Philips 107E63 User manual

P hilips _ma nual_
Tues day, November 18, 2003 3:00:45 P M
107E63 / 107E69

BZ02
41A 774813 1A6275
FABRICADO POR C.N.P.J. 04.176.689/0001-60

1
Before operating the monitor please read this manual thoroughly. This
manual should be retained for future reference.
Contents
Packing list ---------------------------------------------------- 1
Precautions ---------------------------------------------------- 2
Installation Instructions ------------------------------------- 3
Swivel Base -------------------------------------------------- 3
Power cord -------------------------------------------------- 3
Video cable -------------------------------------------------- 4
Operating Instructions -------------------------------------- 5
General Instructions -------------------------------------- 5
Front panel control ---------------------------------------- 6
How to adjust a setting ----------------------------------- 6
Adjusting the picture ------------------------------------- 7-8
Plug and play -------------------------------------------------- 9
Technical Support (FAQ) ----------------------------------- 10
Appendix A – Specifications ------------------------------- 11-12
Appendix B – Factory Preset Timing Table ------------ 13
Your International Guarantee -----------------------------
14
PACKING LIST
The product package should include the following items:
1. Monitor
2. Owner's Manual
3. Power Cord
4. Swivel Base

2
PRECAUTIONS
zDo not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
zDo not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit
instructions.
zSlots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
zThe monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
zThe monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power
outlet as a safety feature. If your outlet does not accommodate the three-
wire plug, have an electrician install the correct outlet, or use an adapter
to ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
zUnplug the unit during a lightning storm or when it will not be used for
long periods of time. This will protect the monitor from damage due to
power surges.
zDo not overload power strips and extension cords. Overloading can result
in fire or electric shock.
zNever push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
zDo not attempt to service the monitor yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
zTo ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240 VAC, Min. 2.5A.
zThe wall socket shall be installed near the equipment and shall be easily
accessible.

3
INSTALLATION INSTRUCTIONS
Swivel Base
To attach the swivel base to the monitor, do the following:
•Carefully turn the monitor on its side or upside down. ( see figure 1 )
•Locate the cavities at the bottom front of the monitor.
•Insert the pegs on the swivel base into these cavities. Push the swivel base
forward until the swivel base locks in place.
•To remove the swivel base, hold the bottom of the swivel base, then push
it out.
Install Remove
Figure 1 Installing and Removing the Swivel Base
Power Cord
Power Source:
1. Make sure the power cord is the correct type that required in your area.
2. This monitor has a universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area ( No user adjustment is
required. )
3. Connect the power cord into your monitor’s power input socket, and then
plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your
monitor.

4
Video cable
Connecting the Video Cable: The monitor comes with a built-in video cable.
Plug the signal cable's 15-pin connector into the computer's video port and
tighten the two screws on the cable connector.
Caution:Don’t bend the signal cable, otherwise it will break the inner wire.
Connecting the Power Cord: Plug the power cord into the monitor's AC
power socket. Then plug the power cord into a grounded AC outlet or UL-
approved power strip or the power output socket on your PC.
Caution: If the AC outlet is not grounded (with three holes), install the
proper grounding adapter (not supplied).
Figure 2 Connecting Cables
1. Power Cord 2. Signal Cable

5
OPERATING INSTRUCTIONS
General Instructions
The power switch is located at front panel of the monitor. Press the power
switch to turn the monitor on or off. The other control knobs are located at
the base of the monitor (See Figure 3). By changing these settings, the
picture can be adjusted to your personal preferences.
•The power cord should be connected.
•Connect the video cable from the monitor to the video card.
•To turn the monitor on, press the POWER switch to ON position. The
power indicator will light up.
•Your monitor features a unique quick switch system which provides a
picture within seconds after the monitor is switched on.
Figure 3 External Control Knob
1. POWER SWITCH 4. CONTRAST/
2. POWER INDICATOR 5. BRIGHTNESS/
3. MENU 6. EXIT
Notes
•Do not install the monitor in a location near heat sources such as
radiators or air ducts , or in a place subject to direct sunlight , or
excessive dust or mechanical vibration or shock.
•Save the original shipping carton and packing materials, as they will
come in handy if you ever have to ship your monitor.
•For maximum protection, repackage your monitor as it was originally
packed at the factory.
•To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a
mild detergent solution. Never use strong solvents such as thinner,
benzene, or abrasive cleaners, since these will damage the cabinet. As a
safety precaution, always unplug the monitor before cleaning it.
1
2
3
1
2
3
6
5
4

