Philips AZ1850 User manual

Register your product and get support at
AZ1850
EN User manual

English
1 Important
Safety
Important Safety Instructions
aRead these instructions.
bKeep these instructions.
cHeed all warnings.
dFollow all instructions.
eDo not use this apparatus near water.
fClean only with dry cloth.
gDo not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
hDo not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers)
that produce heat.
iProtect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specied by the
manufacturer.
kUse only with the cart, stand, tripod, bracket, or
table specied by the manufacturer or sold with
the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury
from tip-over.
lUnplug this apparatus during lightning storms or when
unused for long periods of time.
m Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
nBattery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to
the unit:
Install all batteries correctly, + and - as marked on the•
unit.
Do not mix batteries (old and new or carbon and•
alkaline, etc.).
Remove batteries when the unit is not used for a long•
time.
The batteries shall not be exposed to excessive heat•
suchassunshine,reorthelike.
oApparatus shall not be exposed to dripping or splashing.
pDo not place any sources of danger on the apparatus (e.g.
liquid lled objects, lighted candles).
qThis product may contain lead and mercury. Disposal of
these materials may be regulated due to environmental
considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries
Alliance: www.eiae.org.

Important notes for users in the U.K.
Mains plug
Thisapparatusisttedwithanapproved13Ampplug.Tochangea
fuse in this type of plug proceed as follows:
1Remove fuse cover and fuse.
2 FixnewfusewhichshouldbeaBS13623Amp,A.S.T.A.orBSI
approved type.
3 Retthefusecover.
Ifthettedplugisnotsuitableforyoursocketoutlets,itshouldbe
cutoffandanappropriateplugttedinitsplace.
Ifthemainsplugcontainsafuse,thisshouldhaveavalueof3Amp.If
a plug without a fuse is used, the fuse at the distribution board should
notbegreaterthan3Amp.
Note:The severed plug must be disposed of to avoid a possible shock
hazard should it be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code:
blue = neutral (N), brown = live (L).
o As these colours may not correspond with the colour markings
identifying the terminals in your plug, proceed as follows:
– Connect the blue wire to the terminal marked N or coloured black.
– Connect the brown wire to the terminal marked L or coloured
red.
– Do not connect either wire to the earth terminal in the plug,
marked E (or e) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See
CopyrightAct1956andThePerformer’sProtectionActs1958to
1972.

Warning
Never remove the casing of this apparatus.•
Never lubricate any part of this apparatus.•
Never place this apparatus on other electrical equipment.•
Keepthisapparatusawayfromdirectsunlight,nakedamesorheat.•
Never look into the laser beam inside this apparatus.•
Ensure that you always have easy access to the power cord, plug or•
adaptor to disconnect this apparatus from the power.
Hearing Safety
Listen at a moderate volume:
Using headphones at a high volume can impair your hearing. This
product can produce sounds in decibel ranges that may cause
hearing loss for a normal person, even for exposure less than a
minute. The higher decibel ranges are offered for those that may
have already experienced some hearing loss.
Soundcanbedeceiving.Overtimeyourhearing‘comfortlevel’
adapts to higher volumes of sound. So after prolonged listening, what
sounds‘normal’canactuallybeloudandharmfultoyourhearing.To
guard against this, set your volume to a safe level before your hearing
adapts and leave it there.
To establish a safe volume level:
Set your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and
clearly, without distortion.
Listen for reasonable periods of time:
Prolongedexposuretosound,evenatnormally‘safe’levels,canalso
cause hearing loss.
Be sure to use your equipment reasonably and take appropriate
breaks.

Be sure to observe the following guidelines when using your
headphones.
Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume as your hearing adapts.
Donotturnupthevolumesohighthatyoucan’thearwhat’saround
you.
You should use caution or temporarily discontinue use in potentially
hazardous situations.
Do not use headphones while operating a motorized vehicle, cycling,
skateboarding,etc.;itmaycreateatrafchazardandisillegalin
many areas.
Where the MAINS plug or an appliance coupler is used as the•
disconnect device, the disconnect device shall remain readily
operable.
Caution
Use of controls or adjustments or performance of procedures other•
than herein may result in hazardous radiation exposure or other
unsafe operation.
Notice
This product complies with the radio interference
requirements of the European Community.
This product complies with the requirements of the following
directivesandguidelines:2004/108/EC+2006/95/EC
Anychangesormodicationsmadetothisdevicethatarenot
expresslyapprovedbyPhilipsConsumerLifestylemayvoidtheuser’s
authority to operate the equipment.

