Philips SJM3152/17 User manual

SJM3152
EN Universal remote and
docking cradle for iPod™ 3
DE Universalfernbedienung und
Dockingstation für iPod™ 27
FR Télécommande universelle et
station d’accueil pour iPod™ 51
NL Universele afstandsbediening
en basisstation voor de iPod™ 75
ES Mando a distancia universal
y estación base para iPod™ 99
IT Telecomando universal e base
de suporte para iPod™ 123
PT Universal remote and
docking cradle for iPod™ 147
www.philips.com/welcome
SV Universalfjärrkontroll och
dockningsstation för iPod™ 171
EL 
 195
PL
Pilot uniwersalny i podstawka
do odtwarzacza iPod™
219

RU 
  243

CS 
iPod™ 267
HU Univerzális távirányító és dokkoló
az iPod™ használatához 291
TR iPod™ için evrensel uzaktan
  315

3
ENGLISH
Table of Contents
1. Important 4
2. Your universal remote and
docking cradle for iPod™ 6
2.1 What’s in the box 7
2.2 What you’ll also need 7
2.3 Universal remote and docking
cradle for iPod™ overview 8
2.4 Main menu overview 8
3. Getting Started 9
3.1 Prepare 9
3.2 Connect 9
3.3 Install 10
4. Using your universal remote and
docking cradle for iPod™ 12
4.1 Using your universal remote for
iPod™ as a controller for your iPod™ 12
4.2 Browsing and playing music from
your iPod™ 12
4.3 Using your universal remote for
iPod™ as a universal remote control 14
4.4 Starting up an activity 15
4.5 Replacing the batteries 15
5. Use more of your universal
remote and docking cradle
for iPod™ 16
5.1 Adding a device 16
5.2 Deleting a device 17
5.3 Fixing a key 17
5.4 Adding a function 18
5.5 Adding an activity 18
5.6 Deleting an activity 19
5.7 About RF Settings 19
5.8 Changing language 20
5.9 Copying volume 20
5.10 Changing display time out 21
5.11 Performing a full reset 21
6. Warranty and service 22
7. Technical data 23
8. Frequently asked questions 24
Table of contents

4
1 Important
Take time to read this manual before you use
your universal remote and docking cradle for
iPod™. It contains important information and
notes regarding operating your universal remote
and docking cradle for iPod™.
© 2008 Philips Consumer Lifestyle.
All rights reserved. Reproduction in whole
or in part is prohibited without the written
consent of the copyright owner.Trademarks
are the property of Koninklijke Philips
Electronics N.V. or their respective owners.
FCC Compliance
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions :
1 This device may not cause harmful
interference ; and
2) This device must accept any
interference received, including interference
that may cause undesired operation.
DNote
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures :
  • Reorientorrelocatethereceiving
antenna.
  • Increasetheseparationbetweenthe
equipment and the receiver.
  • Connecttheequipmenttoanoutleton
a circuit different from that to which the
receiver is connected.
  • Consultthedealeroranexperienced
radio/TV technician for help.
Any unauthorized modification to this
equipment could result in the revocation of
the authorization to operate the equipment.
Industry Canada Statement
This Class B digital apparatus
complies with Canadian ICES-003.
Important

