Philips Urbanspark BDP301 LED 4M 7043 User manual

Urbanspark
Mounting Instructions
(V1.0)
Philips (China) Investment Co., Ltd
Address:No. 1602-1605, No. 218 Tianmu W Rd, Shanghai
Post code: 200070

Important Safety Notice
The battery presents a risk of electrical shock and a high short circuit current. The
Philips mounting instructions must be strictly followed, otherwise potential application,
reliability, or safety issues may arise. Contact your local Philips service if the
instructions cannot meet special field conditions.
Only a qualified Philips service representative who is knowledgeable in batteries and
the required precautions is permitted to service the battery. Keep unauthorized
personnel away from batteries.
Danger:
1. The battery package maybe explode by shock, please be careful during handling.
2. When moving batteries. Wear all appropriate safety clothing and equipment.
3. Prohibit dispose of the batteries in a fire. The batteries could explode.
Caution:
1. The misuse of this equipment could result in human injury and/or equipment damage.
In no event will Philips be responsible or liable for either indirect or consequential
damage or injury that may have resulted from the misuse of this equipment.
2. Use tools with insulated handles to avoid inadvertent shorts.
3. Verify circuit polarities before connecting.
4. Connect sequence: a) connect load,; b) connect battery; c) connect charging
source.
4. Disconnect sequence: a) disconnect charging source; b) disconnect battery; c)
disconnect load.
Warning:
1. Failure to replace a battery before it becomes exhausted may cause the case to
crack, possibly releasing electrolytes from inside the battery and resulting in secondary
issues such as odor, smoke, and fire.
2. The battery system must be in proper maintenance according to the "Maintenance"
manual in this book. This is essential for safety and the reliability of the lighting system.
3. Do not dispose of batteries except through channels in accordance with local, state
and federal regulations.
Notice: The mounting instructions in this document is for standard solar lighting system
installation. It is vitally important that you observe the precautions recommended in this
manual.

1
Concrete
Field selection
Note:
1. The material is not provided by Philips,
2. The anchor bolts location dimensions
must be follow the drawings,
The concrete base size is different due to
local soil condition. You may consult to local
installation contractor.
3. You are just allowed install pole after the
concrete base solidification completely.
Cage
M20 Nuts,
Spring washers
Flat washers
235
235 60
M20 nuts (advise material:SUS)
Spring washers (advise material:SUS)
Flat washers (advise material:SUS)
Pole foundation and anchor bolts
Avoid Locations in the shade of the trees or buildings, if you can not avoid the shade, you must ensure the
shade below the 2m of the pole.
If you do want to install the system at a shade area, please consult to Philips professional people.
2m 2m
(unit: mm)

3
Pole
2
Note: The tools listed do not include items needed for pole installation and other construction work.
Part list
Tools
Controller
Battery
Luminaire
Cross screwdriverSpanner (Max
open size >30mm )
Multimeter
(optional)
Socket screw wrench
(Philips provided it)
Steel rope
(Φ1.5mm
length=8m)
Note: Luminaire may be different according to different requirements.

4Mount Luminaire
4. Pull the Luminaire cable through the pole by steel rope.
17N.m
4mm
torque
1. Open the package 2. Open the service hatch with
attached tool in the package.
3.Lift the top of the pole out of the package and put it on one edge of the package.
5. Tighten screws.

5Erect the Pole
Pull
Solution 1：By man-Power for 4m pole
For reference only
Lift by crane
Warning: Be careful not
to let luminaire hit the
crane arm.
Solution 2：By crane for 4m and 6m pole
For reference only
Affix the pole
Note:
Whoever installs the system
takes full responsibility for safety.
For reference only
Affix the pole by M20
Nuts, spring washers
and flat washers

System Connection
6
1. Put battery
into the pole.
3. FIRSTLY, connect luminaire to
the controller
2. Affix controller on
the beam of the pole
with four screws.
4. SECONDLY, connect NTC to
the controller
5. THIRDLY, connect battery to
the controller
6. LASTLY, connect PV
Panel to the controller
7. Check controller indicator
lighting status
LED 1: Green on
LED 2: Green on or flash
LED 3: Red off
8. Lock the service door at the end.
LED 3
LED 2 LED 1
Notice: Must strictly follow the below sequence, or it will introduce difficulty on installation.

