Philips MCM239/12 User manual

MCM239
Quick Start Guide
What’s in the Box?
You should find these items upon opening the box.
Prepare
Install
Enjoy
Step A
Step
Step
B
C
CR2025
2
User Manual
User manual
Remote control with
1 x CR2025 battery
Stand FM wire antenna
1
Quick Start Guide
Quick start guide
Power adaptor
MW antenna
MCM239 QSG_-12-Eng 22/8/07, 15:251

2
Install
Mounting the stand onto the set
1
Rear connections
3
Connect the cable of the left speaker to LEFT (red and black) and the cable
of the right speaker to RIGHT (red and black).
Extend the wire antenna and fit it to FM ANTENNA.
Insert the MW antenna to MW ANTENNA jacks.
Connect the AC power cord to the wall socket.
4
1
Locate the bottom of the main unit and find the slot, then slide the stand
in the slot until it stops, as indicated in the figure.
Tip
– To receive optimal radio reception, put the
main unit and the antennas as far away as
possible from the power adaptor.
MCM239 QSG_-12-Eng 22/8/07, 15:252

SetupSetup
Setting the clock
2
3
4
5
6
In the standby mode, press and hold DISPLAY/CLOCK on the remote control.
➜24 HR or 12 HR appears for the initial clock setting. To select 12-hour clock or
24-hour clock,
1. Press VOLUME +/- once or more.
2. Press DISPLAY/CLOCK to confirm.
➜ The hours digits start flashing.
Hold down or press VOLUME +/- repeatedly to set the hours.
Press DISPLAY/CLOCK to confirm.
Hold down or press VOLUME +/- repeatedly to set the minutes.
Press DISPLAY/CLOCK to confirm.
Enjoy
1
2
3
4
5
Playing discs
With this system, you can play all pre-recorded audio CDs (CDDA), all finalized audio CD-Rs
and CD-RWs, MP3/WMA-CDs (CD-Rs/CD-RWs with MP3/WMA files)
Press SOURCE once or more to select CD (or CD on the remote control).
Press DOOR OPEN to open the CD compartment.
Insert a disc with the printed side facing up. Then close the CD door.
Press ÉÅ to start playback.
To stop playback, press STOPÇ.
Notes for remote control:
– First, select the source you wish to
control by pressing one of the source
select keys on the remote control (CD or
TUNER, for example).
–Then select the desired function
(2;, 4 , ¢ for example).
IMPORTANT!
– Remove the
protective plastic tab
before using the
remote control
1
Press and hold STANDBY-ON/ ECO POWER y to switch the set to Standby mode.
➜The display shows the set time.
➜-- --:-- -- flashes by default if you have not set the clock.
Helpful hints:
- To set the clock automatically by using a time signal which is broadcast
together with the RDS signal, see the User Manual, RDS: Setting the RDS clock.
MCM239 QSG_-12-Eng 22/8/07, 15:253

Tuning to radio stations
1
2
3
1
2
3
Insert the USB device’s USB plug into the socket on the front panel of the main set.
Press SOURCE once or more to select USB (or USB on the remote control)
Press SOURCE once or more to select TUNER (or TUNER on the remote control).
Press and hold PROGRAM until AUTO appears
➜ Available stations are programmed in order of waveband reception strenght: RDS, FM
followed by MW.
Press the ALBUM/ PRESET buttons once or more until the desired preset station is
displayed.
Playing a USB mass storage device
With the Hi-Fi system, you can use USB flash memory (USB 2.0 or USB1.1),
USB flash players (USB 2.0 or USB1.1), memory cards (requires an additional card reader to
work with this Hi-Fi system).
4
Play the USB’s audio files as you do with the albums/tracks on a CD
Enjoy
Press STANDBY-ON/ ECO POWER y to switch off the set
PDCC-JH-0734
2007 CKoninklijie Philips Electronics N.V.
All rights reserved.
http://www.philips.com
Detailed playback features and
additional functions are described in the
accompanied owner's manual.
MCM239 QSG_-12-Eng 22/8/07, 15:254