6
Front Panel Control
•Power Switch: Press thisknob to switch ON/OFF the monitor’s power.
•MENU:Active OSD menu or function adjust confirm.
•Contrast/ :Adjust contrast or function adjust.
•Brightness / :Adjust brightness or function adjust.
•EXIT: Press the EXIT key to disable OSD menu.
•Power Indicator:
Green — Power On mode.
Orange — Off mode.
How to adjust a setting
The monitor controls are accessed by pressing button MENU to enable OSD
(On-Screen-Display). The main menu will be displayed as follows.
1024 X 768
Figure 4 The OSD Message
Note: If adjustment or selection of any OSD menu is not made for more
than 10 seconds, the current setup will be saved and the OSD will disappear
automatically.

7
Adjusting the picture
The description for functional control icons
1. CONTRAST :
Adjust the picture contrast.
2. BRIGHTNESS :
Adjust the picture brightness.
3. H-CENTER :
Adjust the horizontal position of the picture.
4. H-SIZE
:
Adjust the picture’s horizontal size.
5. V-CENTER :
Adjust the vertical position of the picture.
6. V-SIZE :
Adjust the picture’s vertical size.
7. ZOOM :
Adjust the picture’s horizontal and vertical size simultaneously.
8. PINCUSHION :
Adjust the pincushion and barrel.
9. TRAPEZOID
:
Adjust the picture’s trapezoid distortion.
10. PIN-BALANCE
:
Adjust to compensate the pincushion unbalance.
11. PARALLELOGRAM :
Adjust the picture to be a rectangle.
12. ROTATION :
Adjust the picture tilt to horizontal position.
13. 6500°K/9300°K ( COLOR TEMPERATURE ) :
The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K
is x=0.283, y=0.297. It presents two different color sets on the screen.
You can select 9300°K or 6500°K by pressing MENU Key.

8
14. USER COLOR ( Red / Blue ) :
If the 9300°K normal white or 6500°K warmer white do not satisfy
your desire, properly adjust R . B GAIN controls to obtain your
optimum whiteness level.
15. DEGAUSS :
If color impurity occurs when moving or swiveling the monitor,
press MENU Key and degauss to fix the picture condition.
16. MOIRE REDUCE :
Moire is the result of interference between the phosphor layout and
the video signal. In some cases, you may find the moire very
noticeable. Press the MENU to enter in the moire reduce setting.
Please adjust the level to the optimum condition. Note: Too high of a
setting will cause the picture to shake.
17. RECALL :
Press RECALL to restore the monitor to factory settings.
18. EXIT :
Close OSD window.
19. SELECT LANGUAGE
:
Select the language as you like.

9
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS
MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO
INPUT SIGNAL.
This monitor meets the Power Management standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees ( NUTEK ). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's
internal power supply consumption. After the video input signal is restored,
full power is restored and the display is automatically redrawn. The
appearance is similar to a "Screen Saver" feature except the display is
completely off. The display is restored by pressing a key on the keyboard, or
clicking the mouse.
Plug and play
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, communicate
additional information about its display capabilities. The communication
channel is defined in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data
channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.
Video Cable Pin Assignments:
1. Red 5. Ground 9. NC 13. H-sync
2. Green 6. R-Ground 10. Ground 14. V- sync / * VCLK
3. Blue 7. G-Ground 11. NC 15. DDC-SerialClock
4. NC 8. B-Ground 12. DDC-SerialData* FOR DDC

10
TECHNICAL SUPPORT (FAQ)
Problem & Question Possible Solution
Power LED is not on *Check if the Power Switch is in the ON
position
*Power Cord should be connected
No Plug & Play *Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Make sure the Monitor Drivers are
installed
Picture is fuzzy *Adjust the Contrast and Brightness
Controls.
Picture bounces or a wave
pattern is present in the
picture
*Move electrical devices that may cause
electrical interference.
The power LED is ON
(orange) but there’s
no video or no picture
*Computer Power Switch should be in the
ON position
*Computer Video Card should be snugly
seated in its slot
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and
make sure that none of the pins are bent.

