Philips FW-C220 User manual

1
3139 115 20671
Mini Hi-Fi System
FW-C220
FW-C220
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM1

2
3139 115 20671
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1Remove fuse cover and fuse.
2Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
¶As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
– Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio FW-C220 Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven,The Netherlands
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM2

3
3139 115 20671
STANDBY-ON
PROGRAM DIM
FULL AUTO STOP
PLAYBACKPLAY/REC
MINI HIFI SYSTEM
C D 1 • 2 • 3 BAND TAPE 1 • 2
TAPECD TUNER AUX
PRESET
▲
▲
TUNING
▲ ▲ ▲ ▲
STOP • CLEAR
SEARCH PLAY• PAUSE PREV NEXT
DISC CHANGE
DISC 3
OPEN •CLOSE
DC
3
CHANGER
3 CD ROTARY CHANGER SYSTEM
3 CD ROTARY CHANGER SYSTEM
•
CD REWRITABLE COMPATIBLE
CD REWRITABLE COMPATIBLE
•
CD SYNCHRO RECORDING
CD SYNCHRO RECORDING
•
D
B
B
VIDEO
O
P
T
I
M
A
L
J
A
Z
Z
R
O
C
K
T
E
C
H
N
O
DSC
DISC 2
DISC 1
RECORD DUBBING A.REPLAY
DIGITAL SOUND CONTROL VOLUME
CLOCK•TIMER
NEWSRDS
0
▲OPEN
TAPE 2
TAPE 1
▲OPEN
DEMO STOP
0
9
8
1
2
3
4
5
6
7
™
!
@
#
$
%
^
&
*
(
)
¡
3
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM3

4
3139 115 20671
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM4

5
English
Français
Português EspañolDeutschNederlandsItalianoSvenskaDanskSuomi
∂ÏÏËÓÈο
3139 115 20671
Index
English ------------------------------------------------ 6
Français -------------------------------------------- 29
Español --------------------------------------------- 53
Deutsch --------------------------------------------- 77
Nederlands -------------------------------------- 101
Italiano -------------------------------------------- 125
Svenska ------------------------------------------- 149
Dansk --------------------------------------------- 173
Suomi --------------------------------------------- 197
Português ---------------------------------------- 221
∂ÏÏËÓÈο ----------------------------------------- 245
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM5

6
English
3139 115 20671
Contents
General Information
Environmental Information ................................ 7
Supplied Accessories ........................................... 7
Safety Information ................................................ 7
Preparation
Rear Connections ............................................. 8-9
Inserting batteries into the Remote Control ...
.................................................................................. 9
Controls
Controls on the player and remote
control .............................................................. 9-10
Operating the System
Plug and Play .................................................. 11-12
Demostration Mode .......................................... 12
Switching On ....................................................... 12
Switching the system to standby mode ........ 12
Selecting the source .......................................... 12
DIM mode ...................................................... 12-13
Sound Control .................................................... 13
Compact Disc
Discs for playback .............................................. 14
Loading the CD Changer ................................. 14
CD Direct Play .................................................... 14
Playing a Disc ....................................................... 15
Disc Change ........................................................ 15
Selecting a desired track ................................... 15
Searching for a particular passage
during playback ................................................... 15
Programming Tracks ........................................... 15
Reviewing the programme ............................... 16
Playing the programme ..................................... 16
Erasing the programme ..................................... 16
Shuffle .................................................................... 16
Repeat ................................................................... 16
Tuner
Tuning to radio stations .................................... 17
Storing Preset Stations ................................ 17-18
Tuning to Preset Radio Stations ...................... 18
Receiving RDS Radio Station ..................... 18-19
News ..................................................................... 19
Ta p e
Loading a tape ..................................................... 20
Auto Replay ......................................................... 20
Tape Playback ...................................................... 20
Rewind/Fast Forward ........................................ 21
Aux
Selecting External Equipment .......................... 21
Recording
One Touch Recording ........................................ 22
CD Synchro Start Recording........................... 23
Dubbing tapes ..................................................... 23
Recording from other sources ........................ 23
Clock/Timer
View Clock .......................................................... 24
Clock Setting ....................................................... 24
Timer Setting ................................................. 24-25
Sleep Timer .......................................................... 25
Specifications .......................................................26
Maintenance .........................................................27
TroubleShooting .....................................27-28
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM6

