Philips SW175 User manual

© & ™ Lucaslm Ltd.
© Disney
SW175

3
2
1
7
8
9
10
12
13
14
11
4
6
5

empty page before TOC

English 6
Français (Canada) 22

English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the features of this shaver as
well as some tips to make shaving easier and more
enjoyable.
General description (Fig. 1)
1 Comb for beard styler attachment
2 Click-on beard styler attachment
3 Protection cap
4 Shaving unit with shaving head holder
5 Shaving head holder release button
6 On/off button
7 Retaining ring
8 Cutter
9 Guard
10 Shaving head holder
11 Supply unit
12 Charging light
13 Small plug
14 Socket for small plug
Important safety information
Read this important information carefully before
you use the appliance and its accessories and save
it for future reference. The accessories supplied
may vary for different products.
6English

Danger
- Keep the supply unit dry.
Warning
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the
appliance.
- The supply unit contains a transformer. Do not
cut off the supply unit to replace it with another
plug, as this causes a hazardous situation.
- Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
- Always unplug the shaver before you clean it
under the tap.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Never immerse the cleaning system or the
charging stand in water and do not rinse it
under the tap.
- Never use water hotter than 60°C to rinse the
shaver.
- Only use this appliance for its intended purpose
as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
7
English

- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
- If your shaver comes with a cleaning system,
always use the original Philips cleaning fluid
(cartridge or bottle, depending on the type of
cleaning system).
- Always place the cleaning system on a stable,
level and horizontal surface to prevent leakage.
- If your cleaning system uses a cleaning
cartridge, always make sure the cartridge
compartment is closed before you use the
cleaning system to clean or charge the shaver.
- When the cleaning system is ready for use, do
not move it to prevent leakage of cleaning fluid.
- Water may drip from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the
shaver.
- Do not use the supply unit in or near wall
sockets that contain an electric air freshener to
prevent irreparable damage to the supply unit.
Electromagnetic fields (EMF)
- This Philips appliance complies with all
applicable standards and regulations regarding
exposure to electromagnetic fields.
General
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the
tap. For safety reasons, the shaver can
therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
8English

- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
Charging
Charge the shaver before you use it for the first
time and when the appliance starts to work more
slowly.
Note: First time charging or charging after a long
period of non-use requires 90 minutes of charge
time.
Charging takes approx. 10 hours. A fully charged
shaver has a shaving time of up to 40 minutes.
Note: You cannot use the shaver while it is
charging.
Note: Depending on your shaving/styling behavior
and beard type, the operating time may vary over
time.
Charging with the supply unit
1Make sure the shaver is switched off.
2Put the small plug in the shaver and put the
supply unit in the wall socket.
The light on the supply unit lights up to show
that the shaver is charging.
Note: The light on the supply unit does not
change color and does not go out when the
shaver is fully charged..
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
shaver.
Using the shaver
Always check the shaver and all accessories
before using. Do not use the shaver or any
accessory if it is damaged, as this may cause
9
English

injury. Always replace a damaged part with one of
the original type.
This symbol indicates that the shaver can be used
in the bath or shower.
- Use this shaver for its intended household use
as described in this manual.
- For hygienic reasons, the shaver should only be
used by one person.
- Trimming is easier when the skin and hair are
dry.
Note: This shaver can only be used without a cord.
Switching the shaver on and off
1Press the on/off button once to switch the
shaver on or off.
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week) and
exclusively with this appliance for a period of 3
weeks.
For the best results on skin comfort, pre-trim your
beard if you have not shaved for 3 days or longer.
Dry shaving
1Switch the shaver on.
10 English

2Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
3Switch off the shaver and clean it after each
use.
4Put the protection cap on the shaver to protect
shaver heads.
Wet shaving
For a more comfortable shave, you can also use
this shaver on a wet face with shaving foam or
shaving gel.
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your skin.
3Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4Switch the shaver on.
5Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Exert gentle pressure for a
close, comfortable shave.
11
English