11
APPENDIX A - SPECIFICATIONS
CRT(Picture Tube) 43,2cm (17"), 90º deflection, 29mmneck,
0.27mm dot pitch glare screen.
Visible Image Size 40,6 (16"), diagonal
Display Color
•Analog input Unlimited colors
Input Signal All timing that meets scanning frequencies
Specification
•Video •Analog R, G, B 0.7Vpp positive/75 ohm
•Sync. •Horizontal sync. : Positive/Negative
•Vertical sync. : Positive/Negative
Synchronization
•Horizontal 30kHz to 72kHz automatically
•Vertical 50Hz to 160Hz automatically
Max. Resolution 1280×1024
Video bandwidth 110MHz
Factory Preset Timings : 7
User mode Timings : 12
Misconvergence
•Center 0.3mm Max.
•Corner 0.4mm Max.
Power Source Switching mode power supply
AC 100-240V, 50Hz/60Hz full range
Operating 0°C to 40°C ambient
Humidity 10% to 85% relative, non-condensing
Weight 15.5kg(Net)
Dimensions
•Monitor 410(W) × 402(H) × 420(D)mm
Signal Cable 15 pin mini D-Sub
External Controls:
Switch •POWER SWITCH
•MENU KEY
•CONTRAST/UP KEY
•BRIGHTNESS/DOWNKEY
•EXIT KEY

12
Functions ( OSD ) •CONTRAST
•BRIGHTNESS
•H-CENTER
•H-SIZE
•V-CENTER
•V-SIZE
•ZOOM
•PINCUSHION
•TRAPEZOID
•PIN-BALANCE
•PARALLELOGRAM
•ROTATION
•6500°K
•USER COLOR
•9300°K
•DEGAUSS
•MOIRE REDUCE
•RECALL
•EXIT
•SELECT LANGUAGE
Plug & Play DDC1/2B
On mode ≤75W EPA ENERGY
STAR®Off mode
≤2W
Power consumption 75W Max.
Preset display area 310mm × 230mm
Regulations UL, CSA, FCC, CE

13
APPENDIX B – FACTORY PRESET TIMING TABLE
STANDARD RESOLUTION
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
IBM 720 × 400 31.5kHz 70Hz
VGA 640 × 480 31.5kHz 60Hz
VESA/85 640 × 480 43.3kHz 85Hz
VESA/85 800 × 600 53.7kHz 85Hz
VESA/85 1024 × 768 68.7kHz 85Hz
VESA/60 1280 × 1024 64.0kHz 60Hz
VESA/75 1152 × 864 67.5kHz 75Hz