5
ENGLISH
Disposal of your old product:
Your product is designed and manufactured with
high quality materials and components, which
can be recycled and reused.
When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed with normal household waste.
Please inform yourself about the local rules
on separate collection of batteries because
the correct disposal will help prevent negative
consequences for the environmental and human
health.
Your product contains batteries that shall not
be exposed to water or excessive heat. Please
inform yourself about the local rules on separate
collection of batteries because the correct
disposal will help prevent negative consequences
for the environmental and human health.The
mains plug of this products adapter is used as
the disconnect device and shall remain readily
operable
B Warnings
  • Donotexposetheproducttorain
or water.
  • Keepawayfromsunlighttopreventheat
build-up.
  • Donotdisassembleorrepair.
  • Keepawayfromhighvoltagedevices
  • Whenyoureplacethebatteries,donot
mix different brands of batteries or
place zinc carbon batteries in the
remote.This can trigger unpredictable
behavior.
Take the package to your local recycling center.
Important
EC DECLARATION OF CONFORMITY
We, Philips Consumer Lifestyle: BU P&A: Building SFF5
(manufacturer’s name)
P.O. Box 80002, 5600 JB Eindhoven, The Netherlands
(manufacturer’s address)
declare under our responsibility that the product:
Philips SJM3152 -/05 -/12
RF remote control and docking station
(product description)
to which this declaration relates is in conformity
with the following standards:
EN300 400 -2 V1.1.2:2004
EN301 489-17 V1.2.1:2002
EN300 328 V1.6.1:2004
EN50371:2000
EN60950-1:2001 + A11:2004
(title and/or number and date or issue of the standards)
following the provisions of 1999/5/EC (R&TTE Directive)
and is produced by a manufacturing organisation
on ISO 9000 level.
AQ95-56F-1115KR
(report No.)
Eindhoven, 21/10/2008
(place, date)
K. Rysman
Approbation manager
(signature, name and function)
(name) (type or model)

6
2 Your universal remote and
docking cradle for iPod™
Congratulations on your purchase and welcome
to Philips!
To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome.
Your universal remote and docking cradle for
iPod™ allows you to control your iPod™
remotely while simultaneously charging your
iPod™. It also allows you to control up to 6
other AV devices. Philips offers an entire line of
products to enhance your iPod™ experience.
Your universal remote and docking cradle for
iPod™ works with all iPod™ models that have
a dock connector. For the best connection, use
the dock adapter that came packaged with your
iPod™ or choose the appropriate adapter from
the 5 included with your universal remote and
docking cradle for iPod™.
D Note
Philips SJM3152 is compatible with the following
iPod models:
iPod touch
8GB 16GB 32GB
D Note
Stereo and A/V equipment can only be
controlled via Infra Red, or “line of sight”
operation. Distance for controlling these devices
is limited to 30 feet and the remote must be
in the line of sight of the IR port on your AV
equipment. Only devices with an IR sensor can
be controlled by the remote.
This section gives you an overview of the
controls and functions of this universal remote
with docking cradle for iPod™.
Product highlights
• ControlsiPod™,TV,VCR,DVDplayer,
cable and satellite system
• ControlyouriPod™andhome
entertainment system.
• BacklitLCDscreen
• ProvidesaneasyviewofiPod™menu,
playlists and libraries, even under darker
lighting conditions.
• PlayyouriPod™throughyourhome
entertainment system
• LeaveyouriPod™inthedock,then
connect to home stereo via the AV cable
provided.
• ControliPod™throughwalls,oors,
doors, ceilings and windows with 2-way RF
technology.
• ProvidescontroloveriPod™menu,
features, playlists and libraries from
virtually anywhere at home.
• Dockingcradle
• AllowsyoutoplayandchargeiPod™
simultaneously.
• Shareyourvideolibraryonalargerscreen
• S-VideooutcableoryellowRCAofAV
cable allows you to easily connect to a TV.
Your universal remote and docking cradle for IPod™

7
ENGLISH
2.1 What’s in the box.
Universal remote control Docking cradle for iPod™ Power adapter
S -Video cable 3.5mm-to-RCA AV cable CD ROM with Quick Start guide
instruction manual
(3) AA batteries
*For newer iPod™ versions, please use the adapter that shipped with your iPod™.
2.2 What you’ll also need.
or
iPod™ with Stereo receiver TV Electric outlet
dock connector
Your universal remote and docking cradle for IPod™
5 iPod™ dock adapters: *
•type3formini
•type4for4G20GB
•type5for4G40GB
•type6foriPod™withcolordisplay
 20GB/30GB
•type7foriPod™withcolordisplay60G
AC
AC

