Philips RQ1100 Series User manual

Register your product and get support at
www.philips.com/welcome
RQ1100 series
4222_002_5349_2_DFU-Luxury_A6_v2.indd 1 2-7-2012 12:49:48

4222_002_5349_2_DFU-Luxury_A6_v2.indd 2 2-7-2012 12:49:48

1
4222_002_5349_2_DFU-Luxury_A6_v2.indd 3 2-7-2012 12:49:49

1
4222_002_5349_2_DFU-Luxury_A6_v2.indd 4 2-7-2012 12:49:49

RQ119x, RQ118x, RQ117x, RQ116x, RQ115x, RQ114x, RQ113x
ENGLISH 6
简体中文 35
4222_002_5349_2_DFU-Luxury_A6_v2.indd 5 2-7-2012 12:49:49

6
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at www.philips.com/
welcome.
Please read this user manual, as it contains information
about the features of this shaver as well as some tips
to make shaving easier and more enjoyable.
General description (Fig. 1)
A Shaver
1 Display
2 Shaver on/off button
3 Protection cap
4 RQ11 Shaving unit
B CRP331 Trimmer (RQ118x/RQ116x/RQ115x
only)
C RQ111 Beard Styler attachment (RQ1195/
RQ1185/RQ1175 only)
1 Hair length selector
2 Comb of Beard Styler attachment
D Jet Clean System (RQ1195CC/RQ1185CC/
RQ1180CC/RQ1175CC only)
1 Shaver holder
2 ’Cleaning chamber empty’ symbol
3 Cleaning symbol
4 Drying symbol
5 Jet Clean System on/off button
6 Cleaning chamber release button
E Adapter
F Charger
G Cleaning brush
H HQ200 Cleaning uid (specic types only)
I Pouch (specic types only)
ENGLISH
4222_002_5349_2_DFU-Luxury_A6_v2.indd 6 2-7-2012 12:49:49

Important
Read this user manual carefully before you use the
shaver and the Jet Clean System and save it for
future reference.
Note: In this user manual the term ‘appliances’ refers
to the shaver and the Jet Clean System. If your shaver
does not come with a Jet Clean System, it refers to the
shaver only.
General
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- These appliances are not intended for use
by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use of
these appliances by a person responsible for their
safety.
- Children should be supervised to ensure that they
do not play with the shaver and the Jet Clean
System.
- Be careful with hot water when you clean the
appliances. Always check if the water is not too
hot, to prevent your hands from getting burnt.
Caution
- Never immerse the Jet Clean System and the
charger in water nor rinse them under the tap.
- The appliances and accessories are not
dishwasher-proof.
ENGLISH 7
4222_002_5349_2_DFU-Luxury_A6_v2.indd 7 2-7-2012 12:49:50

- Always place and use the appliances on a surface
that is uid-resistant.
- Use, charge and store the shaver at a temperature
between 5°C and 35°C.
- Only use the accessories supplied with this shaver
or that have been specically developed for this
shaver.
- If the adapter or any of the other accessories is
damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
- Do not use the appliances and accessories if they
are damaged.
- Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Jet Clean system (specic types only)
Caution
- Only use the Jet Clean System with the original
HQ200 cleaning uid.
- Always place and use the Jet Clean System on a
stable, level and horizontal uid-resistant surface
to prevent leakage.
- Never immerse the Jet Clean System in water.
- Empty the cleaning chamber and clean it thoroughly
by rinsing it with hot tap water every 15 days.
- The Jet Clean System thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
- The cleaning chamber of the Jet Clean System is
not dishwasher-proof.
- When the Jet Clean System is ready for use, do
not move it to prevent leakage of cleaning uid.
ENGLISH8
4222_002_5349_2_DFU-Luxury_A6_v2.indd 8 2-7-2012 12:49:50

Beard Styler attachment (specic types
only)
Caution
- Only use the Beard Styler attachment to trim
facial hair (beard, moustache and sideburns). Do
not use it to trim body parts below the neckline.
- Only use the Beard Styler attachment in
combination with the following shaver types:
RQ12xx,RQ11xx, RQ10xx.
- The Beard Styler attachment is not dishwasher-
proof.
Compliance with standards
- This shaver complies with the internationally
approved safety regulations and can be safely used
in the bath or shower and cleaned under the tap.
- These Philips appliances comply comply with
all standards regarding electromagnetic elds
(EMF). If handled properly and according to the
instructions in this user manual, the appliances are
safe to use based on scientic evidence available
today.
The display
Note: If there is a protective foil on the display, remove
it before you use the shaver for the rst time.
The various shaver types have different displays,
which are shown in the gures below.
ENGLISH 9
4222_002_5349_2_DFU-Luxury_A6_v2.indd 9 2-7-2012 12:49:50

