Philips VR130/02 User manual

Service Manual
Service
Service
Service
Video Cassette Recorder
VR130/02/07/39/58
Contents
Chapter
Adjustment Procedure
Schematic Diagrams and CBA's
Exploded Views
Mechanical and Electrical Parts Lists
Sec. 1:
Sec. 2: Standard Maintenance
Mechanism Alignment Procedures
Disassembly / Assembly of Mechanism
Deck Exploded Views
Survey of versions:
/02 PAL B/G, VPS/PDC
/07 PAL I, Ireland
/16 PAL B/G, Spain
/39 SECAM L,L' & PAL B/G, I
/58 PAL/SECAM B/G, D/K
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified
be used.
Published by BK 2002 Video Service Department Printed in the Netherlands c Copyright reserved Subject to modification GB 3103 785 22100
For technical data reference is made to the Service Manual of VR530/02/07/16
3103 785 21990.
The present Manual states only the differences.

1-5-3 HC260IB
Press button VCR on the remote control
before doing VCR related functions
on the remote. By pressing button TV it
is possible to navigate some
functions on PHILIPS TV sets.
1 2 3
4 5 6
7 8
0
9
STANDBY/ON
EJECT
MENU STATUS/EXIT CLEAR
RECORD/OTR STILL
P- MUTE
P+
TV
VCR
SYSTEM
Buttons for VCR feature only
To operate the VCR with the remote control.
To eject the cassette.
To delete last entry/Clear programmed
recording (TIMER).
To record the TV channel selected
at this moment or press repeatedly to start a One-
Touch Recording.
To stop the tape (still picture).
To select the programme number. During
normal playback, press to adjust the tracking.
To call up main menu of VCR.
When tape playback is stopped, press to fast
forward the tape at high speed. During playback, press
to fast forward the tape while the picture stay on the
screen. To store or confirm entry in the menu.
MENU
SYSTEM
P-P+
STILL
RECORD/OTR
CLEAR
EJECT
VCR
When tape playback is stoped, press to rewind
the tape at high speed. During playback, press to
rewind the tape while the picture stay on the screen.To
return the cursor in the menu.
To play a tape, select an item in the menu of
VCR.
To stop the tape, select an item in the menu of
VCR.
Buttons with TV feature
To call up additional TV functions.
To switch VCR or Philips TV on or
off, interrupt menu function.
To access or remove the VCR’s on-
screen status display. To exit on-screen menus. Or, to
access or remove a status display or menu of Philips
TV.
Press to select channels at VCR or Philips TV.
To eliminate the TV’s sound. Press again to
restore the volume.
To adjust the TV’s volume.
MUTE
0..9
STATUS/EXIT
STANDBY/ON
TV
Doesn’t
To change the video (colour) system. [ VR130/39, VR130/58 ]
work in these models. [ VR130/02, VR130/07 ]
[ VR130/02, VR130/07, VR130/39, VR130/58 ]

1-5-4 HC260IB
Front of the device
Back of the set
STILL
PROGRAMME
RECORD
PWR. REC
COUNTER RESET
STANDBY/ON
RF OUT
TV
AERIAL
To switch off or on, interrupt a
function.
To select the
programme number. During normal playback, press to
adjust the tracking.
To record the TV channel selected at this
moments.
When tape playback is stopped, press to fast
forward the tape at high speed. During playback, press to
fast forward the tape while the picture stay on the screen.
When tape playback is stopped, press to rewind
the tape at hight speed. During playback, press to
rewind the tape while the picture stay on the screen.
To play a tape.
To stop the tape and eject the cassette.
To stop the tape (still picture).
To reset the counter.
COUNTER RESET
STILL
/
B
RECORD
PROGRAMME-PROGRAMME+
STANDBY/ON
To connect the TV set(programme number).
To connect the aerial cable.
To connect the TV set.
RF OUT
AERIAL
TV