7
English
3139 115 20671
General Information
¶The type plate (which contains the serial
number) is located at the rear of the player.
¶Recording is permissible if copyright or
other rights of third parties are not
infringed.
¶This product complies with the radio
interference requirements of the European
Community.
Environmental Information
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Supplied Accessories
– Remote control
– AM loop antenna
– FM wire antenna
– AC power cord
Safety Information
¶Before operating the player, check that the
operating voltage indicated on the typeplate (or
the voltage indication beside the voltage
selector) of your player is identical with the
voltage of your local power supply. If not, please
consult your dealer.The typeplate is located at
the rear of your player.
¶When the player is switched on, do not move it
around.
¶Place the player on a solid base (e.g. a cabinet).
¶Place the player in a location with adequate
ventilation to prevent internal heat build-up in
your player. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from the each side.
¶Do not expose the player to excessive moisture,
rain, sand or heat sources.
¶Under no circumstances should you repair the
player yourself, as this will invalidate the
warranty!
¶If the player is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the player. Should this occur, the CD
player will not operate normally. Leave the
power on for about one hour with no disc in the
player until normal playback is possible.
¶Electrostatic discharge may cause unexpected
problems. See whether these problems
disappear if you unplug the AC power cord and
plug it in again after a few seconds.
¶To disconnect the player from the power
supply completely, remove the AC power
plug from the wall socket.
pg 01-28/C220/22-Eng 12/7/00, 1:42 PM7

8
English
3139 115 20671
Preparations
AM ANTENNA
AUX IN
R
+
–
L
–
+
AUDIO OUT
LR
AC
MAINS
~
FM AERIAL
75Ω
B
C
D
E
Rear Connections
AM Loop Antenna Connection
Connect the supplied loop antenna to the AM
ANTENNA terminal. Place the AM loop antenna
far away from the system and adjust its position
for the best reception.
BFM Wire Antenna Connection
Connect the supplied FM wire antenna to the
FM AERIAL (FM ANTENNA) 75 Ωterminal.
Adjust the position of the FM antenna for the
best reception.
Outdoor Antenna
For better FM stereo reception, connect an
outdoor FM antenna to the FM AERIAL (FM
ANTENNA) 75 Ωterminal using a 75 Ωcoaxial
wire.
FM ANTENNA 75Ω
FM AERIAL 75Ω
OR
CSpeakers Connection
¶Connect the right speaker to Front terminal R,
with the colored wire to +and the black wire
to -.
¶Connect the left speaker to Front terminal L,
with the colored wire to +and the black wire
to -.
¶Clip the stripped portion of the speaker wire as
shown.
unlock lock
12 mm
CAUTION:
– For optimal sound performance, it is
recommended to use the supplied speakers.
– Do not connect more than one speaker to any
one pair of +/-speaker terminal.
– Do not connect speakers with impedance lower
than the speakers supplied. Please refer to
SPECIFICATION section of this manual.
pg 01-28/C220/22-Eng 12/7/00, 1:43 PM8

