional, goof-proof results every time.
Trimming
It Make sure hair is dean and dry.
I Always comb the hair with the styling comb
in the direction of growth before you start
trimming.
Do not move the Groomer too fast. Make smooth
and gentle r nQyemgnjS. .
Trimming your Beard Sr Noustache
with AccuControl Guide Comb
Attachment
I Use this Groomer for its intended household
use as described in this manual.
I Make sure that the Groomer is fully charged
before you start trimming. This Groomer will
not operate while cord is connected to
electrical outlet.
D Put the AccuControl comb on the full width
trimmer attachment until you hear it click
into place (fig. 6).The AccuControl Comb
will not work with the smaller neckline
and sideburn trimmer, or mini shaver
attachments,
0 Press the Hair Length Selector and slide
it to the desired trimming length setting,
The selected setting number will appear in
the window to the left of the Hair Length
Selector (fig. 7 ). See Table I for settings,

• If you arc trimming for the first Eirnc, start by
using the AccuControl comb at the maximum
trimming length setting (#9) to prevent
accidentally trimming hairs too short.As you
become familiar with the settings, adjust Hair
Length Selector to desired trimming length.
Selector will "click" Into position at each
setting.
H Switch the Groomer ON.
□ To trim in the most effective way. move
the Groomer against the direction of hair
growth. Make sure the surface of the Guide
Comb always stays m contact with the skin
tngs).
NO i F~ Since all hairs do not grow m the same
dirertian. you.may want to. try different trimming
directions.. Lie.. .uP.wW^d.o.w.nLWdrci5, .pr-dCgasd..
Practice is best for optimum results.
I If a fot of hair has accumulated in the Guide
Comb, remove the comb and blow and/or
shake the hair out of the comb.You can also
use the cleaning brush provided to remove
hair from the comb area.
I REMEMBER:You must reset the hair length
selector back to your desired setting every
time you replace the guide edmb on the
appliance.
Table 1, Beard Trimmer
Setting Remaining li.iir length
(in.) .'(mm)
I StiAOIe
.00 in/imm
2
Gt{3£«!
1 6 ittZ+n mi
3
Short
4 Medium Short .3i >rUfSmm
5
Med rum
39 in/IOrtrn
6
Medium long
1 Long in/ [ irm
H
Extra Long
63 in/ 16mm
9 Longest
71 Irt/I0rrtr*
I The remaining hair length corresponds wiEh
the smallest distance between the cutting blade
and the spot where the comb is in contact
with the skin.
I Cutting without the comb attachment or
setting the AccuControE guide comb to # I
position, will result in a stubble beard look.

Beard Trimming Without
AceuControi Comb
Remove comb if you are:
& Defining hair lines
I Trimming nape of neck
► Removing single, unwanted hairs
H Be certain the Groomer is in the OFF
position.
Q Remove the AceuControi comb attachment
by pressing and sliding the Hair Length
Selector upwards (fig. ?).
Never pull off ihe AceuControi comb attachment
by grasping the flexible top portion. Always pull off
by the bottom part of attachment
Q Switch the Groomer ON.
Q Make welF-con trolled movements.Touch the
hairyskin lightly with the Groomer.
Defining Beard, Moustache arid
Sideburns
Q Be certain the Groomer is in the OFF
position,
Q Remove the AceuControi comb attachment
by pressing and sliding the Hair Length
Selector upwards (fig.'?),
Q Detach the full width trimmer attachment by
pushing the release button (fig. 10).
Q Put the precision trimmer attachment on the
Groomer (fig, I I). You will hear a dick,
t Hold the Groomer upright when you use the
precision trimmer attachment (fig. I2) r
Using Nose* Ear & Eyebrow
Trimmer Attachment
n &e certain the Groomer is in the OFF
position,
Q Toattach or remove nose, ear, eyebrow
trimmer (or change attachments):
► Remove the AceuControi comb attachment
(fig. 9).
I Remove the full width trimmer attachment by
pushing the release button (.fig. (0),
> Put the nose, ear, eyebrow attachment on the
Groomer [fig. 13). You will hear a dick.