- RQ1195/RQ1180/RQ1175
- RQ1185/RQ1160
- RQ1155/RQ1151/RQ1150/RQ1145/RQ1141/
RQ1131
Charging
- Charging takes approx. 1 hour.
RQ1195/RQ1180/RQ1175
- When the shaver is charging, rst the bottom
charging light ashes, then the second charging
light, and so on until the shaver is fully charged.
- Quick charge:When the shaver contains enough
energy for one shave, the bottom charging light
alternately ashes orange and white.
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
ENGLISH10
4222_002_5349_2_DFU-Luxury_A6_v2.indd 10 2-7-2012 12:49:52

- When the shaver is charging, rst the plug symbol
and the battery symbol ash alternately. After
some time, the plug symbol goes out and the
battery symbol continues to ash until the shaver
is fully charged.
- Quick charge:When the shaver contains enough
energy for one shave, the alternate ashing of the
plug symbol and battery symbol stops and only
the battery symbol ashes.
Battery fully charged
RQ1195/RQ1180/RQ1175
- When the battery is fully charged, all charging
lights light up continuously. After approx. 30
minutes, the display automatically switches off
again.
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
- When the battery is fully charged, the battery
symbol lights up continuously. After approx. 30
minutes, the display automatically switches off
again.
Battery low
RQ1195/RQ1180/RQ1175
- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the
bottom charging light ashes orange.
- When you switch off the shaver, the bottom
charging light continues to ash for a few seconds.
ENGLISH 11
4222_002_5349_2_DFU-Luxury_A6_v2.indd 11 2-7-2012 12:49:53

RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the plug
symbol ashes.
- When you switch off the shaver, the plug
symbol continues to ash for a few seconds.
Remaining battery capacity
RQ1195/RQ1180/RQ1175
- The remaining battery capacity is indicated by the
number of charging lights that are on.
Travel lock
You can lock the shaver when you are going to
travel.The travel lock prevents the shaver from being
switched on by accident.
Activating the travel lock
1 Press the on/off button for 3 seconds to enter
the travel lock mode.
,The lock symbol lights up on the display.
Note:The displays of the various shaver types look
different, but show the same symbol.
Deactivating the travel lock
1 Press the on/off button for 3 seconds.
,The motor starts running to indicate that the
travel lock has been deactivated.
The shaver is now ready for use again.
ENGLISH12
4222_002_5349_2_DFU-Luxury_A6_v2.indd 12 2-7-2012 12:49:55

Note:When you place the shaver in the plugged-
in charger or Jet Clean System, the travel lock is
automatically deactivated.
Replace shaving head holder
Note:The displays of the various shaver types look
different, but show the same symbol.
For maximum shaving performance, we advise you
to replace the shaving head holder every two years.
- To remind you to replace the shaving head holder,
the appliance is equipped with a replacement
reminder which is activated automatically after
approx. two years.The replacement reminder is
repeated at 9 successive shaves or until you reset
the shaver.
Charging
Charging takes approx. 1 hour.
RQ1195/RQ1185/RQ1180/RQ1175/RQ1160/
RQ1155: A fully charged shaver has a shaving time of
up to 50 minutes or 15 days.
RQ1151/RQ1150/RQ1145: A fully charged shaver
has a shaving time of up to 45 minutes or 13 days.
RQ1141/RQ1131: A fully charged shaver has a
shaving time of up to 40 minutes or 12 days.
Charge the shaver before you use it for the rst
time and when the display indicates that the battery
is almost empty (see section ‘Battery low’ in chapter
‘The display’).
Quick charge
After the shaver has charged for 5 minutes,
it contains enough energy for one shave.
ENGLISH 13
4222_002_5349_2_DFU-Luxury_A6_v2.indd 13 2-7-2012 12:49:55

Charging in the charger
1 Insert the small plug into the charger.
2 Unfold the charger (‘click’).
3 Put the adapter in the wall socket.
4 Put the shaver in the charger (1) and press it
backwards until it locks into place (2).
,The display shows that the shaver is charging
(see section ‘Charging’ in chapter ‘The display’).
Charging in the Jet Clean System (specic
types only)
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Hold the shaver upside down above the holder
with the back of the shaver pointing towards
the holder.
Note: RQ1195/RQ1180/RQ1175: when you turn the
shaver upside down, the battery indication on the
display is also turned upside down so you can still see
to what level the battery is charged.
ENGLISH14
4222_002_5349_2_DFU-Luxury_A6_v2.indd 14 2-7-2012 12:49:56