8
2.3 Universal remote and docking
cradle for iPod™ overview
Cradle:
1. LED Indicator
2. Slots for removing dock adapter
3. 3.5mm A/V Out Jack
4. DC Power Jack
5. S-Video Out Jack
6. iPod™connector
Remote:
1. Power key
2. LCD Screen
3. Mode key
4. Cursor keys ( Navigation) and OK key
5. Mute key
6. Volume Up/Down key
7. iPod™ Launch key
8. Playback keys
(Play, Rec, Stop, Rew, FF, Pause, Skip, Next)
9. Device specific keys
(Guide,LiveTV,HDD,Menu)
10. Digit keys
11. Device specific keys (CC/Text, Clear,
Enter, Zoom/16:9,Title, Chapter, SUBT,
CC & Zoom for /27 Text & 16:9
for /10, Audio)
12. Channel Up/Down key
13. MainVolume Key
14. Battery low icon (See below)
15. No connection icon (See below)
16. IR Transmission icon (See below)
2.4 Main menu overview
1
62
3
4
5
123
456
789
*0 #
OK
MAIN
VOL MODE
POWER
1
2
3
4
13
5
612
7
8
9
10
11
Universal remote and Docking cradle for IPod™ overview
14
15
16

9
ENGLISH
3 Getting Started
B Warning
Carefully read the safety precautions in section
1.1 Important, before connecting your
universal remote and docking cradle for iPod™.
This section helps you with the first time
installation of your universal remote and docking
cradle for iPod™.
3.1 Prepare
1. Remove all package contents
2. Position your dock near your home
entertainment system, stereo or TV.
3. Turn off power on all your home
entertainment components.
4. Locate the nearest electrical wall outlet.
5. Remove the protective screen cover from
your universal remote for iPod™.
6. Remove iPod™ connector protective
cover on the docking cradle.
7. Select the correct dock adapter for your
specific iPod™ model.
8. Insert the correct dock adapter into the
universal well on your docking cradle.
3.2 Connect
For stereo playback:
1. Connect the red and white RCA
connectors on one end of the supplied AV
cable to the Audio In RCA jacks on your
home entertainment system or stereo.
D Note
If you are not using the device with video, or you
plan on connecting to video via the S-Video
connection, leave the yellow RCA connector
end unplugged.
2. Connect the other end of the supplied AV
cable with 3.5mm plug to the jack labeled
“AV” on your docking cradle.
3. Connect one end of the power cord to
an electrical outlet and the other end
to the DC 12V jack on the back of your
docking cradle.
4. Install the 3 supplied AA batteries into the
battery compartment on the remote.
Follow the proper polarity markings in
the compartment.
For video playback:
1. Connect one end of the supplied S -Video
cable to theVideo In jack on your home
entertainment system or TV.
2. Connect the other end of the supplied
S-Video cable to the jack labeled “S-Video”
on your docking cradle. If you are using the
composite video jacks, plug the yellow
RCA plug into the RCA video jack on
your TV.
3. Connect one end of the power cord to an
electrical outlet. Connect the other end
to the DC 12V jack on the back of your
docking cradle.
4. Install the 3 supplied AA batteries into
the battery compartment on the remote.
Follow the proper polarity markings in
the compartment.
GettingStarted

10
RCA Connection
S-Video Connection
3.3 Install
Once you have installed the batteries in the
remote and connected all of the appropriate
cables, you will need to do a quick “pairing” of
the dock with the remote.
D Note
It is recommended to complete the initial set-up,
including the “pairing” sequence before docking
your iPod™ in the docking cradle.
Pairing the dock with the remote for
the first time:
1. Press the POWER Button on the remote.
2. Position the remote within 1m of the
dock for this duration of this procedure.
3. Follow the easy on-screen set-up wizard
screen prompts.
The easy on-screen set up wizard will guide you
through the different steps on the initial set-up
of your universal remote for iPod™.
Initial set-up of your universal remote for
iPod™:
1. Select the language for your instructions
on the remote using the cursor keys.
Press OK.
While pairing the remote to the docking cradle,
position the remote within 1m of the dock for
the duration of the procedure.
D Note
While your iPod™ is docked in the cradle, your
iPod™ screen will show the message below.
This is normal operation.
2. Select “Next” and press OK.
3. Confirm if you want to add other devices,
like your TV or DVD player, by selecting
“Yes”. Press OK. This replaces the devices’
original remote controls with the universal
remote for iPod™.
GettingStarted