Check List for Installation
(This checklist MUST be signed by the installer before system installation handover)
Person in charge of site construction
Signature/Date
Project Location
No. Item Description Result Remark
1
Installation
location
If the installation location avoid the shade of
the trees or buildings
□yes □No
2
Base
If structural strength of base meet loacl pole
requirement
□yes □No
3
Anchor bolts
If the anchor bolts location dimensions
follow the MI
□yes □No
4
Products If all components no damaged □yes □No
5
Bolts If four bols are fixed □yes □No
6
Work status If the work status comply to the request □yes □No
7
Luminire If the luminaire can light on □yes □No
8
PV panel
If the PV panel can charge the battery
normally.
□yes □No
Project Name
Scope of check
Site Consrtuctor

Troubleshooting
luminaire disconnect
Check if the the connection of
luminaire is loosing
luminaire overload
Replace a luminaire which suit for
the system
luminaire broken Replace a good luminaire
NTC disconnect Connect the NTC
NTC cable borken Replace a good NTC cable
LVD
Wait for several sun days for
recovering battery or recharge
the battery by charger
battery End of life Replace a good battery
battery broke Replace a good battery
CC broken Replace a good controller
Panel is interfered by other light
source
Check if there is other light
source irradiate at panel
Programe incorrect Re-burning the programe
Battery volume is low
Wait for several sun days for
recovering battery or recharge
the battery by charger
luminaire power is high Re-burning the programe
Part or all PV panel disconnection Connect all PV panel
dimming mode Re-burning the programe
RTE work mode enable Re-burning the programe
Power less than spec Re-burning the programe
LED chip broken Change LED PCB or luminaire
No light
Firstly,Check if you were followed the connection sequence we
mention prior.if not, please disconnect one of the battery cable, and
reconnect it, wait for 2-5 minutes, if still no light, please check follow
below steps
less work time
of light
low illuminance

Maintenance
Panel
------ Normally you don't need to clean the panel frequently. It depends on the local environment;
------ If in heavy dust area，It is required to clean the solar module regularly with a damp towel to guarantee
optimum performance of the solar panel;
------ Do not use any type of solvent for cleaning and be careful not to put too much pressure on the
module while cleaning;
------ You Should clean small ads regular;
------ You should trim the trees and branches which cover the PV panel regular;
Battery
------ Battery normally does not need any maintenance within the warranty. If any abnormal symptom or
special requirement, suggest following test can be taken:
1. Check whether there is some loose connection;
2. Measure and record ambient temperature in the pole;
3. Check the battery if it has deformation;
Battery Storage
The battery should be stored in clean and dry environment.
Storage time: battery is ex-work in fully charged, storage time should be limited. For ensuring battery
performance, do not exceed storage time as following definition:
Under -20℃~25℃, six months;
Under -20℃~35℃, three months;
Under -20℃~45℃, one month;
Warning
------ The recycle of the used battery should strictly follow the local laws and regulations. It is forbidden to
handle the battery as normal garbage for disposal;
------ Do not open, short circuit, or mutilate batteries as injury may occur;
------ Do not put the battery into a pool;
------ Never move battery by pulling the cables of the battery;
------ The installation is highly suggested during the day.
------ Only be charged with authorized charger by Philips.
------ Handle the panel pole and battery with great care during the installation and transportation;
------ ALWAYS keep sparks, flames and smoking materials away from the battery
------ In case of FIRE: To extinguish a fire of a battery, use CO2, foam, or dry chemical extinguishing media.
Do NOT discharge the extinguisher directly onto the battery. The resulting thermal shock may cause cracking
of the battery case/cover.
Important
If you have ANY question concerning safety when working with the battery system, contact your
local Philips sales/service representative to clarify any of the noted safety precautions, or, call the
corporate office number listed on the back of this manual and ask for professional service.
Maintenance