Recycling
Your product is designed and manufactured with high
quality materials and components, which can be recycled
and reused.
When you see the crossed-out wheel bin symbol attached
to a product, it means the product is covered by the
EuropeanDirective2002/96/EC:
Never dispose of your product with other household
waste.Pleaseinformyourselfaboutthelocalrulesontheseparate
collection of electrical and electronic products. The correct disposal
of your old product helps prevent potentially negative consequences
on the environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC,whichcannotbedisposedofwithnormalhousehold
waste.
When you see the crossed-out wheel bin symbol with the
chemicalsymbol‘Pb’,itmeansthatthebatteriescomply
with the requirement set by the directive for lead:
Pleaseinformyourselfaboutthelocalrulesonseparatecollectionof
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
Recording and playback of material might require consent. See
CopyrightAct1956andThePerformer’sProtectionActs1958to
1972.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
paper pulp (buffer) and polyethylene (bags, protective foam sheet.)

Your system consists of materials which can be recycled and reused
ifdisassembledbyaspecializedcompany.Pleaseobservethelocal
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
The making of unauthorized copies
of copy-protected material, including
computerprograms,les,broadcasts
and sound recordings, may be an infringement of copyrights and
constitute a criminal offence. This equipment should not be used for
such purposes.
Trademark notice
The USB-IF Logos are trademarks of Universal Serial
Bus Implementers Forum, Inc.
Windows Media and the Windows logo are trademarks,
or registered trademarks of Microsoft Corporation in
theUnitedStatesand/orothercountries.
This apparatus includes this label:
2 Your CD Soundmachine
Introduction
With this apparatus, you can enjoy music from audio discs, external
devices, and listen to radio stations.

The apparatus offers you multiple sound effect settings that enrich sound
with Digital Sound Control (DSC) and Dynamic Bass Boost (DBB).
The apparatus supports the following media formats:
Note
The type plate is located on the back of the apparatus.•
What’s in the box
Check and identify the contents of the package:
Main unit•
AC power cord•
Remote control•
User Manual•
Quick Start Guide•

Overview of the main unit
a
Headphone socket.•
bMP3 LINK
Jack for an external audio device.•
c
Turnon/offtheunit.•
d
Stop play.•
Erase a program.•
Start or pause play.•

e/
Skiptotheprevious/nexttrack.•
Tune to a radio station.•
Search within a track.•
fALBUM/PRESET -/+
Select a preset radio station.•
Skiptotheprevious/nextalbum.•
gPROGRAM
Programtracksandbrowsetheprogram.•
MODE
Selectaplaymode:REPEATorSHUFFLE.•
hSOURCE
Select a source.•
iIR
Remote control senser.•
j- VOLUME +
Adjust volume.•
kDisplay panel
Display current status.•
l
USB socket.•
mDBB
Turnon/offdynamicbassboost.•
DSC
Select a preset sound setting.•
n OPEN•CLOSE
Open/closethedisccompartment.•
oAntenna

Overview of the remote control
aCD
Select disc source.•
b/
Skiptotheprevious/nextalbum.•
Select a preset radio station.•
/
Skiptotheprevious/nexttrack.•
Start or pause play.•
c/
Search within a track.•

dPROG
Programradiostations.•
Programtracks.•
eREPE AT
Select repeat play modes.•
SHUFFLE
Selectshufeplaymodes.•
fDBB
Turnon/offdynamicbassboost.•
gDSC
Select a preset sound setting.•
hVOL +/-
Adjust volume.•
iSLEEP
Set the sleep timer.•
Turnon/offthescreenbacklightofmainunit.•
jMUTE
Mute or restore volume.•
k
Stop play.•
Erase a program.•
lUSB
Select USB source.•
mTUNER
Select tuner source.•

3 Get started
Caution
Use of controls or adjustments or performance of procedures other•
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
IfyoucontactPhilips,youwillbeaskedforthemodelandserialnumber
of your apparatus.The model number and serial number are on the
bottom of your apparatus.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
Note
You can use both batteries and AC power as power supply of this•
apparatus.
Batteries are not supplied with the accessories.
•
1Open the battery compartment.
2 Insert6batteries(type:R-20,UM-1orD-cells)withcorrect
polarity(+/-)asindicated.
3Close the battery compartment.