11
ENGLISH
4. Select the device and brand of the device
you want to add by using the cursor keys.
Press OK. The remote will search the
database for available code sets.
5. Follow the on-screen instructions to test
the codes.When a working code set is
found, your device is correctly installed.
When the device is correctly installed, the
following screen appears:
If no working code set is found:
•Youcanperformafulldatabasesearchto
find a correct code set.This can take up to
25 minutes.
•Youcanlearncodesfromtheoriginal
remote device.
To add an additional device:
1. Select “Yes”, Press OK.
2. Repeat this process for each
additional device.
3. When you are finished adding devices,
select “No”. Press OK. Exit the wizard.
D Note
You can adjust the settings of your universal
remote for iPod™ anytime after initial install
via the set-up menu. Press the MODE and IPOD™
LAUNCH keys simultaneously for 3 seconds.
The screen will ask you to press and hold the 2
keys for 3 seconds to enter set-up mode.
GettingStarted

12
4. Using your universal remote
and docking cradle
for iPod™
Learn how to operate your universal remote
and docking cradle for iPod™.
4.1 Using the universal remote for
iPod™ as a controller for iPod™
Control your iPod™ menus, playlists, music and
video libraries.
1. Position the correct dock adapter for your
specific iPod™ model in the
docking cradle.
2. Position your iPod™ in the docking cradle
Charging begins automatically.
3. Press the IPOD™ LAUNCH key.
The remote connects to your docked iPod™
and displays your iPod™ menu playlists.
D Note
If the No Connection icon begins blinking in
the upper right-hand corner of the screen,
the universal remote for iPod™ is not able to
connect to the docking cradle for iPod™. See
Section 8Frequently Asked Questions to
solve the problem.
4.2 Browsing and playing music from
your iPod™
The menu on the universal remote for iPod™ is
similar to the menu on your iPod™.
Navigating in iPod™ mode:
1. Scroll to Music, Settings, Now Playing.
Press OK to select.
D Note
If the iPod™ is notVideo capable, theVideo
option will not appear on your screen.
D Note
“Now Playing” is only viewable when a song is
playing.
GettingStarted

13
ENGLISH
2. Press >or OK on the navigation dial to
go to the next screen.
3. Selecting “Music” presents the following
screens:
Playlists
Artists
Albums
Songs
Podcasts
Genres
Composers
Audio Books
a. To select one of the menu items and
go to the next screen, press >or
OK on the navigation dial.
b. Press <to return to the previous
screen or press OK to move to the
next screen.
c. Repeat until you have made your
listening selection.
D Note
While in iPod™ Mode, press <cursor key to
return to the previous screen / Menu item. Press
OK to make a selection and move to the next
screen.
4. Selecting settings will present the
following screens:
Shufe
   ShufeOptionsare:
Off, Songs, and Albums.
Default for this option is
OFF>
Repeat
Repeat Options are:
Off, One, and All.
Default for this option
is OFF>
a. To select one of the menu items and
go to the next screen, press >or OK
on the navigation dial
b. Press <to return to the previous
screen. Press OK to move to the next
screen.
c. Repeat until you have made the
selection you want to use.
5. Selecting “Now Playing” will display the
most recently played song:
a. Press <to return to the
previous screen.
D Note
Your universal remote and dock for iPod™ does
not allow browsing or control of Photo Library
on your iPod™.
Controlling the volume of your docked iPod™
and connected AV devices, such as a home
theater system, stereo system or TV:
1. To adjust the audio output level of the
iPod™ docking cradle, press theVolume
Up orVolume Down keys. A volume bar
will be shown on the remote’s display
screen.
2. If the sound level of playback is still too
loud or too soft, press the MAIN VOL key
to switch to the AV device and change
the master volume.
D Note
Controlling AV devices requires that the
components have an IR receiver and that your
universal remote for iPod™ is within 30 feet of
the component in line of sight.
3. To return to iPod™ control, press the
IPOD™ LAUNCH key.
GettingStarted

