Philips RQ1200 series User manual
Register your product and get support at
www.philips.com/welcome
Always here to help you
User manual
RQ1200 series
1
6
General description (Fig. 1)
A Shaver
1 Display
2 Shaver on/off button
3 Protection cap
4 RQ12 Shaving unit
5 Trimmer
6 Trimmer on/off slide
B Foldable charger
1 ’Cleaning chamber empty’ symbol
2 Cleaning symbol
3 Drying symbol
4 Jet Clean System on/off button (RQ1008 only: up/down button
5 Cleaning chamber release button
6 Shaver holder
D Cleaning brush
F Pouch
G Adapter
The various shaver types have different displays, which are shown in the
- RQ1290/RQ1280
- RQ1260
- RQ1250
MINUTES LEFT
MINUTES LEFT
ENGLISH
-
RQ1290/RQ1280
-
-
- Quick charge:When the shaver contains enough energy for one shave,
RQ1260/RQ1250
-
then the second charging light, and so on until the shaver is fully
- Quick charge:When the shaver contains enough energy for one shave,
RQ1290/RQ1280
- When the battery is fully charged, the minutes indication lights up
RQ1260/RQ1250
- When the battery is fully charged, all charging lights light up
RQ1290/RQ1280
- When the battery is almost empty (when there are only 5 or fewer
-
ENGLISH 7
RQ1260/RQ1250
- When the battery is almost empty (when there are only 5 or fewer
- When you switch off the shaver, the bottom charging light continues to
RQ1290/RQ1280
- The remaining battery capacity is indicated by the number of shaving
RQ1260/RQ1250
-
For optimal shaving performance, we advise you to clean the shaver after
-
For maximum shaving performance, we advise you to replace the shaving
- To remind you to replace the shaving unit, the appliance is equipped
with a replacement reminder which is activated automatically after
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
ENGLISH8
1 Press the on/off button for 3 seconds to enter the travel lock mode.
,RQ1280:The display starts to count down from 3.At 1, the appliance
beeps to indicate that it is locked.
,The lock symbol lights up on the display.After a few seconds it goes
out.
1 Press the on/off button for 3 seconds.
,The motor starts running to indicate that the travel lock has been
deactivated.
the shaver enters the power-saving mode, the light in the on/off button
- When the appliance is switched off but detects movement for 5
minutes (for instance when you are travelling with the shaver in your
,
is in power-saving mode.
-
- If the shaving heads are blocked, the shaving unit symbol, the tap
-
- The shaving unit symbol, the tap symbol and the exclamation mark
RQ1290/RQ1280/RQ1260: A fully charged shaver has a shaving time of up
RQ1250: A fully charged shaver has a shaving time of up to 50 minutes or
indicates that the battery is almost empty (see section ‘Battery low’ in
MINUTES LEFT
MINUTES LEFT
ENGLISH 9
After the shaver has charged for 5 minutes, it contains enough energy for
1 Insert the small plug into the charger.
2 Unfold the charger (‘click’).
3 Put the adapter in the wall socket.
4 Put the shaver in the charger.
,The display shows that the shaver is charging (see chapter ‘The
display’).
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Hold the shaver upside down above the holder with the back of the
shaver pointing towards the holder.
4 Place the shaver body in the holder behind the two clips (1) and
press it down until it locks into place (2).
,The display shows that the shaver is charging (see section ‘Charging’
in chapter ‘The display’).
use your new electric shaver exclusively and do not use other shaving
1 Press the on/off button once to switch on the shaver.
,The display lights up for a few seconds.
ENGLISH10
2 Move the shaving heads over your skin in circular movements.
-
3 Press the on/off button once to switch off the shaver.
,The display lights up for a few seconds and then shows the remaining
battery capacity.
To shave with shaving foam or shaving gel, follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure that the shaving unit
glides smoothly over your skin.
4 Press the on/off button once to switch on the shaver.
5 Move the shaving heads over your skin in circular movements.
6 Dry your face and thoroughly clean the shaver after use (see chapter
‘Cleaning and maintenance’).
1 Pull the shaving unit straight off the shaver.
2 Press the on/off button once to switch on the shaver.
,The display lights up for a few seconds.
3 Slide the trimmer slide forwards to slide out the trimmer.
4 You can now start trimming.
5 Slide the trimmer slide backwards to retract the trimmer.
6 Press the on/off button once to switch off the shaver.
,The display lights up for a few seconds and shows the remaining
battery capacity.
ENGLISH 11
7 Insert the lug of the shaving unit into the slot in the top of the shaver
(1).Then press down the shaving unit (2) to attach it to the shaver
(‘click’).
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the shaver, its accessories and the Jet
- The best and most hygienic way to clean the shaver is in the Jet Clean
-
-
-
-
Be careful with hot water.Always check if the water is not too hot, to
prevent your hands from getting burnt.
1 Rinse the shaving unit under a hot tap for some time.
2 Pull open the three shaving heads one by one.
ENGLISH12
3 Rinse all three shaving heads and all three hair chambers under a hot
tap for 30 seconds.
