Philips NORELCO S7000 User manual

Shaver S7000
Tripleheader shaver

2
1
3
4
5
6
9
10
8
11
7
22
16 17
18 19 21
20
15
12
14
13
23

empty page before TOC

English 6
Español 45

English
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
-Do not reach for a corded product or SmartClean system that
has fallen into water. Unplug immediately from the power
outlet.
-Keep the power cord and SmartClean system dry.
-Do not place or store the product or Smartclean system
where it can fall or be pulled into a tub or sink. Do not place
or drop a SmartClean system into water or other liquid.
-Except when charging, always unplug this product from the
power outlet immediately after use.
-Remove power cord from power outlet and product before
cleaning.
-Plug power cord directly into power outlet. Do not use an
extension cord.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to
persons:
-Close supervision is required when this product is used by,
on, or near children, or persons with limited physical, sensory,
or mental capabilities or invalids.
6English

-Use this product for its intended household use as described
in this manual. Do not use attachments or cleaning cartridges
not recommended by Philips North America LLC.
-Never operate the product or SmartClean system if it has a
damaged power cord, if it is not working properly, after it has
been dropped or damaged, or after the product or power
cord has been dropped into water. For assistance call
1-800-243-3050.
-Keep the power cord away from heated surfaces.
-Never drop or insert any object into any opening.
-Do not use the power cord in or near a power outlet that
contains an electric air freshener to prevent damage to the
power cord.
-Be careful when handling your smartphone near water and in
moist environments.
-The shortwave radio frequency signals of a Bluetooth®
product may impair the operation of other electronic and
medical devices.
-Switch off Bluetooth where it is prohibited.
-Do not use the product in medical facilities, aircraft, refuelling
points, close to automatic doors, automatic fire alarms or
other automatically controlled devices.
-Keep this product at least 8 inches from pacemakers and
other medical devices. Radio waves may impair the operation
of pacemakers and other medical devices.
-Do not charge or plug in product or SmartClean system
outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
-Always check cutters and combs before using the product.
Do not use the product if cutters or combs are damaged, as
injury may occur.
7
English

-Always attach power cord to product or SmartClean system
first, then to power outlet. To disconnect, set all controls to
'off' position. Then remove power cord from power outlet.
-Only use the power cord and other accessories supplied with
the product.
-Do not attempt to open the product to remove or replace the
built-in rechargeable battery.
-The batteries used in this product may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug as this will
cause a hazardous condition.
Electromagnetic fields (EMF)
This Philips product complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
FCC Compliance
-The frequency band in which the appliance
operates is 2.4 GHz.
-This appliance is equipped with Bluetooth
class 2
-The maximum radio frequency power
radiated in the frequency band in which the
appliance operates is less than 20 dBm
-This device complies with the FCC RF
exposure limits and has been evaluated in
compliance with portable exposure
condition.
Changes or modifications not expressly
approved by Philips could void the users's
authority to operate the equipment.
8English

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:(1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the
equipment and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
9
English

-Consult the dealer or an experienced
radio/TV technician for help”
The Bluetooth® wordmark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Koninklijke Philips N.V. is under license.
-There is no limitation as to which distance
can be used from the human body.
SAVE THESE
INSTRUCTIONS
General description (Fig. 1)
1 Click-on precision trimmer attachment
2 Click-on shaving unit
3 On/off button
4 Notification symbol
5 Sensitive shave setting XS
6 Sensitive shave setting S
7 Cleaning reminder
8 Travel lock symbol
9 Unplug for use reminder
10 Battery charge indicator
11 Inlet for small plug
12 Power cord
13 Cleaning brush
14 Small plug
15 Cap of SmartClean system
16 SmartClean system
17 On/off button
18 Replacement symbol
19 Rinsing symbol
20Ready symbol
10 English

21 Battery symbol
22 Cleaning cartridge for SmartClean system
23 Travel case
Note: The accessories supplied may vary for
different products. The box shows the
accessories that have been supplied with your
product.
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benefit from the
support that Philips offers, register your
product easily via the app or at
http://www.philips.com/s7000-support.
Download the GroomTribe app to create your
Personal Shaving Plan today. It will provide
you ongoing guidance on how to tackle your
skin issue. The app also tracks your shaving
routine and adjusts your shaver's settings in
line with your plan.
The display
Notification symbol
The shaver is equipped with a notification
symbol. The notification symbol lights up when
there is an important message for you in the
app. When it lights up, simply open the app on
your smartphone and follow the easy tips that
the app gives you. If you need further support,
visit www.philips.com/s7000-support.
11
English

Sensitive shave settings
The shaver has a feature that allows you to
personalize your shave settings using the app.
Choose between three settings depending on
your personal shaving needs: extra sensitive
(xs), sensitive (s) and normal. Select your
preferred setting 'xs', 's' or 'normal' in the app
to activate it on your shaver. By default the
setting is set on sensitive (s).
Note: The sensitivity settings can only be
adjusted by using the app.
Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
The cleaning reminder flashes to remind you
to clean the shaver.
Travel lock
3 sec.
When you are going to travel, you can lock the
shaver to prevent it from accidentally
switching on. The travel lock also deactivates
Bluetooth.
'Unplug for use' reminder
The ‘unplug for use’ reminder flashes to
remind you to disconnect the shaver from the
wall outlet before you can switch it on.
12 English

Note: This shaver is waterproof. It is suitable
for use in the bath or shower and for cleaning
under the tap. For safety reasons, the shaver
can only be used without cord.
Charging
Quick charge: After approx. 5 minutes of
charging, the shaver contains enough power
for one shave. At that moment, the battery
charge indicator stops flashing quickly and
starts flashing slowly.
When the shaver continues charging, the
battery charge indicator on the shaver flashes
white slowly.
Battery fully charged
When the battery is fully charged, the battery
charge indicator lights up white continuously.
Note: When the battery is full, the display
switches off automatically after 30 minutes.
Note: The shaver can only be used without a
cord. If you press the on/off button during
charging, the unplug for use reminder lights up
white to remind you that you have to
disconnect the shaver from the wall outlet.
13
English