Trimming Nose Hair
> Mike sure nasal passages are dean.
u Place nose, ear and eyebrow attachment on
Groomer.
19 Switch the Groomer on and insert the tip of
the attachment into one nostril (fig,, 14),
CA UTIO N: D o N o t ins ert the tip more
than 3/1 6 mJ 5 mmj nto you r. nostri L
Q Slowly move the tip in and out while
turning it around at the same time in order
to remove unwanted hair, For best results,
make sure the side of the tip is firm against
skin. This will reduce the tickling effect that
can occur during trimming of nose halr.
□ Turn off Groomer. Rinse attachment clean
after each use.
Trimming Ear Hair
> Clean outer area of ear and ear canal. Make
sure it is free of wax,
>• Nose, ear and eyebrow attachment should be
on the Groomer
i9 Switch the Groomer on and move the tip
softly Jiround the edge of ear to remove hairs
extending beyond the outer ear (fig. IS).
H Carefully insert the tip into outer ear canal.
C AUTl QN: Do not insert the dp further
than 3)16 in./5mm into the ear as this
could caus e d amage to_the eardrum
m.m
Q Turn off Groomer. Rinse attachment dean
after each use.
Trimming Eyebrow
I Nose, ear and eyebrow attachment shouEd be
on Groomer,
H Switch the Groomer on and use the Up to
cut individual eyebrow hairs.
The Groomer can be used for clipping single long
hairs,
H Put the Groomer at the root of the hair and
move it along the edge of the eyebrow from
the base of the nose towards the outer tip of
the eyebrow In the direction of hair growth
(fig. 17).
IMPORTANT: Do not use the Groomer to define
o: trim the r ■ lire r-yfhi'ow. Do no : : w .. _
your eyelashes. Be careful not to get too dose fo
your eyelashes and e;.e>
0Tu rn off Groomer Rinse attachment dean
after each use.

Shaving With Mini Shaver
Attachment
Ml Put the mini shaver attachment on the
Groomer (fig, [13).
H Use the narrow mint shaver to shave
along contoured edges to remove any
stubbie while creating a smooth, well-
defined beard line.
Before using the mini shaven always check n for
wear and damage, If the mini shaver shows signs
of wear or damage, do not use it as miury may
occur Do not use the mini skiver until Ft has been
replaced
Gently press the mmi shaver onto the skin.
Do not press too hard.
Hair Clipping
I Mike sure chat the appliance is fully charged
before you start clipping hair. The appliance
will not operate while cord is connected to
electrical outlet.
► Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
• Only use the appliance on dry hair.
I Do not use on freshly washed hair.
# Before you begin,comb the hair in the direction
of growth,
1 To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.

Clipping with hair comb attachment
H Put the hair clipper comb on the full width
trimmer attachment and push until you hear
it‘click’ into place (fig. 19).
H Press the Hair Length Selector and slide it to
the desired setting. See Table 2.
B The setting selected will appear in the
window to the left of the Hair Length
Selector (fig. 20).
When you are clipping for the first time, start
at the maximum clipping length setting (#9)
to familiarize yourself with the appliance and
prevent accidentally trimming hairs too short. As
you become familiar with the settings, adjust the
Hair Length Selector to desired trimming length.
Selector will ‘click’ into position at each setting.
Table 2. Hair Clipper
Setting Remaining hair length
(in)/(mm)
1 . 16 in./4mm
2
.24 in76mm
3
.31 in./8mm
4
.39 in./10mm
5
.47 in./12mm
6 .55 in./14mm
7 .63 in./16mm
8
.71 in./18mm
9 .79 in./20mm
□ Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (fig. 21 -22).
B Move the appliance slowly over the crown
from different directions to achieve an even
result (fig. 23).
H Always move the appliance against the
direction of hair growth.
fl Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
Q Turn the Groomer off and remove the hair
comb often to blow and/or shake out hair
that has accumulated.
I REMEMBER:You must reset the hair length
selector back to your desired setting every
time you replace the hair clipping comb on the
appliance.

Contouring without the hair clipping
comb attachment
fl Remove the hair comb by pressing and
sliding the Hair Length Selector upwards
(fig. 24).
Be careful when you are dipping without comb
attachment as when the appliance is turned on rl
will trim every hair it touches,
□ Tilt the appliance In sueh a way that only
one edge of the trimming attachment
touches the hair ends when you shape the
contours around the ears (fig. 25).
a To contour the nape of the neck or hairline,,
turn the appliance and hold it with the
trimming attachment pointing downwards
(fig. 24).
□ To contour the sideburns, turn the appliance
and hold It with the trimming attachment
pointing downwards (fig. 27).
Clearing
I Do not use water ora moist cloth to clean the
Groomer.
I Always switch Groomer OFF before cleaning.
I Do not use compressed air. abrasive cleaning
agents, scourers or liquids such as alcohol,
benzene, bleach or acetone to clean the
Groomer and attachments.
t Never clean* replace or remove Groomer
attachments with motor ON,
I Do not apply pressure to cutters.
> Do not touch cutters with hard objects as this
may damage them.
I Do not use while bathing, showering or
immerse the Groomer in water or other
iiquids as damage to Groomer may occur.