1-6-3 HC260SNA
[ VR130/02, VR130/07, VR130/39, VR130/58 ]
Signal Name Function
8POUT-1 SCART 1 8Pin Output Control
Signal
A-IN-1,2 Audio Signal Input 1, 2
A-OUT-1,2 Audio Signal Output 1, 2
A-MUTE-H Audio Mute Control Signal
(Mute = “H”)
A-PB/REC Normal Audio Play Back/Record
Signal
A-COM Audio Head Common
AE-H Audio Erase Head
AFC Automatic Frequency Control
Signal
AGC IF AGC Control Signal
AL+12V Always +12V with AC Plug
Connected
AL+5V Always +5V with AC Plug
Connected
AMPC CTL AMP Connected Terminal
AMPVcc AMPVcc
AMPVREFIN V-Ref for CTL AMP
AMPVss AMPVss (GND)
AUDIO-SW1 Audio Input/Output Switching
Control Signal 1 (Mono)
AUDIO-SW2 Audio Input/Output Switching
Control Signal 2 (Mono)
AVcc A/D Converter Power Input/
Standard Voltage Input
C C Terminal
C-CONT Capstan Motor Control Signal
C-F/R Capstan Motor FWD/REV Control
Signal (FWD=”L”/REV=”H”)
C-ROTA Color Phase Rotary Changeover
SIgnal
C-SYNC Composite Synchronized Pulse
CLKSEL Clock Select (GND)
COLOR-IN
SECAM or MESECAM Chroma
Video Input Signal at Super
Impose
CTL (+) Playback/Record Control Signal
(+)
CTL (-) Playback/Record Control Signal (-
)
CTLAMPout To Monitor for CTL AMP Output
D-CONT Drum Motor Control Signal
D-FG Drum Motor Rotation Detection
Pulse
D-PG Drum Motor Pulse Generator
D-REC-H Delayed Record Signal
D-V- SYNC Dummy V-sync Output
DRV-CLK LED Clock Driver IC Control Clock
DRV-DATA LED Clock Driver IC Control Data
DRV-STB LED Clock Driver IC Chip Select
Signal
END-S Tape End Position
Detect Signal
FE-H GND Ground for Full Erase Head
FSC-IN
[4.43MHz]
4.43MHz Clock Input
HLF LPF Connected
Terminal (Slicer)
I2C BUS- SCL I2C BUS Control Clock
I2C BUS- SDA I2C BUS Control Data
JK1-8P-OUT SCART 8Pin Output Control
Signal
KEY-1 Key Scan Input Signal 1
KEY-2 Key Scan Input Signal 2
LD-SW Deck Mode Position Detector
Signal
LM-FWD/REV Loading Motor Control Signal
MOD-A Modulator Audio Output Signal
N-A-PB Normal Audio Playback
N-A-REC Normal Audio Recording
OSCIN Clock Input for letter size
OSCOUT Clock Output for letter size
OSDVcc OSDVcc
OSDVss OSDVss
P-DOWN-L Power Voltage Down Detector
Signal
P-ON+44V +44V at Power-On Signal
P-ON+5V +5V at Power-On Signal
P-ON-H Power On Signal at High
PG-DELAY
Video Head Switching Pulse
Signal Adjusted
Voltage
Signal Name Function

1-6-4 HC260SNA
POW-SAF P-ON Power Detection Input
Signal
REC-SAF-SW
Recording Safety SW Detect (With
Record tab="L"/With out Record
tab="H")
REMOCON-IN Remote
Control Sensor
RESET System Reset
Signal (Reset=”L”)
RF-SW Video Head Switching Pulse
RGB-
THROUGH
SCART 2 RGB Through Control
Signal
SC2-IN Input Signal from Pin 8 of SCART2
SECAM-H SECAM Mode at High
ST-S Tape Start Position Detector
Signal
T-REEL Take Up Reel Rotation Signal
TIMER+5V +5V at Timer
TRICK-H Special Playback = “H” in SECAM
Mode
TU-AUDIO Tuner Audio Input Signal
TU-VIDEO Tuner Video Input Signal
TUN-SW1 Tuner System Control Signal
Output
TUN-SW2 Tuner System Control Signal
Output
V-ENV Video Envelope Comparator
Signal
V-IN-1,2 Video Signal Input 1, 2
V-OUT-1,2 Video Signal Output 1, 2
VIDEO-IN Video Signal Input
VIDEO-OUT Video Signal Output
Vss Vss(GND)
X-IN Main Clock Input
X-OUT Main Clock Input
XC-IN Sub Clock
XC-OUT Sub Clock
Signal Name Function

