Philips SP9820/18 User manual

SP9820
www.philips.com/support/ifu-lux
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Philips Shaver Series 9000
Wet&Dry SP9820/18 o cerca il tuo prodotto tra le migliori offerte di Cura della Persona

3
2
1
17
16
15
14
13
12
11
10
9
6
5
4
8
7
SP98xx/12

empty page before TOC

English 6
Deutsch 29
Español 56
Français 81
Italiano 107

English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the features of this shaver as
well as some tips to make shaving easier and more
enjoyable.
General description (Fig. 1)
1 Supply unit
2 Small plug
3 Pouch
4 Socket for small plug
5 Unplug for use symbol
6 Replacement reminder
7 Notification symbol
8 Cleaning reminder
9 Travel lock symbol
10 Battery charge indicator
11 Battery charge percentage
12 Personal comfort settings bar
13 Personal comfort settings decrease button
14 Personal comfort settings increase button
15 On/off button
16 Shaving unit with hair chamber
17 Click-on precision trimmer attachment
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
6English

Danger
- Keep the supply unit dry.
Warning
- To charge the battery, only use the
detachable supply unit (HQ8505) provided
with the appliance.
- The supply unit contains a transformer. Do
not cut off the supply unit to replace it with
another plug, as this causes a hazardous
situation.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not play
with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
7
English

- Always unplug the shaver before you clean
it under the tap.
- Always check the appliance before you use
it. Do not use the appliance if it is damaged,
as this may cause injury. Always replace a
damaged part with one of the original type.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Never use water hotter than 60°C to rinse
the shaver.
- Only use this appliance for its intended
purpose as shown in the user manual.
- For hygienic reasons, the appliance should
only be used by one person.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive
liquids such as petrol or acetone to clean
the appliance.
- Water may drip from the socket at the
bottom of the shaver when you rinse it. This
is normal and not dangerous because all
electronics are enclosed in a sealed power
unit inside the shaver.
8English

- Do not use the supply unit in or near wall
sockets that contain an electric air freshener
to prevent irreparable damage to the supply
unit.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the
tap. For safety reasons, the shaver can
therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
The display
Note: Remove any sticker or protective foil from
the display before using the product.
Charging
When the shaver is charging, the battery charge
indicator on the shaver flashes white.
The battery charge is indicated by the battery
charge percentage flashing on the display, which is
shown when the shaver is moved.
Quick charge: After approx. 5 minutes charging, the
shaver contains enough energy for one shave.
9
English

Battery fully charged
When the battery is fully charged, the battery
charge indicator lights up white continuously.
Note: When the battery is full, the display switches
off automatically after 15 minutes.
The battery charge percentage lights up white
continuously when the shaver is moved.
Battery low
When the battery is almost empty, the battery
charge indicator flashes orange and the shaver
beeps. At this point there is enough energy left for
one shave..
Remaining battery charge
The remaining battery charge is indicated by the
battery charge percentage shown on the display.
Personal comfort settings
The shaver has a feature that allows you to
personalize your settings. Depending on your
personal shaving needs, choose between three
settings, from low to high: comfort, dynamic or
efficiency. When you press the button on the left
or right of the display, the segment of the personal
comfort settings bar lights up to indicate the
selected setting. To select a lower or higher setting,
press the button on the left or right of the display.
10 English

Cleaning reminder
Clean the shaver after every use for optimal
performance (see 'Cleaning and maintenance').
When you switch off the shaver, the cleaning
reminder flashes to remind you to clean the
shaver.
Travel lock
3 sec.
When you are going to travel, you can lock the
shaver to prevent it from accidentally switching on
(see 'Activating the travel lock').
Replacement reminder
For maximum shaving performance, replace the
shaving heads every two years. The shaver is
equipped with a replacement reminder which
reminds you to replace the shaving heads. The
shaver beeps, the replacement reminder lights up
and the arrows flash to indicate that you have to
replace the shaving heads.
Note: After replacing the shaving heads, you can
reset the replacement reminder by pressing the
on/off button for 7 seconds. If you do not reset the
replacement reminder, the shaver resets
automatically after 9 shaves.
’Unplug for use’ reminder
11
English

The ‘unplug for use’ symbol flashes to remind you
to disconnect the shaver from the wall socket
before you can switch it on.
Notification symbol
Overheating
If the shaver overheats during charging, the
notification symbol flashes. When this happens,
the shaver automatically stops charging. Charging
continues once the temperature of the shaver has
decreased to the normal level after approx. 10
minutes.
Blocked shaving heads
If the shaving heads are blocked, the notification
symbol continuously lights up red. The
replacement reminder and the cleaning reminder
alternately flash white and the shaver beeps. In
this case, the motor cannot run because the
shaving heads are dirty or damaged. If the shaving
heads are dirty, you have to clean them. If the
shaving heads are damaged, you have to replace
them.
Charging
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 1 hour. A fully charged
shaver has a shaving timeof up to 60 minutes.
Note: You cannot use the shaver while it is
charging.
12 English