文保修卡 14
YourInternationalGuarantee
DearCustomer,
Thank youforpurchasingthisPhilipsproductwhichhasbeendesignedand
manufacturedtothe highestqualitystandards.
If,unfortunately,somethingshouldgowrongwiththisproduct Philips
guaranteesfree of chargelaborandreplacementpartsirrespectiveofthe
countrywhereitisrepairedduringaperiodof 12 monthsfromdateof
purchase.ThisinternationalPhilipsguarantee complementstheexisting
nationalguarantee obligationstoyouofdealersandPhilipsinthecountryof
purchaseanddoesnotaffectyourstatutoryrightsasacustomer.
ThePhilipsguarantee appliesprovidedtheproduct ishandledproperlyforits
intendeduse, inaccordance withitsoperatinginstructionsandupon
presentationof theoriginalinvoice orcashreceipt,indicating thedateof
purchase, dealer's nameandmodel andproductionnumberof the product.
ThePhilipsguarantee maynotapplyif:
•thedocumentshavebeenalteredinanywayormadeillegible;
•themodelorproductionnumberontheproducthasbeenaltered,
deleted,removedormadeillegible;
•repairsorproductmodificationsand alterationshavebeenexecuted
byunauthorizedservice organizationsorpersons;
•damageiscausedbyaccidentsincludingbut not limitedtolightning,
waterorfire,misuseorneglect.
Pleasenotethattheproductisnotdefectiveunderthisguarantee inthecase
wheremodificationsbecomenecessaryinorderfortheproducttocomply
withlocal ornationaltechnicalstandardswhichapplyincountriesforwhich
theproductwasnotoriginallydesignedand/ormanufactured.Therefore
alwayscheckwhetheraproduct canbeusedinaspecificcountry.
In caseyourPhilipsproductisnotworkingcorrectlyorisdefective,please
contactyourPhilipsdealer. Intheeventyourequireservice whilst inanother
countryadealeraddresscanbegiventoyoubythePhilipsConsumerHelp
Deskinthat country,thetelephoneandfaxnumberof whichcanbefoundin
the relevantpartof thisbooklet.
In ordertoavoidunnecessaryinconvenience,weadviseyoutoreadthe
operatinginstructionscarefullybeforecontactingyourdealer.Ifyouhave
questionswhichyourdealercannotansweroranyrelatedquestionplease
contactthePhilipsConsumerInformationCenters orvia:
Website: http://www.philips.com

1
Antesdeoperarelmonitorporfavorlee estemanual completamente.Se
deberetenerestemanual para futura consulta.
ndice
Listadelpaquete ----------------------------------------------
1
Precauciones---------------------------------------------------
2
Instruccionesde instalación---------------------------------
3
BaseGiratoria ----------------------------------------------
3
Cordónde corriente ---------------------------------------
3
Cablede video ---------------------------------------------
4
Instruccionesoperativas --------------------------------------
5
Instruccionesgenerales-----------------------------------
5
Mando deltablerode frente-----------------------------
6
Comoajustarlainstalación-----------------------------
6
Ajustando de imagen -------------------------------------
7-8
Plug & Play ----------------------------------------------------
9
Soportetécnico (FAQ) ---------------------------------------
10
Apéndice A- Característicastécnicas ---------------------
11-12
Apéndice B - Tablade CoordinaciónProgramada por
Fábrica ------------------------------------------
13
Su GarantíaInternacional -----------------------------------
14
LISTADEPAQUETE
El embalaje de productodebe incluir lossiguientesarticulos:
1. Monitor
2. Manual del Propietario
3. Cord ndeCorriente
4. BaseGiratoria