During Use:
I If cut hairs have accumulated in the Guide
Comb area, remove hairs by shaking, blowing
or using cleaning brush provided. Remember
to adjust the trimming length back to your
selected setting when you replace the comb on
Groomer.
After Each Use:
il Make sure the Groomer is switched OFF
and disconnected from the electrical outlet.
B Remove any attachment.
B Also separate the top part of the mini
shaver attachment from its body (fig. 28).
Q Blow and/or shake out any hair that may
have accumulated in the attachment.
I The shaving foil is very delicate and should not
be handled.
I If foil becomes damaged, replace it. Do not
apply pressure to shaving foil.
I Donot clean the foil with the brush, as this
may cause damage.
B Place the attachment back on the Groomer
or place it in the storage stand.
Rinsable Attachments
I If preferred your Groomer trimming
attachments (See Features©) can also be
rinsed clean after each use.
D Remove any attachment from Groomer and
rinse attachment only thoroughly under
warm tap water (fig. 29).
Never rinse attachments that are still attached to
the Groomer
B Shake excess water from attachment (fig. 30)
and allow to dry thoroughly.
Do not use a towel to dry the mini shaver as
damage to the shaving foil could occur.
B Place the attachment back on the Groomer
or place it in the storage stand.
This G roomer has no other user-serviceable parts.
For assistance call I -800-243-3050.

Storage
I Be sure Groomer is turned OFF, Remove
cord from outlet and Groomer/charging stand
before scoring in a safe, dry location where
it will not be crushed, banged, or subject to
damage.
P Store the Groomer and attachments in the
storage stand to prevent damage.
I Do not wrap cord around Groomer or stand
when storing.
P Store Cord in a safe location where it will not
be cut or damaged,
P Do not place or store Groomer where it can
fall or be pulled into a tub or sink, water or
other liquid while plugged m.
RepladngTrimmer Cuttiog Unit
If your cutter become damaged or worn, do not
corninue using the Groomcv Cull I-EI.DQ-243-305Q
for assistance.
Replacing The Hini Shaver Foil
tf ihe shaving foil is worn or damaged, do not
continue using the appliance. Replace the shaving
foil immediately
A worn or damaged shaving foil should only be
repfaced with an original Philips shaving foil. Call
l -300-243-3050 for assistance.
H Remove the detachable shaving head by
pulling it from the appliance (fig. 23).
Q Remove the shaving foil by pushing it out of
the shaving head (fig. 3 I).
Hi Place the new shaving foil carefully in the
shaving head {fig. 32).
El When the shaving foil is property positioned,
push it into its end position with your finger
(fig. 33).
Replacing The Mini Shaver Cutter
If the mini shaver cutter is worn or damaged, do
not continue using the appliance. Replace the mini
foil cutter and the shaving foil immediately
A worn or damaged mini shaver cutter should
only be replaced wtth an original Philips cutter
Call I -600-243-3050 for assistance.
0 Remove the detachable shaving head by
pulling it from the appliance (fig, 26),
IW Remove the old mini shaver cutter by pulling
it from the appliance (fig. 34).
Pi Make sure that the spring within the driving
unit does not get lost.
a Insert the new mini shaver cutter carefully
into the driving unit (fig. 35).
m When the mini shaver cutter is properly
positioned, push it into its end position wnh
your finger.
H Replace the detachable shaving head on the
appliance or place it in the storage stand.

Assistance
For assistance, call toll free:
1-800-243-3050
or visit our website:
www.philips.com/norelco
Information is available 24 hours a day,
7 days a week.
Battery Removal
I This Philips Norelco Groomer contains a
rechargeable Nickel-Cadmium battery, which
must be disposed of properly (fig. 36).
I Battery should only be removed when
Groomer is to be discarded.
I For assistance, call toll free: 1-800-243-3050 or
visit our website: www.philips.com/norelco.
H Unplug electrical cord from outlet and
Groomer before dismantling Groomer.
□ Allow the Groomer to run until the batteries
are completely empty/depleted. Turn
Groomer off.
Q Insert a narrow, flat blade screwdriver in the
groove next to the shaft at the top of the
Groomer (fig. 37).
□ Turn the screwdriver to separate the two
housing halves.
B Lift the battery out of the housing using the
screwdriver (fig. 38).
n Twist and bend the battery connections until
they break.
§1 Remove the battery from the Groomer.
O Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag. Discard
Groomer.
□ Contact your local town or city officials for
battery disposal information or call I-800-
8-BATTERY or www.rbrc.com for drop-off
locations.