Quick charge
After approx. 5 minutes of charging the shaver
contains enough power for one shave.
Charging with the supply unit
1Make sure the shaver is switched off.
2Put the small plug in the shaver and put the
supply unit in the wall socket.
The display of the shaver indicates that the
shaver is charging.
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
shaver.
Note: When the battery is full, the display
switches off automatically after 15 minutes.
Using the shaver
Always check the shaver and all accessories
before use. Do not use the shaver or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with one of
the original type.
This symbol indicates that the shaver can be used
in the bath or shower.
- Use this shaver for its intended household use
as described in this manual.
- For hygienic reasons, the shaver should only be
used by one person.
- Trimming is easier when the skin and hair are
dry.
Note: This shaver is waterproof. It is suitable for
use in the bath or shower and for cleaning under
the tap. For safety reasons, the shaver can only be
used without cord.
13
English

Switching the shaver on and off
1To switch on the shaver, press the on/off
button once.
The battery charge percentage lights up for a
few seconds.
2To switch off the shaver, press the on/off
button once.
The battery charge percentage lights up for a
few seconds and shows the remaining battery
charge.
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3
weeks.
Shaving tips
- For the best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days or
longer.
- Select your personal comfort setting (see
'Personal comfort settings').
Dry shaving
1Switch on the shaver.
14 English

2Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
3Switch off and clean the shaver after each use
(see 'Cleaning and maintenance').
The display lights up for a few seconds to show
the remaining battery charge.
Wet shaving
For a more comfortable shave, you can also use
this appliance on a wet face with shaving foam or
shaving gel.
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your skin.
3Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4Switch on the shaver.
15
English

5Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Make sure each shaving
head is fully in contact with the skin. Exert
gentle pressure for a close, comfortable shave.
Note: Do not press too hard, as this can cause
skin irritation.
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6Dry your face.
7Switch off the shaver and clean it after each
use.
Note: Make sure that you rinse all foam or shaving
gel off the shaver.
Using click-on attachments
Removing or attaching click-on attachments
1Make sure the shaver is switched off.
2Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off the shaver.
3Insert the lug of the attachment into the slot in
the top of the shaver. Then press down the
attachment to attach it to the shaver (‘click’).
Using the precision trimmer attachment
You can use the precision trimmer attachment to
touch up your beard, sideburns and moustache.
16 English

1Attach the attachment to the appliance (‘click’).
2Switch on the appliance.
3Hold the precision trimmer perpendicular to the
skin and move it downwards while exerting
gentle pressure.
4Switch off the appliance and clean the
attachment after use (see 'Deactivating the
travel lock').
Travel lock
You can lock the shaver when you are going to
travel to prevent it from switching on accidentally.
Activating the travel lock
1Press the on/off button for 3 seconds to use
the travel lock mode.
3 sec.
While you activate the travel lock, the travel lock
symbol lights up briefly and the shaver
produces a short sound.When the travel lock is
activated, the travel lock symbol flashes.
If you try to switch on the shaver while the
travel lock is active, the travel lock symbol
flashes.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
While you deactivate the travel lock, the travel
lock symbol lights up briefly and the shaver
produces a short sound. The shaver switches on
and is now ready for use again.
Note: The shaver unlocks automatically when it is
connected to the wall socket.
17
English

Cleaning and maintenance
Regular cleaning guarantees better shaving
results.
Never clean, remove or replace the shaving
unit while the shaver is switched on.
Do not apply pressure to shaving head guards.
Do not touch shaving heads with hard objects
as this may dent or damage the precision-
made slotted guards.
Do not use compressed air, abrasives, scourers
or aggressive liquids such as petrol or acetone
to clean the shaver.
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
performance.
Always check if the water is too hot, to prevent
burning your hands.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
While rinsing the shaving unit, water may drip out
of the bottom of the shaver. This is a normal
occurrence.
1Switch on the shaver.
2Rinse the shaving unit under a warm tap.
You can also use the cleaning brush to remove
excess hairs before rinsing.
18 English

3Switch off the shaver. Pull the shaving head
holder off the bottom part of the shaving unit.
4Rinse the hair chamber and shaving head
holder under the tap.
You can also use the cleaning brush to remove
excess hairs before rinsing.
While rinsing the shaving unit, water may drip
out of the bottom of the shaver. This is a normal
occurrence.
5Carefully shake off excess water and let the
shaving head holder air-dry completely.
6Attach the shaving head holder to the bottom
part of the shaving unit (‘click’).
Thorough cleaning
We advise you to clean the shaving heads
thoroughly once a month or when the shaver does
not shave as well as it used to.
1Switch off the shaver.
19
English

2Pull the shaving head holder off the bottom
part of the shaving unit.
3Rinse the hair chamber and shaving head
holder under the tap.
You can also use the cleaning brush to remove
excess hairs before rinsing.
2
1
4Turn the retaining ring counterclockwise and lift
it off the shaving head.
Repeat this process for the other retaining rings.
Place them aside in a safe place.
5Remove the shaving heads from the shaving
head holder. Each shaving head consists of a
cutter and guard.
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally put a cutter in the wrong
shaving guard, it may take several weeks before
optimal shaving performance is restored.
6Clean the cutter and guard under the tap.
You can also use the cleaning brush to remove
excess hairs before rinsing.
7Shake off excess water.
8Put the cutter back into the guard.
20 English