Philips DTM9030 User manual

www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
DTM9030
Question?
Contact
Philips

1
English
EN
Contents
1 Safety and Notice 2
Safety 2
Notice 4
2 Your Docking Entertainment System 5
Introduction 5
What’s in the box 5
Overview of the main speaker 6
Overview of the remote control 8
3 Get started 10
Connect speaker cables 10
Connect FM antenna 11
Connect power 11
Prepare the remote control 11
Set clock 12
Turn on 12
4 Play 13
Play from a disc 13
Play from USB 13
5 Play options 14
Pause/resume play 14
Stop play 14
Skip to a track 14
Search within a track 14
Repeat and shufe play 14
Program tracks 14
Display ID3 information 14
6 Play from a Bluetooth device 15
7 Play iPod/iPhone 16
Compatible iPod/iPhone 16
Load the iPod/iPhone 16
Listen to the iPod/iPhone 16
Charge the iPod/iPhone 17
Remove the iPod/iPhone 17
8 Listen to the radio 18
Tune to a radio station 18
Select stereo/mono broadcast 18
Program radio stations 18
Select a preset radio station 18
Display play information 19
9 Adjust sound 20
Adjust volume 20
Adjust bass/treble level 20
Mute sound 20
10 Other features 21
Set the sleep timer 21
Set the alarm timer 21
Play from an external device 21
11 Product information 23
Specications 23
USB playability information 24
Supported MP3 disc formats 24
12 Troubleshooting 25
Contents

2EN
1 Safety and
Notice
Read and understand all instructions before you
use this product. If damage is caused by failure
to follow the instructions, the warranty does
not apply.
Safety
Warning
•Never remove the casing of this apparatus.
•Never lubricate any part of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Keep this apparatus away from direct sunlight, naked
ames or heat.
•Never look into the laser beam inside this apparatus.
•Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
i Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
j Only use attachments/accessories
specied by the manufacturer.
k Use only with the cart, stand, tripod,
bracket, or table specied by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
l Unplug this apparatus during lightning
storms or when unused for long periods
of time.
m Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
n Apparatus shall not be exposed to
dripping or splashing.
o Do not place any sources of danger on
the apparatus (e.g. liquid lled objects,
lighted candles).
p Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
q Make sure there is enough free space
around the product for ventilation.
r Batteries (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine, re or
the like.

3
English
EN
Important notes for users in the U.K.
Mains fuse
This information applies only to products with a
UK mains plug.
This product is tted with an approved molded
plug. If you replace the fuse, use one with:
• the ratings shown on the plug,
• a BS 1362 approval, and
• the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution:To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
How to connect a plug
The wires in the power cord are colored as
follows: blue = neutral (N), brown = live (L).
If the colors do not correspond with the colors
on your plug, identify the terminals in your plug
as follows:
1 Connect the blue wire to the terminal
marked N or colored black.
2 Connect the brown wire to the terminal
marked L or colored red.
3 Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
colored green (or green and yellow).
Before you replace the plug cover, make sure
that the cord grip is clamped over the sheath
of the cable and not just over the two wires in
the cable.
Care for your product
• Do not insert any objects other than discs
into the disc compartment.
• Do not insert warped or cracked discs into
the disc compartment.
• Remove the discs from the disc
compartment if you are not using the
product for an extended period of time.
• Only use microber cloth to clean the
product.
Care of the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Note
•The type plate is located on the back of the apparatus.

4EN
Notice
Hereby,WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC. You can nd the
Declaration of Conformity on www.philips.com/
support.
Any changes or modications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.”
Specications are subject to change without
notice.WOOX reserves the right to change
products at any time without being obliged to
adjust earlier supplies accordingly.
The making of unauthorized copies of copy-
protected material, including computer
programs, les, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Windows Media and the Windows logo
are trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specically to iPod or
iPhone respectively, and has been certied by
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPod or iPhone
may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
The Bluetooth®word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license.
© 2013 CSR plc and its group companies.
The aptX®mark and the aptX logo are
trade marks of CSR plc or one of its group
companies and may be registered in one or
more jurisdictions.

