Philips MCW770/22B Operating manual

1
English
Quick Use Guide MC W770
Open the battery compartment of the remote control and insert
2 alkaline batteries, type AA (R06, UM-3).
1Connect the speaker cables to the MC W770.
Use the supplied speakers only. Using other speakers
can damage the set or the sound quality will be
negatively affected.
2Connect the AM/MW antenna.
3Connect the FM antenna.
4If you want to connect an additional appliance, use a cinch
cable to connect the audio inputs of the MC W770 to the
audio outputs of the additional appliance.
5Check whether the mains voltage as shown on
the type plate corresponds to your local mains
voltage. If it does not, consult your dealer or
service organisation.
Make sure all connections have been made
before switching on the mains supply.
Connect the AC power cord supplied to
AC MAINS ~ and to the wall socket.
Supplied accessories
1Insert batteries
2Connect speakers, antennas, an additional appliance (optional)
and the AC power cord
– PC link software installer CD-ROM
– Wireless USB adapter and extension cable
– Remote control and 2 batteries, size AA
–2loudspeaker boxes including
2 speaker cables
– AM/MW loop antenna
–FM wire antenna
–AC power cord
This Quick Use Guide gives a rough
overview and helps to start quickly with
basic steps. Please read the supplied
instruction manual for detailed
information.
MC-W770 QUG/22.1 eng 8/23/01 10:45 Page 1

2
3Install the tuner
1When the AC power cord is connected for the first time
to the wall socket, TUNER and AUTO INSTALL - PRESS
PLAY are displayed.
2Press ÉÅ on the set to store all available radio stations
automatically.
➜Automatic searching and storing starts. Once completed,
the last tuned radio station will be played.
4Play your discs on the set
For playback on this set you can use:
– All pre-recorded audio CDs
– All finalised audio CDR and CDRW discs
– MP3-CDs (CD-ROMs with MP3 tracks)
AUX PC LINKTUNERCD
CD2CD3
CD5
CD4
CD1
VOL
AUX PC LINKTUNERCD
CD2CD3
CD5
CD4
CD1
ALBUM
BROWSE
VOL
SHUFFLEPROGRAMREPEAT DISPLAY
TIMERCLOCKSLEEP TIMER ON/OFF
1Press OPEN/CLOSE /on the set.
2Press one of the disc keys (DISC 1,
DISC 2, DISC 3, DISC 4, or DISC 5)
on the set to select the desired disc
tray to be opened.
3Load a disc with the printed side up. 4Press OPEN/CLOSE /again on the
set to close the tray.
5If you want to play one
particular disc:
Press one of the disc keys CD 1,
CD 2, CD 3, CD 4, or CD 5 on the
remote control to start playback of
the desired disc in the selected tray.
If you want to play all loaded
discs:
Press CD on the remote control.
Then press ÉÅ to start playback.
00To stop playback press STOP Ç.
MC-W770 QUG/22.1 eng 8/23/01 10:45 Page 2

3
1Add your MP3 music folders and files to the Philips Media Manager, during or after
installation of Philips Media Manager. Only those folders and files you can see in the
Philips Media Manager will be accessible from the MC W770.
2Make sure your PC is switched on.
3Press PC LINK Ato select the PC as source.
4As soon as the connection is established:
➜PC LINK is displayed and a track name is scrolled.
5Press ÉÅ to start playback.
➜PC LINK is displayed and the track name is scrolled.
➜PC LINK and the elapsed playing time are displayed.
PC system requirements:
– Windows 98SE/ME/2000/XP
–Pentium Class 350MHz processor or higher
– 128MB RAM or higher
– CD-ROM drive
– USB port
–Free hard disk space: 100 MB for the software
5Install the wireless connection to your PC
AUX PC LINKTUNERCD
CD2CD3
CD5
CD4
CD1
VOL
computer
AUX PC LINKTUNERCD
CD2CD3
CD5
CD4
CD1
VOL
ALBUM
BROWSE
VOL
+
supplied wireless
USB adapter
1Place the set as close as possible to the PC.
2Switch on your PC and insert the installation disc.
Note: Do not use the icon, which will appear on the PC screen during the
installation process.
3The installation guide will appear automatically. If it does not, go to the CD-ROM
drive in Windows Explorer and double click on the SETUP_.exe.Then continue
as follows:
– Select your desired language from the list.
– Select Installing Software and then select Quick Installation and click
Install.
– Then follow the installation steps prompted by the screen to install the wireless
USB adapter driver, the Philips Media Manager software and the network setup.
Note: Windows may display a warning that the driver is not approved by
Microsoft (message differs with Windows version). Ignore the message and
continue with the installation.
4Switch on the set and press PC LINK A.
5During the network setup you will be asked to go to the install mode: Press and
hold PC LINK Afor 5 seconds.
➜PC LINK is displayed and INSTALLING is scrolled.The set searches for a
connection to the PC.
When the installation has been finished successfully:
➜PC LINK and COMPLETED are displayed.
6Play your music collection from the PC via the set
Do not connect the wireless USB adapter immediately! You will be asked during
the installation process to connect it.
If you have a Firewall installed on your PC, please switch it off during the
installation.
Please close all internet connections and other programs running on your PC
before starting installation.
MC-W770 QUG/22.1 eng 8/23/01 10:45 Page 3

4 3103 305 2021.2 PDCC-LC/JW-0435
7Setting the clock
8Timer setting
1Press and hold CLOCK on the
remote control for more than
2 seconds.
➜SET CLOCK is displayed, the
hours and minutes digits start
blinking.
2Press ALBUM 5or ALBUM ∞ on
the remote control repeatedly to set
the hour.
3Press 4or ¢on the remote
control repeatedly to set the
minutes.
4Press CLOCK on the remote control
to confirm the setting.
➜The clock shows the set time.
1Press and hold TIMER on the remote
control for more than 2 seconds.
➜Xstarts blinking, SET TIMER is
displayed and the hours and
minutes digits start blinking.
2Press CD,TUNER or PC LINK Aon
the remote control to select the
source you want to be woken up
with.
3Press ALBUM 5or ALBUM ∞ on
the remote control repeatedly to set
the hour.
4Press 4or ¢on the remote
control repeatedly to set the
minutes.
5Press TIMER on the remote control
to confirm the setting.
PROGRAMREPEAT
CLOCKSLEEP
CD5
CD4
ALBUM
BROWSE
VOL
PROGRAMREPEAT
CLOCKSLEEP
●To activate the demonstration
mode press and hold
STOP DEMO Çfor 5 seconds
during standby or Eco Power standby
on the set until DEMO ON is displayed.
●To deactivate the
demonstration mode press and
hold STOP DEMO Çagain on the
set for 5 seconds until DEMO OFF is
displayed.
9Demonstration mode
TIMER
DSC VEC
TIMER ON/OFF
AUX PC LINKTUNERCD
CD2CD3
CD5
CD4
CD1
VOL
SHUFFLEPROGRAMREPEAT DISPLAY
TIMERCLOCKSLEEP TIMER ON/OFF
ALBUM
BROWSE


H
MC-W770 QUG/22.1 eng 8/23/01 10:45 Page 4