14
D Note
The MainVolume works like a short cut key to
switch to either TV or AMP or RECEIVER mode.
If more than one of these devices is installed, the
priority will be:AMP, RECEIVER,TV.
4.3 Using your universal remote for
iPod™ as a universal remote control
You can add up to 6 AV devices and your iPod™
docking cradle, if available, to your universal
remote for iPod™.
1. Press MODE key.The device icon of your
last selected device will appear on the
screen. Repeat MODE press until the
device you want to control appears on the
display screen.
2. Control the device using the hard keys
on your universal remote for iPod™.
They will access the same function as the
corresponding keys of the original remote
of the selected device.
D Note
Music that was started while using the remote as
an iPod™ controller, will continue to play
even when you change Modes.
D Note
Some specific keys that are available on the
original remote will not be available on your
universal remote for iPod™. Check your original
remote for the available functions.
D Note
When you awaken the remote after a time out,
the last device selected before the time out will
be active.
Device specific keys
The device specific keys on your universal
remote for iPod™ can have different functions,
depending on the device you select via the
MODE key.
Below you can find a complete overview of the
functions for all device specific keys listed for
the IPod™ docking cradle,TV, cable/satellite and
your audio set.
CC CLEAR ENTER ZOOM
GUIDE LIVE TV HDD MENU
TITLE CHAPTER SUBT. AUDIO
OK
MAIN
VOL MODE
POWER
1 2 3
TV TUNER CD
DVD VIDEO 1VIDEO 2
-/- - - AV
AUX
4 5 6
7 8 9
*0 #
1 2 3 4
12 13 14 15
8910 11
TV Sat/Cable Audio set
1.Guide Guide Band
2. Exit Return to Live TV Scan
3. - Exit -
4. Menu Menu Menu
5. Digit Keys Digit keys Input Sources
6. -/-- -/-- Surround
7. AV Input TV/SAT input Surround Mode
8. cc/text Favorite RDS
9. - Help Clear
10. PIP Enter Enter
11.Zoom/16:9 Home GEQ
12. Color key Color key Front
13. Color key Color key Center
14. Color key Color key Rear
15. Color key Color key Test
GettingStarted
CC CLEAR ENTER ZOOM
GUIDE LIVE TV HDD MENU
TITLE CHAPTER SUBT. AUDIO
OK
MAIN
VOL MODE
POWER
1 2 3
TV TUNER CD
DVD VIDEO 1VIDEO 2
-/- - - AV
AUX
4 5 6
7 8 9
*0 #
67
5