5
English
EN
2 Your Docking
Entertainment
System
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this unit, you can:
• enjoy audio from discs, USB devices, iPod/
iPhone, Bluetooth devices, and other
external devices
• listen to radio stations
The unit supports the following media
formats:
What’s in the box
Check and identify the contents of your
package:
• Main unit
• Remote control with two AAA batteries
• Power cord
• Speaker connection cable
• FM antenna
• Printed materials

6EN
Overview of the main
speaker
a Bluetooth indicator
b
• USB socket.
c
• Eject the disc.
d Disc compartment
e Dock cover
• Lift up to expose the dock connectors.
f Dock for iPod/iPhone with 30-pin
connection
g Dock for iPod/iPhone with lightning
connection
h Display panel
• Show the current status.
a
b
c
d
e
f
g
h
i
j
k
p
q
r
s
n
o
m
l
v
u
t
i +/-
• Adjust volume.
j /
• In Disc/USB/Dock source, tap to skip
to the previous/next track.
• In Disc/USB/Dock source, tap and hold
to search within a track.
• In tuner source, tap to tune to a radio
station.
• Tap to set clock and timer.
k
• Turn the unit on.
• Switch to standby mode or Eco power
standby mode.

7
English
EN
l
• Start or pause play.
m
• Stop play or erase a program.
n SOURCE
• Select a source: DISC, USB, FM TUNER,
dock (IPOD_IPHONE), BLUETOOTH,
AUX,AUDIO_IN, OPTICAL, or
COAXIAL.
o BT SETUP
• (Press and hold) remove the existing
pairing information.
p AUX IN (L/R)
• Sockets for RCA (red/white) audi
input.
q FM AERIAL
• Socket for FM antenna connection.
r Speaker connectors
• Sockets for speaker connection.
s AC~MAINS
• Power supply socket.
t AUDIO IN
• 3.5mm audio input socket.
u OPTICAL IN
• Optical input socket.
v COAXIAL IN
• Coaxial input socket.

8EN
Overview of the remote
control
a
• Turn the unit on.
• Switch to standby mode or Eco power
standby mode.
b AUDIO IN/AUX
• Select the 3.5mm or RCA (red/white)
audio input source.
c USB
• Select the USB source.
d DOCK/MENU
• Select the dock (IPOD_IPHONE)
source.
• Access the iPod/iPhone menu.
a
b
c
d
e
f
g
h
i
j
k
l
m
no
p
r
q
s
t
u
e PAIRING
• Select the Bluetooth source.
f ALBUM +/- /
• Skip to previous/next album.
• Navigate through the iPod/iPhone
menu.
g OK/INFO/RDS
• Conrm a selection.
• Select display information during play.
• Display Radio Data System (RDS)
information.
h /
• In Disc/USB/Dock source, press to
search within a track.
• In tuner source, press to tune to a
radio station.
• Navigate through the iPod/iPhone
menu.
i BASS/TREBLE
• Adjust the bass/treble level.
j
• Stop play or erase a program.
k /
• In Disc/USB/Dock source, press to skip
to the previous/next track.
• Set clock and timer.
• Select a preset radio station.
l
• Mute or restore sound.
m Numeric keypad
• Select a track.
• Select a preset radio station.
n TIMER/SLEEP
• Set the sleep timer.
• Set the alarm timer.

9
English
EN
o PROG/CLOCK SET
• In Disc/USB source, press and hold to
program tracks.
• In tuner source, press and hold to
program radio stations.
• In standby mode, press and hold to set
the clock.
p VOL +/-
• Adjust volume.
q
• Start or pause play.
r MODE/MONO/STEREO
• Select the repeat/shufe play mode.
• Switch between STEREO and MONO
in tuner mode.
s OPT/COAX
• Select the coaxial or optical input
source.
t FM
• Select the FM tuner source.
u DISC
• Select the disc source.

10 EN
3 Get started
Caution
•Use of controls, or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this device.The
model number and serial number are on the
back of the device.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect speaker cables
Note
•Insert the stripped portion of each speaker wire into
the socket completely.
•For optimal sound, use the supplied speakers only.
1 Unscrew the speaker connectors.
2 Insert fully the end of a speaker cable with
red mark into the left red (+) connector.
3 Screw the left red (+) connector to secure
the cable.
4 Insert fully the end of a speaker cable
without red mark into the left black (-)
connector.
5 Screw the left black (-) connector to
secure the cable.
6 Repeat steps 2-5 to insert the other
speaker cable into the right connectors.
2
13