4 Place the shaver body in the holder behind the
two clips (1) and press it down until it locks
into place (2).
Note:The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit
or when the trimmer is placed on the shaver.
,The display shows that the shaver is charging
(see chapter ‘The display’).
Using the shaver
Shaving
Skin adaptation period
Your rst shaves may not bring you the result you
expect and your skin may even become slightly
irritated.This is normal.Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times
a week) for a period of 3 weeks to allow your skin
to adapt to the new shaver. During this period, use
your new electric shaver exclusively and do not use
other shaving methods. If you use different shaving
methods, it is more difcult for your skin to adapt to
the new shaving system.
1 Press the on/off button once to switch on the
shaver.
,RQ1195/RQ1180/RQ1175:The display lights up
for a few seconds.
ENGLISH 15
4222_002_5349_2_DFU-Luxury_A6_v2.indd 15 2-7-2012 12:49:57

2 Move the shaving heads over your skin in
circular movements.
- Do not make straight movements.
3 Press the on/off button once to switch off the
shaver.
,RQ1195/RQ1180/RQ1175:The display lights up
for a few seconds and then shows the remaining
battery capacity.
Wet shaving
You can also use this shaver on a wet face with
shaving foam or shaving gel.
To shave with shaving foam or shaving gel, follow the
steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4 Press the on/off button once to switch on the
shaver.
5 Move the shaving heads over your skin in
circular movements.
Note: Rinse the shaver under the tap regularly to
ensure that it continues to glide smoothly over your
skin.
6 Dry your face and thoroughly clean the
shaver after use (see chapter ‘Cleaning and
maintenance’).
Note: Make sure you rinse all foam or shaving gel off
the shaver.
ENGLISH16
4222_002_5349_2_DFU-Luxury_A6_v2.indd 16 2-7-2012 12:49:58

Using the trimmer (specic types only)
You can use the trimmer to groom your sideburns
and moustache.
1 Pull the shaving unit straight off the shaver.
Note: Do not twist the shaving unit while you pull it off
the shaver.
2 Insert the lug of the trimmer into the slot in
the top of the shaver (1).Then press down the
trimmer (2) to attach it to the shaver (‘click’).
3 Press the on/off button once to switch on the
trimmer.
,RQ1180:The display lights up for a few seconds.
4 You can now start trimming.
5 Press the on/off button once to switch off the
trimmer.
,RQ1180:The display lights up for a few seconds
to show the remaining battery capacity.
6 Pull the trimmer straight off the shaver.
Note: Do not twist the trimming unit while you pull it
off the shaver.
7 Insert the lug of the shaving unit into the slot
in the top of the shaver (1).Then press down
the shaving unit (2) to attach it to the shaver
(‘click’).
Using the Beard Styler attachment (specic
types only)
Note: Only use the Beard Styler attachment to trim
facial hair (beard, moustache and sideburns). Do not
use it to trim body parts below the neckline.
ENGLISH 17
4222_002_5349_2_DFU-Luxury_A6_v2.indd 17 2-7-2012 12:49:59

1 Make sure the shaver is switched off.
2 Pull the shaving unit straight off the shaver.
Note: Do not twist the shaving unit while you pull it off
the shaver.
3 Insert the lug of the Beard Styler
attachment into the slot in the top of the
shaver (1).Then press down the Beard Styler
attachment (2) to attach it to the shaver
(‘click’).
Using the Beard Styler attachment with
comb
You can use the Beard Styler attachment with the
comb attached to style your beard at one xed
setting, but also at different length settings.The
hair length settings on the Beard Styler attachment
correspond to the remaining hair length after cutting
and range from 1 to 5mm.
1 Slide the comb straight into the guiding
grooves on both sides of the Beard Styler
attachment (‘click’).
2 Press the length selector (1) and then push it
to the left or right (2) to select the desired
hair length setting.
3 Press the on/off button on the shaver to switch
it on.
ENGLISH18
4222_002_5349_2_DFU-Luxury_A6_v2.indd 18 2-7-2012 12:50:01

4 You can now start styling your beard.
Using the Beard Styler attachment without
comb
You can use the Beard Styler attachment without the
comb to trim and contour your beard, moustache or
sideburns.
1 Pull the comb off the Beard Styler attachment.
Note: Grab the comb in the centre to pull it off the
Beard Styler attachment. Do not pull at the sides of the
comb.
2 Press the on/off button to switch on the shaver.
3 You can now start to trim and contour your
beard, moustache, sideburns or neckline.
Beard styles
Below you nd some examples of beard styles you
can create.
- A stubble look
ENGLISH 19
4222_002_5349_2_DFU-Luxury_A6_v2.indd 19 2-7-2012 12:50:03

- A full beard
- A moustache
- A goatee
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as petrol or acetone to
clean the shaver, its accessories and the Jet Clean
System (specic types only).
- The best and most hygienic way to clean the
shaver is in the Jet Clean System (specic types
only).You can also rinse the shaver under the tap
or clean it with the brush supplied.
- Clean the shaver after every shave for optimal
shaving performance.
- You can clean the outside of the shaver with a
damp cloth.
- Regular cleaning guarantees better shaving
performance.
ENGLISH20
4222_002_5349_2_DFU-Luxury_A6_v2.indd 20 2-7-2012 12:50:06