000 1336 J
PHILIPS
NORELCO
45-DAY
MONEY-BACK
GUARANTEE
If yov are not fully iuHiified with your Philips Norelco
Groomer. send the product back and we'll refund you die
full purchase price,
Tfte CrtSmcr must Jse shipped prepaid by frtiHird
mail, mlurancc prepaid, and have the Original infer
receipt, indicating purchase price and the date of
purchase, enclosed, We cannot he responsible for lost
mail. The Groomer must he postmarked no foter than
45 days after the date of purchase. Philips Norefco
reserves the right to verify the purchase price of the
product and limit refunds not to exceed suggested
re toil price.
"Id obtain money-back guarantee return authorization form.
□ IE E-800-243-3050.
Full Two-Year Warranty
l-t.iips uecironc* fv>Ta flrveri-.j Coiporat-.fi w.nrana each new rvj ; : ,
Nwrteo pnxSjcl. Mattel Ol'rC. G365. G3 7 0 >;> ■ -i defects a malc«*h
W wodaiupmhp for * penqd rf t*U vnfln (cuften far up ( □ fa-ar
Ifam Ihe di’e of |auf thue. Jhd ifm Is 1 eS>a* or rc 0 |ate jpj JcfeCliw
pwlua wnhtiui tfurgtr
IMPORTANT: "hi* warranty does not ocw damage reKrtrtp.from
KoCtem. Or jfubr lock of 1 ertoruhlc Lire, Uh? .iH wr-^ □ ! any
.ir.iLl JT-;- '! rn.il fULvded wilfl ir-c t'Cnlu-J « of pJTEi Li
Ihe pra&ja to sny but she specie *Eft±fle.* Jse of uruuthensd
rrpUccmffnJ parts wil vod Ih.i warranty
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAT FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
HHME1UH5E THE CONSUMER FOR DAMAGE RESULTING PROM
WARRANTY SERVICE PERFORMED BY A NON. AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANT SPECIAL.
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
te letter it obun wam/Kf «n.ve, Rfflply 3a id ww*tpMpi.<ctf j J
nodM v call 1 -BCO-HHKC far iurttancc H a vijjgtsteti ihai far
jour prnbecton you rtlum shpmenf. af pmcUO by irA^red mad,
finj .mtr p»rp.L<J. t J.inLijjn eLYumrig Am-.,-, ihpmcnl 1 . nfit ttnwcrtrJ !.-,
LMis wamnlY NOTE bio ether warranty wniten or ail u anthemed
tft FtiAps flfrlramitL Nonft Ampia CdfTXvat.-Xbn Th-'i warranty ffVtt
you ipeciKi leyjiJ inn )».. isuijr .ilyo *jwe C'hct njfrtb aututh vary
from n'lie la Stile. Scrne SLUE-, aa <vy, a law We rai.Vjs*c/i a- fnvunan
of YXKtentdi on camequentuJ temupi sa U'-r jLo-o 1 ->•:_ ■ .j-,.&h and
Imtalioriy may nat appL to mu.
■ Read tndOSed rrCjutliOto gartAify
MonuiiaLred fee
FTifipi CpnujiTier Lifeslyfa
A Ukvneo IT. Ic-i tteilranc 1 Norm Amcncj Cc-rpcrilHSri
1 6 03^iviYtwr Street 5m fi»-.iQ.qV ■ O MflGS-. 1 2 5
bvNwl en life prMjOfl lUWpkllE ibreaM- H A
ien* • ' '"•••• • ' ‘ ' •
iMcroro 'b t nepitcred TraSranelt cFR4jn Ele-:t ™ iv.a
NOTH Airc -.f ' ‘‘VWKO'l
AccjCortrcf n a IraAiiarV of PFnips FlKtrurics tiarlh Amsnci Ccrpomitur
H-Ei.PS n 4 SlfAAtref Ti*tent*H> of rcru*^ Htcuw 10 NV
O WQ8 pFjfcpi Utttna FJcrlft Amcnti Co'po'flKbn At ’tc-jW.r-i