Note: Do not press too hard, this can cause skin
irritation.
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6Dry your face.
7Switch off the shaver and clean it after each
use.
Note: Make sure that you rinse all foam or shaving
gel off the shaver.
Using the click-on attachments
Removing or attaching the click-on
attachment
1Make sure the shaver is switched off.
2Pull the attachment straight off the shaver.
Note: Do not twist the attachment while you
pull it off.
3Insert the lug of the attachment into the slot in
the top of the shaver. Then press down the
attachment to attach it to the shaver(‘click’).
Using the beard styler attachment with
comb
You can use the beard styler with the comb
attached to style your beard at one fixed setting,
but also at different length settings. You can also
use it to pre-trim any long hairs before shaving for
a more comfortable shave.
The length settings on the beard styler attachment
correspond to the remaining hair length after
cutting and range from 1 to 5mm (3/64 - 3/16in).
12 English

1Attach the beard styler to the shaver ('click').
2Slide the comb straight into the guiding grooves
on both sides of the beard styler (‘click’).
Note: Hold the comb in the center to attach it to
the beard styler. Do not push at the sides of the
comb.
2
1
3Press the length selector and then push it to
the left or right to select the desired hair length
setting.
4Switch on the shaver.
5Move the product upwards while you exert
gentle pressure. Make sure the front of the
comb is in full contact with the skin.
6Clean the beard styler after use.
Using the beard styler attachment without
comb
You can use the beard styler attachment without
the comb to contour your beard, moustache,
sideburns or neckline to a length of 0.5mm (1/32
in).
1Pull the comb off the beard styler.
Note: Grab the comb in the center to pull it off
the beard styler. Do not pull at the sides of the
comb.
2Switch on the shaver.
13
English

3Hold the beard styler perpendicular to the skin
and move the product downwards while you
exert gentle pressure.
4Clean the beard styler after use.
Cleaning and maintenance
- Regular cleaning guarantees better shaving
results.
- Never clean, remove or replace the shaving unit
while the shaver is switched on.
- Do not apply pressure to shaving head combs.
- Do not touch shaving heads with hard objects
as this may dent or damage the precision-made
slotted combs.
- Do not use abrasives, scourers or aggressive
liquids such as gasoline or acetone to clean the
shaver.
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
performance.
Always check if the water is too hot, to prevent
burning your hands.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
While rinsing the shaving unit, water may drip out
of the base of shaver. This is a normal occurrence.
1Switch the shaver off, unplug from outlet and
remove power cord from the shaver.
14 English

2Rinse the shaving unit under a warm tap for
some time.
3After rinsing the shaver under the tap, hold it
upright for 10-15 seconds to allow water to run
out of the bottom.
1
12
4Press the release buttons on the shaving unit
and pull the shaving head holder off the
shaving unit.
5Rinse the shaving head holder and hair
chamber under a warm tap for 30 seconds.
6Carefully shake off excess water and let the
shaving head holder air dry completely.
7Reattach the shaving head holder to the
shaving unit (‘click’).
Cleaning the beard styler attachment
Clean the beard styler after each use.
1Pull the comb off the beard styler.
Note: Grab the comb in the center to pull it off
the beard styler. Do not pull at the sides of the
comb.
2Switch on the shaver.
15
English

3Rinse the beard styler and the comb separately
under a warm tap.
4After cleaning, switch off the shaver.
5Carefully shake off excess water and let the
beard styler and comb air dry completely.
Never dry the trimmer with a towel or tissue,
as this may damage the trimming teeth.
6For optimal performance, lubricate the teeth of
the attachment with a drop of sewing machine
oil regularly.
Replacement
Replacing the shaving heads
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
Replace damaged shaving heads immediately.
Always replace the shaving heads with original
Philips shaving heads
1Switch off the shaver and disconnect it from the
wall socket.
1
12
2Press the release buttons on the shaving unit
and pull the shaving head holder off the
shaving unit.
3To unlock the retaining ring, turn it in the
direction of the arrows indicated in and on the
retaining ring.
16 English