Battery low
When the battery is almost empty, the battery
charge indicator flashes orange. At this point
there is enough energy left for one shave.
Bluetooth® connection
The shaver is equipped with Bluetooth® 4.1 to
connect your shaver to the app. Bluetooth is
automatically activated when you switch on
the shaver for the first time.
3 sec.
You can only deactivate it by activating the
travel lock.
Note: Make sure your smartphone is equipped
with Bluetooth 4.1 or higher.
Charging
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 50 minutes.
Note: You cannot use the shaver while it is
charging.
Quick charge
After approx. 5 minutes of charging the shaver
contains enough power for one shave.
14 English

Charging with the power cord
1Make sure the shaver is switched off.
1
2
2Put the small plug in the shaver and put the
power cord in the wall outlet.
The display of the shaver indicates that the
shaver is charging.
3After charging, remove the power cord from
the wall outlet and pull the small plug out of
the shaver.
Note: When the battery is full, the display
switches off automatically after 30 minutes.
Charging in the SmartClean system
1
2
1Put the small plug in the back of the
SmartClean system.
2Put the supply unit in the wall outlet.
3Press to open the SmartClean system cap,
to be able to place the shaver in the holder
('click').
4Hold the shaver upside down above the
holder. Make sure the front of the shaver
points towards the SmartClean system
holder.
15
English

1
23
5Place the shaver in the holder, tilt the
shaver backwards and press down the
SmartClean system cap to connect the
shaver (‘click’). The battery symbol flashes
to indicate that the shaver is charging.
When the battery is fully charged, the
battery symbol lights up continuously.
Preparing for use
Pair the shaver and smartphone
The app is compatible with a wide range of
iPhone and Android™ smartphones.
More information is available at
www.philips.com/s7000-support.
1Download the app from your app store.
S7920
2Make sure Bluetooth on the smartphone is
switched on.
3Switch on the shaver.
4Open the app and follow the instructions to
start the pairing process.
5When paired, the shaver and app will
connect automatically when you open the
app. Simply keep the app open and
Bluetooth on.
16 English

Unpair the shaver and smartphone
Pairing allows a connection between 1 shaver
and 1 smartphone. To remove this connection
(e.g. when you have a new smartphone), use
the following steps:
1Unpair the shaver: press and hold the
on/off button on the handle for approx. 10
seconds to remove the bond between
shaver and app.
Note: The unpairing of the shaver is
successful when the notification symbol
lights up 4 times briefly.
2Unpair your smartphone: go to 'Settings' on
your smartphone and select Bluetooth.
Then select ' Shaver S79xx' and press
'forget' or 'unpair'.
Note: The unpairing procedure may vary per
smartphone. Please check your smartphone
manual for more information.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
Note: This shaver is waterproof. It is suitable
for use in the bath or shower and for cleaning
17
English

under the tap. For safety reasons, the shaver
can only be used without cord.
21-day adaption process
-21 Day Trial and Conversion Process. It is a
fact that your skin and beard need time to
adjust to a new grooming system.
-Use your new shaver exclusively for 3 weeks
to fully enjoy the closeness of a Philips
Norelco shave.
-At first you may not get as close a shave as
you expect, or your face may even become
slightly irritated. This is normal since your
beard and skin will need time to adjust.
Invest 3 weeks and you'll soon experience
the full joy of your new shaver.
-Stick with it! If you alternate shaving
methods during the adjustment period, it
may make it more difficult to adapt to the
Philips Norelco shaving system.
-If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
Switching the shaver on and off
1To switch on the shaver, press the on/off
button once.
2To switch off the shaver, press the on/off
button once.
18 English

Connect with the shaver
1Make sure Bluetooth on the smartphone is
switched on.
2Open the app on the smartphone.
3When paired (see 'Pair the shaver and
smartphone'), the shaver and the app will
connect automatically. You can now start
shaving.
Note: Make sure you have a good Bluetooth
and Internet connection to fully benefit
from the app.
4Keep the smartphone and shaver close to
each other in order to stay connected and
synchronize your shaves.
Synchronize your shaves
The shaver can store data of up to 20 shaves,
so you don't have to shave with your phone
near you every time. However, to prevent data
loss, synchronize the shaver with the app once
every 20 shaves.
1Make sure you are close to the shaver and
open the app.
2The app connects automatically and
synchronizes your last shaves.
Shaving advice
There are 2 ways to obtain advice: guided
shave real time or synchronized shave. We
advise you to start with the guided shave to
enhance your shaving experience. Correct
handling of your shaver will contribute to the
best shaving result. Next, follow the advice
19
English

obtained from the synchronized shaves and
the personalized programs.
Shaving
Shaving tips
-For the best results on skin comfort, pre-
trim your beard if you have not shaved for 3
days or longer.
-Move the shaving heads over your skin in
circular movements.
-Keep each shaving head fully in contact
with your skin.
-Exert gentle pressure for a close,
comfortable shave.
Dry shaving
1Switch on the shaver.
2Move the shaving heads over your skin in
circular movements to catch all hairs
growing in different directions. Make sure
each shaving head is fully in contact with
the skin. Exert gentle pressure for a close,
comfortable shave.
Note: Do not press too hard, as this can
cause skin irritation.
3Switch off and clean the shaver after each
use (see 'Cleaning and maintenance').
Wet shaving
For a more refreshing shave, you can also use
this shaver on a wet face with a shaving gel or
foam for sensitive skin.
20 English