2
PRECAUCIONES
lNousarelmonitorcercanoaagua, porejemplocercanodeunabañera,
palangana, fregadero, tina delavandería, piscina oens tanomojado.
lNoponerelmonitorenunacarretilla inestable,plataforma, omesa. Si
elmonitorcaer, élpuedeherirunapersonaycausardañosseriosal
aparato.Usas lamentela carretilla oplataforma recomendadaporel
fabricanteovendidoconelmonitor.Simontarelmonitorenunapared
oestante,usaunconjuntodesoporteaprobadoporelfabricanteysigue
lasinstruccionesdel conjunto.
lRañurasoaberturasenla partetrasera yinferiordela cajasonprovistos
paraventilaci n.Paraasegurarfuncionamientofiabledelmonitory
paraprotegerlodesobrecalentamiento,asegurarsequeestasaberturas
noestánbloqueadasocubiertas.Nopongaselmonitorsobrela cama,
sofá, alfombra, osuperficiesimilar.Nopongaselmonitorcercanoo
encima deunradiadororegistrodecalor.Nopongaselmonitorenun
estanteparalibrosoarmarioamenosqueseaproporcionadauna
ventilaci npropia.
lEl monitordebeseroperadosolamenteconeltipodefuentedeenergía
indicadoenla etiqueta. Sinoestássegurodeltipodeenergia
suministradoasuhogar,consulta asuvendedorocompañíadeenergía
local.
lEl monitoresequipadoconclavijatripolar,unaclavijaconuntercero
polo(tierra).Esta clavijaconectar_solamenteaunatoma decorriente
conectadaatierracomocaracterísticadeseguridad.Sisutoma de
corrientenoacomodala clavijatripolar,llameaunelectricista para
instalarla toma decorrientecorrecta, ousaunadaptadorparaconectar
el aparatoa tierra seguramente. Nodescuidardelprop sitodeseguridad
dela clavija conectada a tierra.
lDesenchufarla unidadduranteuna tormenta conrelámpagoocuandoel
monitornoesusadoporperíodoslargosdetiempo.Estoprotegeráel
monitordedañosdebidoa sobretensi ntransit ria deenergía.
lNosobrecargarflejesdeenergíasycordonesdeextensi n.Sobrecarga
puederesultarenincendioochoqueeléctrico.
lNuncaempuje cualquierobjetodentrodela rañuraenla cajadel
monitor. Élpuedecausarcortocircuitoenlaspiezasyresultarenfuego
ochoqueeléctrico. Nunca derrama líquidosenel monitor.
lNointenta repararelmonitortumismo;aberturaoquitaci ndetapas
puedeexponerteavoltajespeligrososyotroriesgos.Favordereferir
todoservicioal personal derevisi ncalificado.
lParaasegurarfuncionamientosatisfactorio,usaelmonitorsolocon
ordenadoreslistadosULquetienenreceptáculosapropiadamente
configuradosentre100- 240VAC, Min. 2.5A.
lEl soquetedeparedsedebeinstalarcerca del equipoyconfácil acceso.

3
INSTRUCCIONESDEINSTALACIÓN
BaseGiratoria
Paraatar labase giratoriaal monitor, haga el siguiente :
•Vuelvecuidadosamenteel monitorsobresuladooal revés.
(véa figura 1).
•Localiza lascavidadesa la parteinferiordelantera del monitor.
•Introduce lasclavijassobrela basegiratoria enestascavidades.Empuje
la basegiratoria hacia adelantehasta quela basegiratoria cierreenel
lugar.
•Paraquitarla basegiratoria, tenla parteinferiordela basegiratoria,
despuésempuje lofuera.
Assemblage Démontage
Figura 1InstalandoyQuitandola BaseGiratoria
Cordónde Energía
Fuentede energía:
1. Aseguratequeelcord ndeenergíaeseltipocorrectorequeridoensu
área.
2. Estemonitortieneunafuentedeenergíauniversal quepermite
funcionamientoenvoltaje 100/120Vo220/240VACdela área(Nose
requiereningúnajustedel usuario.)
3. Conecta elcord ndeenergíadentrodeunenchufedeentradade
energíadesumonitor,ydespuésconecta elotroextremoenunatoma
decorrientetripolarAC.El cord ndeenergíapuedeserconectadaa
unatoma decorrientedela paredoenchufedeenergíadelsuPC,
dependiendodel tipodecord ndeenergía suministradoconsumonitor.

4
Cablede Video
Conexióndel Cable Video: El monitorvieneconuncablevideo
incorporado.Enchufaelconectorde15 pinzasdelcabledesignoenla
ranuravideodela computadorayapretarlosdostornillosenelconectorde
cable.
Precauci n: No encorvael cable dese al,deotromodo puederomperel
alambre interior.
Conexióndel Cable deRede: Enchufa el CabledeRedeenelportadorAC
delmonitor.LuegoenchufaelcableenuntomacorrientesACcontierrao
soquetedesalida deredeensuPC.
Precauci n: Siel enchufe ACno estáconectada atierra,instalael
adaptadorpropioconectado atierra(no suministrado).
Figura 2-ConectandoCables
1. Cablederede2. Cabledesigno