11
English
EN
Connect FM antenna
Tip
•For optimal reception, fully extend and adjust the
position of the antenna.
• Connect the supplied FM antenna to the
FM AERIAL socket on the back of the
main speaker.
Connect power
Caution
•Risk of product damage! Ensure that the power supply
voltage corresponds to the voltage printed on the back
or the underside of the unit.
•Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
•Before connecting the AC power cord, ensure you have
completed all other connections.
• Connect the power cord to:
• the AC~MAINS socket on the back of
the main speaker.
• the wall outlet.
Prepare the remote control
Caution
•Risk of explosion! Keep batteries away from heat,
sunshine, or re. Never discard batteries in re.
To insert the remote control battery:
1 Open the battery compartment.
2 Insert 2 AAA batteries with correct
polarity (+/-) as indicated.
3 Close the battery compartment.

12 EN
Note
•If you are not going to use the remote control for a
long time, remove the batteries.
•Do not use old and new or different types of batteries
in combination.
•Batteries contain chemical substances, so they should
be disposed of properly.
Set clock
1 In standby mode, press and hold PROG/
CLOCK SET for more than two seconds
to activate clock setting mode.
» The 12 hour or 24 hour format is
displayed.
2 Press / to select 12 hour or 24 hour
format, and then press PROG/CLOCK
SET.
» The hour digits are displayed and begin
to blink.
3 Press / to set the hour, and then press
PROG/CLOCK SET.
» The minute digits are displayed and
begin to blink.
4 Press / to set the minute.
5 Press PROG/CLOCK SET to conrm.
Turn on
• Press .
» The unit switches to the last selected
source.
Switch to standby
• Press again to switch the unit to standby
mode.
» The backlight on the display panel is
reduced.
» The clock (if set) appears on the
display panel.
To switch to Eco power standby mode:
• Press and hold for more than two
seconds.
» The backlight on the display panel
turns off.
To switch between normal standby mode and
Eco power standby mode:
• Press and hold for more than two
seconds.
Note
•If no button is pressed over 15 minutes in standby
mode, this unit goes to Eco power standby mode
automatically.

13
English
EN
4 Play
Play from a disc
Note
•This unit is incompatible with a 8 cm disc.
1 Press DISC to select the disc source.
2 Insert a disc into the disc compartment
with the printed side facing left.
» The le starts playing automatically. If
not, press .
• Press on the top of the main
speaker to eject the disc out of the
disc compartment.
Play from USB
Note
•Make sure that the USB device contains playable audio
content.
1 Press USB to select the USB source.
2 Insert the USB device into the (USB)
socket on the top of the main speaker.
» The le starts playing automatically. If
not, press .

14 EN
5 Play options
Pause/resume play
• During play, press to pause/resume play.
Stop play
• During play, press to stop play.
Skip to a track
For CD:
• Press / to select another track.
• To select a track directly, press a key on
the numerical keypad.
For MP3 disc and USB:
1 Press ALBUM +/- / to select an
album or folder.
2 Press / to select a track or le.
Search within a track
1 During play, press and hold / to
search within a track.
2 Release to resume normal play.
Repeat and shufe play
1 During play, press MODE/MONO/
STEREO repeatedly to select:
• (repeat one):The current track is
played repeatedly.
• (repeat all): All tracks are played
repeatedly.
• (shufe): All tracks are played in a
random sequence.
2 To return to normal play, press
MODE/MONO/STEREO repeatedly until
repeat/shufe mode is no longer displayed.
Note
•The repeat and shufe play cannot be activated at the
same time.
•Shufe play cannot be selected when you play
programmed tracks.
Program tracks
You can program a maximum of 20 tracks.
1 In CD/USB mode, at the stop position,
press PROG/CLOCK SET to activate the
program mode.
» [PROG] (program) blinks on the
display.
2 For MP3/WMA tracks, press ALBUM +/-
/ to select an album.
3 Press / to select a track number, and
then press PROG/CLOCK SET to conrm.
4 Repeat steps 2 to 3 to program more
tracks.
5 Press to play the programmed tracks.
» During play, [PROG] (program) is
displayed.
• To erase the program, in the stop
position, press .
Display ID3 information
• In disc mode, during play, press OK/INFO/
RDS to display the following information:
• Track number
• Play time
• Title name
• Artist name
• Album name