M
M
LOADING
MOTOR
CYLINDER ASSEMBLY CAPSTAN MOTOR
DRUM
MOTOR
PG
SENSOR
CONTROL
HEAD
CL287
5 5CTL(+)
6 6CTL(-)
CL504
AC HEAD ASSEMBLY
CL509
1 1KEY-1
CL508
POWER SW CBA
MAIN CBA
KEY- 2
C-FG
C-CONT
D-FG
D-PG
ST-S
T-REEL
C-F/R
KEY- 1
REMOCON-IN
CTL(+)
RESET
REC-SAF-SW
PG-DELAY
CTL(-)
D-V SYNC
D-REC-H
DAVN-L
RF-SW
C-ROTA
END-S
IC561
(FIP DRIVER)
14
90
89
94
95
76
87
10
4
80
34
78
2
13
15
18
65
20
31
8
7
RS501
REMOTE
SENSOR
LM-FWD/REV
81
D-CONT77
(DECK ASSEMBLY)
Servo/System Control Block Diagram BLOCK DIAGRAMS
T-REEL
Q501
Q562
Q563
Q564
Q565
DRV-DATA
DRV-STB
DRV-CLK
FP561
FIP
RESET
Q503
SW-POINT
AL+5V
VR501
TIMER+5V
TP506
I2C-BUS SDA
I2C-BUS SDA
I2C-BUS SCL
A-MUTE-H
A-MUTE-H
V-ENV
6
P-ON-H
C-POW-SW
P-ON-H
C-POW-SW
P-DOWN-L 67
66
86 P-DOWN-L
C-SYNC
58
SW506
REC-SAFETY
TO
VIDEO BLOCK
TO
AUDIO BLOCK
2 2KEY-2
4 4KEY-1
KEY SWITCH
KEY SWITCH
CL505 CN651
FUNCTION CBA
1-9-11 1-9-12 HC260BLS
SDA
SDA
SCL
SCL
TU701(TUNER UNIT)
IC503 (MEMORY)
72
83
I2C-BUS SCL
D-V SYNC
D-REC-H
DAVN-L
RF-SW
C-ROTA
I2C-BUS SDA
V-ENV
C-SYNC
I2C-BUS SCL 71
3
5
SDA
SCL
12
11
CAS-LED
TIMER-LED
REC-LED
G1
G2
G3
G4
G5
G6
S1
S2
S7
S8
S9
S10
26
25
24
POWER-LED 23
D565 REC
D564 TIMER
D563 CAS
D562 POWER
D561 STAND-BY
+5V
LD-SW9
AL+12V
AL+12V
AL+5V
AL+5V
SW507
P-ON+5V
LD-SW
AL+5V
D502
S-LED
END-S
TO
POWER
SUPPLY
BLOCK
KEY
SWITCH
TP507
S-INH
SW505
CH-UP
M
CAPSTAN
MOTOR
" " = SMD
NOTE FOR WIRE CONNECTORS:
1. PREFIX SYMBOL "CN" MEANS CONNECTOR.
(CAN DISCONNECT AND RECONNECT.)
2. PREFIX SYMBOL "CL" MEANS WIRE-SOLDER
HOLES OF THE PCB.
(WIRE IS SOLDERED DIRECTLY.)
TEST POINT INFORMATION
:INDICATES A TEST POINT WITH A JUMPER WIRE ACROSS A HOLE IN THE PCB.
:USED TO INDICATE A TEST POINT WITH A COMPONENT LEAD ON FOIL SIDE.
:USED TO INDICATE A TEST POINT WITH NO TEST PIN.
:USED TO INDICATE A TEST POINT WITH A TEST PIN.
23
22
21
2
22
1
20
13
14
16
17
19
18
7
8
IC561
(FIP DRIVER)
IC501
(SERVO/SYSTEM CONTROL)
DRV-DATA
DRV-STB
DRV-CLK
DRV-DATA
DRV-STB
DRV-CLK
FP562
LED CLOCK
G1
G2
G3
G4
S1
S2
S7
S8
S9
S10
23
22
21
28
2
1
68
69
70
20
13
14
16
17
7
8
AUDIO-SW-2 30
AUDIO-SW-1 AUDIO-SW-2
AUDIO-SW-1
29
5
6
CL502
12 C-F/R
11 AL+12V
10 AL+12V
9P-ON+5V
8GND
7C-FG
6C-CONT
5GND
4D-FG
3
LM-FWD/REV
2D-CONT
1D-PG
SENSOR CBA
SENSOR CBA
END-S
ST-S
Q504
Q505
AH
32
33
SECAM-H
TRICK-H
SECAM-H
TRICK-H
AH
Comparison Chart of
Models & Marks
Model Mark
VR130/02
VR130/07
VR130/39
AF
AG
AH
VR130/58 AI
SW510 POWER
CTL97
TP501
CTL