9
English
3139 115 20671
Preparation
DConnecting other equipment to your
system
You can connect the audio left and right OUT
terminals of a TV,VCR, Laser Disc player, DVD
player or CD Recorder to the AUX IN terminals
at the rear of the system.
EAC Power Supply
After all other connections have been made,
connect the AC power cord to the system and
to the wall outlet.Inserting batteries into the
Remote Control
Inserting batteries into the
Remote Control
¶Insert the batteries (not supplied) into the
remote control as shown in the battery
compartment (Type R06 or AA).
+ - + -
CAUTION
– Remove batteries if they are exhausted
or not to be used for a long time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances, so
they should be disposed off properly.
Controls (illustrations on page 3)
Controls on the player and
remote control
1STANDBY-ON y
– switches the system to standby/on.
2DBB (DYNAMIC BASS BOOST)
– to switch on bass boost to enhance bass
response or to switch off bass boost.
3DIGITAL SOUND CONTROL PANEL
– to view the desired DSC display.
4DSC (DIGITAL SOUND CONTROL)
– to select the desired sound effect :
OPTIMAL, JAZZ, ROCK or TECHNO.
5PROGRAM
for CD ................. to programme disc tracks.
for TUNER ........ to programme preset radio
stations.
for CLOCK ....... to select 12 or 24 hour in clock
setting mode .
6RECORD
– to start recording on tape deck 2.
7DUBBING
– to dub a tape in normal speed.
8DISPLAY SCREEN
– to view the current setting of the system.
9CD CHANGER TRAY
0DISC CHANGE
– to change disc(s).
!OPEN•CLOSE
– to open or close the CD changer tray.
@DISC 1 / DISC 2 / DISC 3 (DISC DIRECT
PLAY)
– to select a disc tray for playback.
#SOURCE – to select the following:
CD / (CD 1•2•3)
– to select CD mode.When disc playback is
stopped, press to select disc tray 1, 2 or 3.
TUNER / (BAND)
– to select Tuner mode. When in tuner mode,
press to select the waveband: FM, MW or LW.
TAPE / (TAPE 1• 2)
– to select Tape mode.When tape playback is
stopped, press to select either tape deck 1 or 2.
AUX (VIDEO)
– to select sound from an external source (e.g.TV,
VCR, Laser Disc player, DVD player or CD
Recorder).
pg 01-28/C220/22-Eng 12/7/00, 1:43 PM9

10
English
3139 115 20671
Controls
$MODE SELECTION
SEARCH àá(TUNING àá)
for CD ................. to search backward/forward.
for TUNER ......... to tune to a lower or higher radio
frequency.
forTAPE .............. to rewind or fast forward a tape.
for CLOCK ....... to set the hour (on the system
only) .
STOP•CLEAR Ç
for CD ................. to stop disc playback or to clear
a programme.
for TUNER ........ to stop programming (on the
system only) .
for TAPE .............. to stop playback or recording.
for DEMO ......... to start or stop demonstration
mode (on the system only).
for CLOCK ....... to exit clock setting or cancel
timer (on the system only).
for PLUG & PLAY
................................. to exit plug & play mode and
return to standby mode (on the
system only).
PLAY É/ PAUSE Å
for CD ................. to start or interrupt playback.
for TAPE .............. to start playback.
for PLUG & PLAY
................................. to initiate and star t plug & play
from standby/demo mode (on
the system only).
PREV í/ NEXT ë(PRESET 4 3 )
for CD ................. to skip to the beginning of the
current, previous, or next track.
for TUNER ........ to select a preset station in
memory.
for CLOCK ....... to set the minute (on the system
only) .
%VOLUME
– to increase or decrease the volume.
^n
– to connect headphones.
&DIM
– to select different brightness for the display
screen : DIM 1, DIM 2, DIM 3 or DIM OFF.
*CLOCK•TIMER
– to view the clock, set the clock or set the timer.
(RDS
– to select RDS data in the following order: station
name, program type, radio text and frequency.
NEWS
– to hear news automatically.
3 CD ROTARY CHANGER SYSTEM •
CD REWRITABLE COMPATIBLE •
CD SYNCHRO RECORDING •
2
21 3
TUNERTAPE 1/2CD
SLEEPAUXDIM
DSC DBB
MUTE
REPEAT PAUSE SHUFFLE
Å
CD DIRECT
VOLUME
á
à
ë
í
É
Ç
#
&
@
£
%
$
$
42
≤
$
%
$
∞
§
≥
)AUTO REPLAY
– to select playback mode either in continuous
AUTO PLAY or ONCE only.
¡TAPE DECK 2
™TAPE DECK 1
£REPEAT
– to repeat a disc track, a disc, or all available discs.
≤MUTE
– to switch off the sound temporarily.
∞SHUFFLE
– to play all the available discs and their tracks in
random order.
§SLEEP
– to switch the system to standby mode at a
selected time.
≥B
– to switch the system to standby mode.
Notes for remote control:
– First select the source you wish to control
by pressing one of the source select keys on
the remote control (e.g. CD ,TUNER, etc.).
– Then select the desired function (É, í,
ë, etc.).
pg 01-28/C220/22-Eng 12/7/00, 1:43 PM10