Philips BT3600 User manual

www.philips.com/support
BT3600
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips

1EN
Contents
1 Important 2
2 Your Bluetooth speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Place the speaker 5
Charge the built-in battery 5
Turn on/off 5
4 Use Bluetooth devices 6
Connect a device 6
Connect two Bluetooth devices
simultaneously 7
Play from Bluetooth device 7
Control your phone call 7
5 Listen to an external device 8
6 Product information 9
Specications 9
7 Troubleshooting 10
General 10
About Bluetooth device 10
8 Notice 11
Compliance 11
Care of the environment 11
Trademark notice 12

2EN
1 Important
Warning
• Never remove the casing of this speaker.
• Never lubricate any part of this speaker.
• Never place this speaker on other electrical equipment.
• Keep this speaker away from direct sunlight, naked
amesorheat.
• Do not use this speaker near water.
• Make sure that there is enough free space
around the speaker for ventilation.
• Only use attachments or accessories
speciedbythemanufacturer.
• The battery shall not be exposed to
excessiveheatsuchassunshine,reorthe
like.
• The speaker shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on
thespeaker(e.g.liquidlledobjects,lighted
candles).
Note
• The type plate is located on the back of the product.

3EN
2 Your Bluetooth
speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can
• enjoyaudiofromyourBluetooth-enabled
devices or other external audio devices;
and
• control the incoming phone call through
Bluetooth connection.
What's in the box
Check and identify the contents of your
package:
• Main unit
• USB cable
• Short user manual
• Safetyandnoticeleaet

4EN
Overview of the speaker
a DC IN
• Recharge the built-in battery.
b AUDIO IN
• Connect an external audio device.
c MULTIPAIR
• Press and hold for two seconds to
enter pairing mode.
• Press and hold for two seconds to
clear idle Bluetooth devices connected
to the speaker.
• Press to answer an incoming call.
• Press and hold for two seconds to
rejectanincomingcall.
• During a call, press to end the current
phone call.
• During a call, press and hold for two
seconds to transfer the call to your
mobile device.
d /Volume knob
• Turn the speaker on or off.
• Adjustvolume.
e LED indicator
• Indicate system status.
f NFC
• Connect a NFC compatible device
through Bluetooth.
a
b
c
d
e
f

5EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Place the speaker
Toplacethespeakeronaatsurface,pullout
the retractable stand from the backside of the
speaker.
Charge the built-in battery
The speaker is powered by the built-in
rechargeable battery.
Note
• Before use, fully charge the built-in battery.
• The micro USB socket is for charging only.
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
Connect the USB cable between
• the DC IN socket on the speaker, and
• a USB socket on a computer.
DC IN
The LED indicator indicates the battery status.
Mode LED indicator Battery status
"Off" mode Solid red Under charging
Off Fully charged
"Bluetooth"
or "Audio-in"
mode
Flashing red Low battery
Turn on/off
Rotate the knob clockwise or anticlockwise
to turn the speaker on or off.
» When the speaker is turned on, the
LEDindicatorashes.
Note
• During play, rotate the knob to increase or decrease
volume.
• If there is no operation for 15 minutes, the speaker
switches to standby mode automatically for power
saving.
ON
OFF

6EN
4 Use Bluetooth
devices
With this speaker, you can listen to audio from
Bluetooth-enabled devices and control the
incoming call through Bluetooth.
Connect a device
Note
• Before pairing a device with this speaker, read its user
manual for Bluetooth compatibility.
• The speaker can memorize a maximum of four paired
devices.Thefthpaireddevicewillreplacetherstone.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this speaker and a Bluetooth
device can reduce the operational range. Keep away
from any other electronic device that may cause
interference.
• The operational range between this speaker and a
Bluetooth device is approximately 10 meters (30 feet).
• Make sure that no audio-in cable is connected to the
AUDIO IN socket.
Connect a device through NFC
Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this speaker easily.
1 Turn on the speaker.
» TheLEDindicatorashesblue.
2 Enable the NFC feature on your Bluetooth
enabled device (refer to the user manual
of the device).
3 Tap the NFC tag on the speaker with the
NFC area of your Bluetooth device.
4 On your Bluetooth device, accept the
pairing request with "BT3600". If necessary,
input "0000" as the pairing password.
5 Follow the on-screen instructions to
complete the pairing and connection.
» After successful pairing and connection,
the speaker beeps twice, and the LED
indicator turns solid blue.
Connect a device manually
1 Turn on the speaker.
» TheLEDindicatorashesblue.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
(refer to the user manual of the device).
3 When [Philips BT3600] is displayed on
your device, select it to start pairing and
connection. If necessary, enter default
password “0000”.
» After successful pairing and connection,
the speaker beeps twice, and the LED
indicator turns solid blue.
• Ifyoufailtond[Philips BT3600] for
pairing, press and hold MULTIPAIR
for two seconds to enter pairing mode,
and then try again.
To disconnect the Bluetooth-enabled device:
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» The speaker beeps twice, and the LED
indicatorashes.

7EN
Connect two Bluetooth
devices simultaneously
The speaker can connect to two Bluetooth
devices at the same time.
1 Connect one Bluetooth device.
2 Press and hold MULTIPAIR for two
seconds.
» The speaker is ready to pair with one
more Bluetooth device.
» TheLEDindicatorashesblue.
3 Connect the other Bluetooth device.
• If the speaker is connected to two devices
and only one device is playing music, press
and hold MULTIPAIR for two seconds.
» The speaker disconnects the idle
device, and gets ready to pair with
another device.
• If the speaker is connected to two devices
and both are not playing music, press and
hold MULTIPAIR for two seconds.
» Thespeakerdisconnectstherst
paired device, and gets ready to pair
with another device.
LED indicator Description
Flashing blue quickly Pairing
Flashing blue slowly Connecting
Solid blue Connected
2 sec.
Play from Bluetooth device
Note
• If there is an incoming call on the connected mobile
phone, music play pauses.
After successful Bluetooth connection, play
audio on any connected Bluetooth device.
» Audio streams from your Bluetooth
device to the speaker.
Control your phone call
After Bluetooth connection, you can control an
incoming call with this speaker.
Button Function
Press to answer an incoming call.
Press and hold for two seconds to
rejectanincomingcall.
During a call, press to end the current
call.
During a call, press and hold for two
seconds to transfer the call to your
mobile device.
Note
• Music play pauses when there is an incoming call, and
resumes when your phone call ends.

8EN
5 Listen to an
external device
With this speaker, you can also listen to an
external audio device such as an MP3 player.
Note
• Make sure that music playback through Bluetooth is
stopped.
1 Connect an audio input cable (not
supplied) with a 3.5 mm connector on
both ends to
• the AUDIO IN socket on this speaker,
and
• the headphone socket on the external
device.
2 Play audio on the external device (refer to
its user manual).