15
ENGLISH
D Note
Other installed devices use the functions that
are labeled on the remote. Check your original
remote when you are not sure.
To switch back to your iPod™ playlist after
controlling another device with your universal
remote for iPod™, press the IPOD™ LAUNCH
key.
4.4 Starting up an activity
An activity is a sequence of key presses that you
can program. For example, for watching a
DVD you normally would have to:
1. Turn on the TV;
2. Turn on the DVD;
3. Turn on the surround sound system;
4. Select the right input on yourTV and
surround sound system;
5. Press the PLAY key to start the DVD.
By selecting the activity “Watch DVD” on the
universal remote for iPod™, all the actions are
automatically executed in the predefined
sequence.
Starting up an activity:
1. Press MODE key repeatedly until the
activity name appears in the header
of the display screen.
2. Confirm your selection by pressing OK.
The activity will begin immediately.
You can add up to 8 activities to your universal
remote for iPod™. For more information about
adding and deleting activities, see section
5.5, Adding an activity and section
5.6, Deleting an activity.
Selecting extra functions
Devices may have extra functions that are not
covered by the hard keys on your universal
remote for iPod™.You can select these extra
functions in the display.
1. While in any device mode, Press MAIN
VOL key. Extra functions for the selected
device appear in the display screen.
2. To scroll through all the extra functions,
press the cursor up or cursor down key.
3. When you find the selection you want,
press OK.The remote sends out an
IR signal.
For adding extra functions to your universal
remote for iPod™, see section 5.4,Adding a
function.
E Tip
If you cannot find the extra function you are
looking for, you can exit the Extra menu by
pressing the MAINVOL key again.
D Note
Some devices do not have any extra functions
available in the remote’s data base. However,
you can easily copy additional functions from
your original remote by learning keys. See
section 5.4,Adding a function.
4.5 Replacing the batteries
B Warning
When you replace the batteries, do not mix
different brands of batteries or place zinc carbon
batteries in the remote.This can trigger
unpredictable behavior.
When the batteries are almost empty, the
“Battery Low” icon appears. Replace the
batteries with new LR6 or AA type alkaline
batteries. Follow the local regulations for
disposal of the empty batteries.
GettingStarted

16
5 Use more of your universal
remote and docking cradle
for iPod™
To access the advanced features of your
universal remote and dock for iPod™, you must
use the Set-up menu.
To open the Set-up menu, press and hold the
MODE and IPOD™ LAUNCH keys simultaneously
for 3 seconds.
To exit the Set-up menu and go directly to your
iPod™ menu, press the IPOD™ LAUNCH key
again.
To switch to your last selected device, press the
MODE key.
5.1 Adding a device
To be able to operate your devices with your
universal remote for iPod™, you first have to
add these devices to the remote control.You can
add up to 6 devices from the list of devices
below. Examples of available devices include ( but
are not limited to):
•DVD
•Cable
•DSS(Satellite)
•Tuner
•CD
•TV
Please check the Remote menu for the complete
listing of device labels that can be added.
You cannot add a device twice. Once you have
added a device to your Universal remote for
iPod™, it disappears from the list. However, the
list of devices includes ‘TV-2’ or ‘VCR-2’ for use
when you want to program a second TV or
secondVCR.
To add a device:
1. Select the option “Add a Device” in the
Set-up menu by using the cursor keys
Press OK.
D Note
If you have already added 6 devices on the
remote, besides your iPod™ docking cradle, you
will be asked to delete a device.
2. Select the device and brand you want to
add. Press OK.The remote will search for
available codes for the brand.
3. Follow the on-screen instructions to test
the codes.When a working code set is
found, your device is correctly installed
When the device is correctly installed, the
following screen appears:
If no working code set is found:
•Youcanperformafulldatabasesearchto
find a correct code set.This means that
the remote will send out all codes available
in the database until a working code is
found. This can take up to 25 minutes.
•Youcanlearncodesfromtheoriginal
remote device.
When you want to add another device, select
“Yes”. Press OK and repeat steps 2 and 3.
When you have added all your devices, select
“No”. Press OK to return to the Set-up menu.
Use more of your universal remote and docking cradle for iPod

