Philips DB21-A User manual

NOTE : LAMP STYLE WILL VARY WITH FIXTURE OPTIONS.
HEAD
SCREWS
(3X)
HEAD
ASSEMBLY
THREADED
GLOBE
LAMP
GLOBE
GASKET
(IN RECESS)
CAUTION
WARNING : TURN POWER OFF BEFORE INSTALLING OR 1.
PERFORMING ANY MAINTENANCE ON THIS FIXTURE.
Failure to do so may result in severe injury or death.
GFI PROTECTION! Fixtures which may come in contact with or 2.
be exposed to moisture (i.e. outdoors) shall be installed on a
GFI (Ground Fault Interruptor) circuit. (120V only.)
The fixture should not be installed in low lying areas or where 3.
water may accumulate and stand for long periods of time.
INSTALLATION
WARNING : Make sure the power is off before installing or 1.
servicing this fixture.
Install the anchor rods into a concrete footing as indicated on 2.
the supplied template. Install and level the baseplate with
ballast assembly as shown on the template.
Connect the supply lines from the supply conduit to the fixture's 3.
input leads according to NEC procedures. Tie the wires so they
do not lie on the ground. HID & Fluorescent : Connect the lamp
supply quick-connect to the ballast quick-connect pigtail.
Set the fixture onto the baseplate and tighten the three 4.
mounting screws to secure the fixture. Be sure not to crimp any
wires between the baseplate and tube.
Install a lamp per the relamping instructions below and test the 5.
fixture for proper operation.
RELAMPING
Make sure power is off before relamping. Loosen the three head screws on top of the head assembly until the
assembly is loose. Lift the head assembly entirely off, lifting by the louvers, not the roof. Unscrew the
globe and set it aside. Replace the lamp or install a new one per the lamp style on the lamp label. HID fixtures
should use coated lamps for best results. Make sure the globe gasket is correctly seated, and securely replace
the globe. Set the head onto the fixture and tighten the three head screws securely.
32000950, revision F
100 Craftway Dr.
Littlestown, Pennsylvania 17340-0128
Phone: [phone]
INSTALLATION INSTRUCTIONS:
BOLLARDS
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.
page 1 of 2
SAFETY WARNING:
ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE
PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING!
This fixture can become very HOT! The fixture housing and lens, especially if it is glass, can become hot enough
to blister hands. Attention should be paid to where the fixture is mounted, particularly if it can be touched by
children or pets. To help prevent premature failure, decreased performance, overheating and risk of fire, keep
fixture and lens clean and free of leaves, mulch, debris and mineral deposits from water. The fixture and lens
can be cleaned using a soft cloth and a solution of mild liquid soap and warm water. Wipe clean and dry with a
soft, lint-free dry cloth. Avoid polishing fixture or lens.

30"
HID,
FLUOR.,
INC. & LED
21"
HID,
FLUOR.,
INC. & LED
14"
INC. & LED
ONLY
HEAD MOUNTING
SCREWS, (3X)
HEAD
ASSEMBLY
LAMP
GLOBE
TUBE
BALLAST
ASSEMBLY
QUICK-
CONNECT
CONDUIT STUB
(BY OTHERS)
BASE
PLATE
MOUNTING
SCREWS, (3X)
LEVELING NUTS (3X)
ANCHOR RODS (3X)
SET IN POURED
CONCRETE FOOTER
STANDARD
FIXTURE
STYLES
NOTE : FIXTURE STYLE AND BALLAST TYPE
WILL VARY WITH FIXTURE OPTIONS.
PICTURED TO THE RIGHT : 21" HID.
page 2 of 2
32000950, revision F
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS!
WARNING - Lamp gets HOT quickly! To reduce the risk of FIRE OR INJURY TO PERSONS:
Do not operate fixture with a missing or damaged lens/lens assembly.
Contact only switch or plug when turning fixture on or off. Do NOT touch hot lens or housing.
Turn off or unplug fixture and allow to cool before relamping. Keep lamp away from combustibles.
Do NOT touch lamp with bare hands at any time, use a soft cloth as oil from skin may damage lamp.