15
English
EN
6 Play from a
Bluetooth
device
Note
•Before you connect a Bluetooth-enabled device to the
unit, familiarize yourself with the Bluetooth capabilities
of the device.
•Keep the unit away from other electronic devices that
may cause interference.
•The effective operation range between the unit and the
paired device is approximately 10 meters (30 feet).
•Any obstacle between the unit and the device can
reduce the operational range.
1 Press PAIRING to select the Bluetooth
source.
» The Bluetooth indicator ashes blue.
2 Activate the Bluetooth function on your
Bluetooth device (see the device user
manual).
3 Select ‘PHILIPS DTM9030’ on your device
for pairing.
» The Bluetooth indicator turns solid
blue.
» The unit beeps.
• For some devices, you may need to
input “0000” as the pairing password.
4 Start music play on your Bluetooth
enabled device.
Tip
•If the unit switches from Bluetooth source to other
sources, the connected Bluetooth device disconnects
automatically.
•The unit can memorize up to 8 previously connected
Bluetooth devices.
To disconnect the Bluetooth-enabled device:
• Deactivate Bluetooth on your device; or
• Move the device beyond the
communication range.
To clear Bluetooth pairing history:
• Press and holdBT SETUP on the main
speaker for 3 seconds.
» The current Bluetooth connection is
disconnected.
» After successful clearing, the Bluetooth
indicator ashes blue.
BT
0000
PIN
PHILIPS
DTM9030

16 EN
7 Play iPod/iPhone
You can enjoy audio from iPod/iPhone through
this unit.
Compatible iPod/iPhone
With the integrated dual docks, the unit
supports the following iPod, and iPhone models:
Made for (lightning connection):
• iPhone 5
• iPod nano (7th generation)
• iPod touch (5th generation)
Also made for (30-pin connection):
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
• iPod nano (2nd/3rd/4th/5th/6th
generation)
• iPod classic
• iPod touch (1st/2nd/3rd/4th generation)
Load the iPod/iPhone
Note
•You can only use one dock each time.
1 Lift up the dock cover.
2 Connect your iPod/iPhone to the lightning
or 30-pin dock connector.
Listen to the iPod/iPhone
Note
•Make sure that your iPod/iPhone has been loaded
securely.
1 Press DOCK/MENU to select the dock
source.
2 Play audio on your iPod/iPhone.
• To navigate in the menu: press
DOCK/MENU, and press / /
/ to select, and then press
OK/INFO/RDS to conrm.
• To pause/resume play, press .
• To skip to a track, press / .
• To search during play, press and hold
/ , then release to resume
normal play.

17
English
EN
Charge the iPod/iPhone
• When the unit is connected to power,
the docked iPod/iPhone begins to charge
automatically.
Remove the iPod/iPhone
• Pull the iPod/iPhone out of the dock.

18 EN
8 Listen to the
radio
Tune to a radio station
Tip
•For optimal FM reception, fully extend and adjust the
position of the FM antenna.
1 Press FM to select the FM tuner source.
2 Press and hold / for more than two
seconds.
» [SEARCH] (search) is displayed.
» The radio tunes to a station with
strong reception automatically.
3 Repeat step 2 to tune to more stations.
• To tune to a weak station, press /
repeatedly until you nd optimal
reception.
Select stereo/mono broadcast
For stations with weak signals: to improve the
reception, change to monaural sound.
• In FM tuner source, press MODE/MONO/
STEREO to select a setting:
• [STEREO]: stereo broadcast.
• [MONO]: monaural broadcast.
Program radio stations
Tip
•You can program a maximum of 20 preset radio
stations.
Program radio stations automatically
• In FM tuner mode, press and hold PROG/
CLOCK SET for more than two seconds
to activate automatic programming.
» [AUTO SRCH](auto search) is
displayed.
» All available stations are programmed
in the order of waveband reception
strength.
» The rst programmed radio station is
broadcast automatically.
Program radio stations manually
1 Tune to a radio station.
2 Press PROG/CLOCK SET to activate
program mode.
» [PROG] (program) blinks on the
display.
3 Press / to allocate a number (1 to 20)
to this radio station, and then press PROG/
CLOCK SET to conrm.
» The preset number and the frequency
of the preset station are displayed.
4 Repeat the above steps to program other
stations.
Note
•To overwrite a programmed station, store another
station in its place.
Select a preset radio station
• In FM tuner mode, press / to select a
preset number.
• You can also press the numeric key to
select a preset number directly.