17
ENGLISH
5.2 Deleting a device
You can delete a programmed device from your
universal remote for iPod™.
To delete a device:
1. Select the option “Delete a Device” in
the set-up MENU by using the cursor keys
Press OK.
2. Select the device you want to delete from
the list. Press OK.
3. Confirm you want to delete that device by
selecting “Yes”. Press OK.
The device is now deleted and becomes
available again in the list of devices you
can add.
4. To return to the Set-up menu, select “Exit”.
Press OK.
D Note
Keys of the deleted device that are used
elsewhere, e.g. in an activity or the volume keys
you copied, will be deleted as well. Check the
activities you programmed and volume keys for
your devices and reprogram them, if necessary.
5.3 Fixing a key
If a hard key is not working properly with your
device, you can fix the key by learning it from
your original remote control.Your universal
remote for iPod™ can store up to 200 learned
keys.You can fix all keys on your universal
remote for iPod™ except the MODE key, the
MAINVOL key and IPOD™ LAUNCH key.
To fix a key:
1. Select the option “Fix a Key” in the Set-up
menu by using the cursor keys. Press OK.
2. Select the device for which you want to fix
a key. Press OK.
3. Confirm you have a working original
remote control available to learn from by
selecting “Yes”. Press OK.
D Note
If your universal remote for iPod™ has already
learned 200 keys, a screen will alert you that the
memory is full and automatically return you to
the Set-up menu.You will have to delete a device
with fixed keys to clear memory.
4. Follow the on-screen instructions to fix
the key: Point the 2 remotes towards each
other at a distance of 0.5 - 2 inches
(2-5 cm).
5. Select the hard key or extra function you
want to fix on your universal remote for
iPod™.To select an extra function press
MAINVOL. Select the function with the
Cursor Up or Cursor Down key. Press OK.
6. Press the corresponding key on the
original remote until you see confirmation
on-screen.
After the key is learned and fixed.The following
screen appears:
7. When you would like to fix other keys for
this device, select “Yes”. Press OK.
Repeat step 3.
Use more of your universal remote and docking cradle for iPod

18
When all keys are fixed and you want to return
to the Set-up menu, select “No”. Press OK.
D Note
Fixing a key overwrites the key’s data that was
stored in your universal remote for iPod™.
This means that if this key is used in an activity
this will also change.
5.4 Adding a function
You can add extra functions to your universal
remote for iPod™.
To add a function:
1. Select the option “Add a Function” in the
Set-up menu. Press OK.
2. Select the device you want to add a
function to.
3. Select the label you want to use for the
extra function.
4. Learn the function from your
original remote.
The extra function is added to your universal
remote for iPod™.
To access the extra function:
1. Press the MAINVOL key to access
the Functions menu.
2. Select the function you want by using the
cursor keys. Press OK.
D Note
Extra functions are device-specific.They can only
be selected when in the desired AV device’s
specific mode. For example, if you want to
access a TV function, the remote must be in the
TV mode.
5.5 Adding an activity
An activity consists of several key presses that
will be sent out by your universal remote for
iPod™ when you select the activity.You can
add up to 8 activities. One activity can contain a
maximum of 25 steps.
By default, your universal remote for iPod™
inserts a delay of 0.6 sec between every key
press to make sure your devices are responding
correctly to the signals.
You can overwrite this default delay:
•Ifoneofyourdevicesneedsalongerdelay
before receiving the next IR signal, you can
insert a delay of 1 or 3 seconds. Replacing the
default delay counts as a step in the activity.
•Ifanactivityneedsnodelaybetweenthe
different key presses to simulate a long key
press, you can add the option “no delay”.
For example:When you would like to turn the
volume up during an activity by pressingVOL
Up key four times, you do not need to insert
delays between these 4 key presses. Between
each step you add the option “no delay”.
To add an activity:
1. Select the option “Add an Activity” in
the Set-up menu by using the cursor keys.
Press OK.
D Note
If you already have added 8 activities, you will
be asked to delete an activity. See section 5.6,
Deleting an activity.
2. Select the label from the list of activities
Press OK.
3. Follow the on-screen instructions to
create an activity.
  • Usethecursorkeystoselectthe
device. Press OK. Press the required key
to insert a key press.
  • Decideifyouwanttoaddanadditional
key or key delay, select YES by pressing
OK.
If you do not wish to add an additional
activity, select NO. Press OK.
Use more of your universal remote and docking cradle for iPod