Prepare the remote control
Caution
Riskofexplosion!Keepbatteriesawayfromheat,sunshineorre.•
Neverdiscardbatteriesinre.
Risk of decreased battery life! Never mix different brands or types
•
of batteries.
Risk of product damage! When the remote control is not used for
•
long periods, remove the batteries.
For rst-time use:
1Remove the protective tab to activate the remote control
batteries.
To replace the remote control batteries:
1Open the battery compartment.
2 Insert1CR2025batteriewithcorrectpolarity(+/-)as
indicated.
3Close the battery compartment.

Connect power
Warning
Risk of product damage! Ensure that the power supply voltage•
corresponds to the voltage printed on the back or the underside of
the apparatus.
Risk of electric shock! When you disconnect the AC power, always
•
pull the plug from the socket. Never pull the cord.
Note
Install the apparatus near the power supply socket and where the•
power plug can be easily reached.
1Connect the AC power cord to the AC input jack on the
apparatus and to the power supply socket.
To switch the apparatus off completely, disconnect the•
AC power cord from the power supply socket.

Note
To save energy: after use, turn off the apparatus.•
Turn on
1 Press .
The unit switches to the last selected source.»
4 Play
Play CD
1 PressCD to select the disc source.
2 PressOPEN•CLOSE to open the disc tray.
3Insert a disc with the printed side facing up, then close the disc
tray.
Playstartsautomatically.»
Topause/resumeplay,press• .
ACMAINS
~

To stop play, press• .
ForMP3/WMAles:toselectanalbum,press• /.
To skip to a track, press• /.
To search within a track, press and hold• /. Release
to resume normal play.
Play from USB devices
Note
Ensure that the USB device contains playable audio contents for•
supported formats.
1Insert the USB connector on the device into the socket.
2Select USB source.
3 Press / unit to select a folder.
4 Press / toselectale.
5 Press to start play.
To stop play, press• .
To pause or resume play, press• .
Listen to an external device
YoucanlistentoanMP3playerthroughthisapparatus.
1 Useacablewith3.5mmplugsonbothends(notsupplied)to
connect MP3 LINKjack(3.5mm)onthisapparatusandthe
headphonejackonanMP3player.

5 Play options
Adjust volume level
1During play, press VOL +/-toincrease/decreasethevolume
level.
Select a preset sound effect
1During play, press DSC repeatedly to select:
[POP](pop)•
[JAZZ](jazz)•
[CLASSIC](classic)•
[ROCK](rock)•
Enhance bass
1During play, press DBB to turn on or off dynamic bass
enhancement.
If DBB is activated, DBB is displayed.»
Mute sound
1During play, press MUTEtomute/unmutesound.
Select play modes
1 PressMODE repeatedly to select a play mode:
• [](repeat) – repeat a track
• [ALL](repeatall)-repeatanentireCD/program
• [] (shufe)-playtracksrandomly

• [ ](shuferepeatall)-repeatalltracks
randomly.
2To return to normal play, press MODE repeatedly until play
mode icons are no longer displayed.
Tip
Only•and can be selected when you play programmed
tracks.
Program tracks
Youcanprogramamaximumof20tracks.
1 InCD/USBmode,atthestopposition,pressPROG to activate
the program mode.
[PROG](program)startstoblinks.»
2 ForMP3/WMAtracks,pressALBUM/PRESET +/- to select an
album.
3 Press / to select a track number, then press PROG to
conrm.
4 Repeatsteps2to3toprogrammoretracks.
5 Press to play the programmed tracks.
Duringplay,[PROG](program)isdisplayed.»
To erase the program, in the stop position, press• .
To review the program, in the stop position, press and•
hold PROGformorethan2seconds.