2
1
4Lift the retaining ring out of the shaving head
holder. Place aside in a safe place.
1
2
5Remove the shaving heads and place new ones
in the shaving head holder.
Discard the used shaving heads immediately to
avoid mixing them with the new shaving heads.
Make sure the two wings of the new shaving
heads fit exactly into the recesses of the
shaving head.
1
2
6Place the retaining ring back onto the shaving
head holder. To reattach the retaining ring, turn
it against the direction of the arrows indicated
in and on the retaining ring.
Make sure the retaining ring is fixed properly.
The four wings of the retaining ring have to be
located exactly under the recesses of the
shaving head holder.
7Reattach the shaving head holder to the
shaving unit (‘click’).
If the shaving unit does not close smoothly,
check if you have positioned the shaving heads
properly and if the retaining rings are fixed
properly.
Storage
Put the protection cap on the shaver to prevent
damage.
Note: Always let the shaver air dry completely
before storing.
17
English

Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the
international warranty leaflet for contact details).
The following accessories are available:
- SH30 Philips shaving heads
Disposal
- This product contains a rechargeable NiMH
battery which must be disposed of properly.
- Contact your local town or city officials for
battery disposal information. You can also call
888-224-9764 or visit www.call2recycle.ca for
battery drop-off locations.
- For assistance, visit our website
www.philips.com/support or call
1-800-243-3050 toll free.
- Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused. For recycling
information, please contact your local waste
management facilities or visit
www.recycle.philips.com.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when
you discard the shaver. Before you remove
the battery, make sure that the shaver is
disconnected from the wall socket and that
the battery is completely empty.
Take any necessary safety precautions
when you handle tools to open the shaver
18 English

and when you dispose of the rechargeable
battery.
1Undo the screw in the back panel of the shaver
with a screwdriver and remove the back panel.
2Bend the hooks aside and remove the power
unit.
3Break the snap hooks and remove the front
panel of the power unit.
4Take out the battery holder and cut the battery
tags with a pair of cutting pliers.
5Remove the rechargeable battery.
Warranty and support
If you need information or support, please
www.philips.com/support or call toll free:
1-866-800-9311. To locate the nearest Philips
warranty depot, visit our website www.philips.com.
Guarantee restrictions
- Philips Consumer Lifestyle warrants its products
for a period of two years after the date of
purchase. If any defect due to faulty materials
and workmanship occurs within this two-year
warranty period, Philips Consumer Lifestyle will
repair or replace the product at its expense.
- Philips Consumer Lifestyle will only pay for
repair or replacement if convincing proof is
provided, for instance by means of a receipt,
that the day on which service is claimed is
within the guarantee period. Parts that are
subject to wear (such as cutting units and
shaving heads) are not covered by the terms of
the international guarantee.
19
English

- The guarantee is not valid if a defect is due to
damage caused by incorrect use, poor
maintenance (e.g. parts blocked by scale) or if
alterations or repairs have been carried out by
persons not authorized by Philips Consumer
Lifestyle.
- For the appliance to be used correctly, the user
should strictly adhere to all instructions
included in the user manual and should abstain
from any actions or uses that are described as
undesired or which are warned against in the
user manual.
- These warranty restrictions do not affect your
statutory rights.
Troubleshooting
Shaver
Problem Possible cause Solution
The appliance
does not work
when I press the
on/off button.
The appliance is still
attached to the wall
socket. For safety
reasons, the
appliance can only
be used without
cord.
Unplug the appliance and
press the on/off button to
switch on the appliance.
The rechargeable
battery is empty. Recharge the battery.
The travel lock is
activated. Press the on/off button for 3 seconds to deactivate the
travel lock.
The shaving unit is
soiled or damaged
to such an extent
that the motor
cannot run.
Clean the shaving heads
thoroughly or replace them.
Also see 'Hairs or dirt
obstruct the shaving heads'
for a detailed description of
how to clean the shaving
heads thoroughly.
20 English