Be careful with hot water.Always check if the water is not too hot, to
prevent your hands from getting burnt.
4 Carefully shake off excess water and leave the shaving heads open to
let the shaving unit dry completely.
Never dry the shaving unit with a towel or tissue, as this may damage the
shaving heads.
The Jet Clean System comes in two types:
- Type RQ1008 has three cleaning programs: the eco program, the auto
-
press the on/off button, the Jet Clean System starts cleaning in the
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
,The holder automatically moves to the highest position.
3 Simultaneously press the release buttons on both sides of the
cleaning chamber (1).Then lift the Jet Clean System off the cleaning
chamber (2).
,The cleaning chamber remains behind.
4
between the two lines.
5 Place the Jet Clean System back onto the cleaning chamber.
ENGLISH 13
1 Hold the shaver upside down above the holder with the back of the
shaver pointing towards the holder.
2 Place the shaver body in the holder behind the two clips (1) and
press it down until it locks into place (2).
,The display shows that the shaver is charging (see chapter ‘The
display’).
3 RQ1008: Press the up/down button to select a cleaning program.
4 Press the on/off button on the Jet Clean System to start the cleaning
program.
,The shaver display stops showing the charging indication.
,
,
takes a few minutes.
,
automatically switches on and off several times and moves up and
down.
,During the second phase of the cleaning program, the shaver is
This phase takes approx. 2 hours.The shaver stays in this position
until the end of the program.
,After the cleaning program, the charging indication appears on the
shaver display (see chapter ‘The display’).
ENGLISH14
-
- If you use the Jet Clean System to clean your shaver every day, you
1 Simultaneously press the release buttons on both sides of the Jet
Clean System (1).Then lift the Jet Clean System off the cleaning
chamber (2).
,The cleaning chamber remains behind.
2
3 Rinse the cleaning chamber under the tap.
The cleaning chamber is not dishwasher-proof.
4
between the two lines.
5 Place the Jet Clean System back onto the cleaning chamber.
Make sure the appliance is switched off.
1 Pull the shaving unit straight off the shaver.
2 Pull open the three shaving heads one by one.
3 Press the retainer release tab (1) until the retainer opens (2).
ENGLISH 15
4 Remove the cutter from the shaving guard.
5 Clean the cutter with the cleaning brush supplied.
6 Clean the inside of the shaving guard.
7 After cleaning, place the cutter back into the shaving guard with the
cutter legs pointing downwards.
8 Press down the retainer over the cutter.
9 Close the shaving heads.
ENGLISH16
10 Insert the lug of the shaving unit into the slot in the top of the shaver
(1).Then press the shaving unit downwards (2) to attach it to the
shaver (‘click’).
1 Slide the trimmer slide forwards to slide out the trimmer.
2 Rinse the trimmer under a hot tap for some time.
3 Slide the trimmer slide backwards to retract the trimmer.
Replacement
For maximum shaving performance, we advise you to replace the shaving
1
(RQ129x/RQ128x only) when you switch off the shaver .
2 Pull the old shaving unit straight off the shaver.
3 Insert the lug of the new RQ12 shaving unit into the slot in the top
of the shaver (1).Then press down the shaving unit (2) to attach it to
the shaver (‘click’).
4 RQ128x/RQ127x/RQ126x/RQ125x:To reset the shaver, press and
hold the on/off button for approx. 10 seconds.
MINUTES LEFT
MINUTES LEFT
ENGLISH 17
18
- RQ1290, RQ1280
- RQ1260
- RQ1250
MINUTES LEFT
MINUTES LEFT
-
RQ1290, RQ1280
-
-
-
RQ1260, RQ1250
-
-
RQ1290, RQ1280
-
RQ1260, RQ1250
-
RQ1290, RQ1280
-
-
19
RQ1260, RQ1250
-
-
RQ1290, RQ1280
-
RQ1260, RQ1250
-
-
-
RQ1250)
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
20
Other manuals for RQ1200 series
9
This manual suits for next models
5
Table of contents
Languages:
Other Philips Electric Shaver manuals
Philips
Philips 43PUT6002/56 User manual
Philips
Philips Norelco QC5580 User manual
Philips
Philips HQ6730 User manual
Philips
Philips HQ7782/16 User manual
Philips
Philips S5214/06 User manual
Philips
Philips S5420 User manual
Philips
Philips SENSOTEC HQ8890 User manual
Philips
Philips Norelco HS8420 User manual
Philips
Philips HQ7120 User manual
Philips
Philips Norelco Speed-XL 8140XL User manual
Philips
Philips 8240XL User manual
Philips
Philips RQ1050 with charger User manual
Philips
Philips Norelco 9300 Instruction Manual
Philips
Philips S7000 series User manual
Philips
Philips HQ9140 User manual
Philips
Philips HQ644 User manual
Philips
Philips HQ6640 User manual
Philips
Philips T 388 User manual
Philips
Philips S7000 series Installation guide
Philips
Philips HQ914 User manual
