IMPORTANT: FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO
INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAM-
AGE. If you do not understand these warnings and instrucons, or if addional informaon is desired, please contact Philips at
Installaon, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local
laws, regulaons and electrical codes. This professional should be familiar with the construcon and operaon of this product and any hazards in-
volved. If not qualified, do not aempt installaon, service or maintenance.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all
warnings and instrucons included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construcon and operaon and any hazards involved.
CAUTION
RISK OF PRODUCT DAMAGE
Never connect luminaires and/or components under load with supply voltage turned on.
Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulaon.
Do not restrict fixture venlaon. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulaon, foam or other material that
will prevent convecon or conducon cooling.
Do not exceed luminaire maximum ambient temperature.
Do not modify the luminaire.
Only use luminaire in its intended applicaon and locaon.
Led products are polarity sensive. Ensure proper polarity before installaon.
Electrostac Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installaon and servicing of the luminaire.
Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance.
Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and con-
Always read the luminaires complete installaon instrucons prior to installaon for any addional luminaire specific warnings.
In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire operang within safe limits
Do not install damaged product. Handling and installing damaged products can potenally increase the risks menoned In case of damage and/or miss-
ing
parts
upon
arrival
of
the
luminaire,
please
contact
[email protected] phone 800-227-0758. These instrucons do not purport to cover all details or variaons in equipment nor to provide every possible conngency to meet in connecon with instal-
laon, operaon or maintenance. Should further informaon be desired or should parcular problems arise which are not covered sufficiently for the pur-
chaser’s
or
owner’s
purposes,
this
ma
er should be referred to [email protected] phone 800-227-0758. Please see luminaire specific Installaon and Maintenance Instrucon for addional warnings or any applicable FCC or regulatory statements. Failure to
follow any of these Instrucons could void luminaires warranes.
Luminaire Maintenance
Regular luminaire maintenance programs are recommended.
It is recommended to clean the outside of the luminaire and the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
If clean water is not sufficient for cleaning, use a neutral, synthec, not-scratching and not-abrasive cleaning substance.
Never use alkaline and/or acetous cleaning substances.
Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
Philips recommends using a cleaning soluon that has a PH between 5 and 8.
Recycle: For informaon on how to recycle electronic products and components, please visit www.epa.gov.
INSTALLATION INSTRUCTIONS PUREFORM BOLLARD (PBL)
WARNINGS AND INSTRUCTIONS FOR LUMINAIRES
WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY
Disconnect or turn offpower before aempng any installaon,
service or maintenance.
Verify that supply voltage is correct by referencing the luminaire
label informaon.
Make all electrical and ground connecons in accordance with
the Naonal Electrical Code (NEC) and any other applicable laws,
regulaons or codes.
All wiring connecons should be capped with UL-approved wire
connectors.
WARNING
RISK OF FIRE OR PERSONAL INJURY
Keep combusble materials away from LED/lamp & lens
Do not operate in close proximity to persons, combusble
materials or substances affected by heat or drying.
WARNING
RISK OF PERSONAL INJURY
Wear gloves and safety glasses at all mes when removing luminaire from
carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.
WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY
Allow Led/lamp & lens to cool before handling.
Do not touch enclosure or light source
Do not exceed maximum waage marked on luminaire label.
Follow all manufacturer’s warnings, recommendaons, instrucons and
restricons for driver type, burning posion, mounng locaons and
replacement.
© 2018 Philips Lighting Holding B.V. All rights reserved.
www.philips.com/luminaires
P/N 443560819190 Rev A
Page 1 of 4