19
ENGLISH
  •Selectthedelayyouwanttoadd.
Press OK. See instructions at the end of
this procedure, “To select the delay you
want”.
Keep in mind that an activity contains a
maximum of 25 steps.
When you have added all key presses and delays,
select “No”. Press OK.The activity is installed on
your universal remote for iPod™.
4. To return to the Set-up menu, select “Exit”.
Press OK.
To select the delay you want:
1. Use the cursor keys to scroll through the
list of possible delays.
2. Press OK on desired delay.You’ll see
confirmation screen.
3. Press YES to add another key or delay.
Press NO to exit activity set-up.
E Tip
Start up the activity by pressing the Mode key
repeatedly until the activity name appears in
the header of the universal remote for iPod™
display screen. Press OK .
5.6 Deleting an activity
To delete an activity from your remote control:
1. Select the option “Delete an Activity” in
the Set-up menu by using the cursor keys
Press OK.
2. Select the activity you want to delete.
Press OK.
3. Confirm you want to delete the activity
by selecting “Yes”. Press OK.The activity is
deleted and becomes available again in the
list of activities you can add.
4. To return to the Set-up menu, select “Exit”
and press OK.
5.7 About RF settings
Show details:
You can check the status of the connection
between the docking cradle and remote:
1. Select the option “RF Settings” in the Set-
up menu by using the cursor keys. Press
OK.
2. Select “Show details.” Press OK The name
of the connected docking cradle and the
strength of the signal appear.
3. To return to the Set-up menu, select
“Next”. Press OK.
D Note
When the details of the RF Settings show “No
Connection”, the remote is unable to connect to
the docking cradle. If this occurs, you must
reconnect to the dock.
Reconnect to dock
When you want to use your universal remote
for iPod™ with another docking cradle, or in
case of technical problems, you will have to pair
the remote to the docking cradle again.
1. Press and release reconnect button at the
bottom of the iPod™ docking cradle
Use more of your universal remote and docking cradle for iPod

20
2. Select the option “RF Settings” in the Set-
up menu by using the cursor keys.
Press OK.
3. Select “Reconnect to Dock”. Press OK.
You are now pairing the remote to the
docking cradle. Be sure to position the
remote within 1m of the dock for the
duration of this procedure.
4. To return to the Set-up menu, select
“Next” and press.
When the details of the RF Settings show
“Cannot connect to dock.Try again”, you must
reconnect to the dock using the following
procedure:
1. Press the RECONNECT button on the
bottom of the dock.After 5 seconds, the
Philipslogoonthedockwillbeginashing.
2. Select “Yes” on remote. Press OK.
Remote and dock will reconnect.When the
process is completed, the screen below will
appear:
3. Select “Next”. Press OK.
5.8 Changing language
You can change the language of the instructions
on your universal remote for iPod™.
Models purchased in North America offer the
following languages:
•English
•Francáis
•Espanol
Models purchased in Europe offer the following
languages:
•English
•Espanol
•Francáis
•Deutsch
•Nederlands
•Italiano
To change the language:
1. Select the option “Change language” in
the Set-up menu by using the cursor keys.
Press OK.
2. Select your preferred language. Press OK.
The Set-up menu appears on the screen in
your preferred language.
5.9 Copying volume
After adding devices, your universal remote for
iPod™ automatically copies theVolume keys
and Mute key, as follows:
•Videodevices,likeDVD,DVDR,VCRand
Satellite box, use theVolume keys of the
TV (provided that you have programmed aTV).
•Audiodevices,likeCD,DMRandTuner,use
theVolume keys of the Amplifier or Receiver
(provided that you have programmed an
Amplifier or Receiver).
When no TV or amplifier is installed, the Volume
keys will not send codes.When the source
device is added later on, theVolume keys will
be automatically updated.You can change which
Volume keys are used. For example, when you
Use more of your universal remote and docking cradle for iPod