CYLINDER ASSEMBLY
V(R)
V-COM
V(L)
CL253
1
2
3
Video Block Diagram
1-9-13 1-9-14 HC260BLV
(DECK ASSEMBLY)
VIDEO (R)
HEAD
HEAD
AMP
REC FM
AGC
TO SERVO/SYSTEM
CONTROL BLOCK
TO SERVO/SYSTEM
CONTROL BLOCK
C-SYNC
TRICK-H
RF-SW
D-REC-H
C-ROTA
D-V-SYNC
V-ENV
SECAM-H
LUMINANCE
SIGNAL
PROCESS
CHROMINANCE
SIGNAL
PROCESS
PB-H OUT
C-SYNC
V-ENV
D-V-SYNC
RF-SW/C-ROTA
VIDEO (L)
HEAD
TU701
IC301
(Y/C SIGNAL PROCESS)
IC501 (OSD)
REC-VIDEO SIGNAL PB-VIDEO SIGNAL MODE: SP/REC
SERIAL
DECORDER
V-OUT1 1
V-IN1
1
3 3
V-OUT2 1
V-IN2 3
1
3
JACK CBA
IC370 (PAL/SECAM DECTECOTR)
PAL/SECAM
DETECTOR
48
50
52
56
24
6
50
55
52
19
20
JK101
V-OUT1
V-IN1
19
20
JK102
CL151
CL152
CL101
CL102
V-OUT2
V-IN2
61
63
96
95
93
94
CHARA.
INS.
CCD 1H DELAY
BYPASS
MUTE
PB/EE
IN1
TUNER
IN1
TUNER
MUTE
PB/EE
IN2
IN2
AGC
PR
R
Y
C
P
R P R P
Y. DELAY
Y/C
MIX
+
21
7978
AGC VXO
OSD
CHARACTER
MIX COLOR
-IN
FBC
1/2
58 59
65
252928 44
17
14
18
2
16
29
1
28
I2C BUS SDA
I2C BUS SCL
69684643
" " = SMD
NOTE FOR WIRE CONNECTORS:
1. PREFIX SYMBOL "CN" MEANS CONNECTOR.
(CAN DISCONNECT AND RECONNECT.)
2. PREFIX SYMBOL "CL" MEANS WIRE-SOLDER
HOLES OF THE PCB.
(WIRE IS SOLDERED DIRECTLY.)
TEST POINT INFORMATION
:INDICATES A TEST POINT WITH A JUMPER WIRE ACROSS A HOLE IN THE PCB.
:USED TO INDICATE A TEST POINT WITH A COMPONENT LEAD ON FOIL SIDE.
:USED TO INDICATE A TEST POINT WITH NO TEST PIN.
:USED TO INDICATE A TEST POINT WITH A TEST PIN.
67
84
62
70
D-REC-H 80
BUFFER
Q101
BUFFER
Q102
TP751
V-OUT
WF1
TP301
X301
4.43MHz C-PB
WF5
TU-VIDEO
TU-VIDEO
V-IN1TO
SERVO/SYSTEM
CONTROL BLOCK
VIDEO
BUFFER
Q351
MAIN CBA
TP502
RF-SW
WF2
AH,AI
AH
AH
Comparison Chart of
Models & Marks
Model Mark
VR130/02
VR130/07
VR130/39
AF
AG
AH
VR130/58 AI

Audio Block Diagram
REC
AMP
100 3
AUTO
BIAS
2
1
+5V
+5V
Q401
Q406
BIAS
OSC
Q402
Q404
(PB=ON)
Q405
(PB=ON)
Q403
SWITCHING
D-REC-OFF
5EQ
AMP 98
7
LINE
AMP
REC-ON
AUDIO HD-SW
CONTROL
MUTE 11
6
PB-ON
SP/LP-ON
P
R
ALC
DET
ALC
IC301 (AUDIO SIGNAL PROCESS)
4 A-PB/REC
CL504
3 A-COM
1 AE-H
2 AE-H/FE-H
A-PB/REC 4
A-COM 3
AE-H 1
AE-H/FE-H 2
CL287
AUDIO
HEAD
AUDIO
ERASE
HEAD
ACE HEAD ASSEMBLY
FE HEAD
2 FE-H
1 FE-H-GND
CL501
1-9-15 1-9-16 HC260BLA
MAIN CBA
PB-AUDIO SIGNAL REC-AUDIO SIGNAL Mode : SP/REC
71
A-MUTE-H
I2C BUS-SCL
I2C BUS-SDA TO SERVO/SYSTEM
CONTROL BLOCK
FULL
ERASE
HEAD
68 69
SERIAL
DECODER
(DECK ASSEMBLY)
" " = SMD
NOTE FOR WIRE CONNECTORS:
1. PREFIX SYMBOL "CN" MEANS CONNECTOR.
(CAN DISCONNECT AND RECONNECT.)
2. PREFIX SYMBOL "CL" MEANS WIRE-SOLDER
HOLES OF THE PCB.
(WIRE IS SOLDERED DIRECTLY.)
TEST POINT INFORMATION
:INDICATES A TEST POINT WITH A JUMPER WIRE ACROSS A HOLE IN THE PCB.
:USED TO INDICATE A TEST POINT WITH A COMPONENT LEAD ON FOIL SIDE.
:USED TO INDICATE A TEST POINT WITH NO TEST PIN.
:USED TO INDICATE A TEST POINT WITH A TEST PIN.
12
16
INV
ATT
TU701
J911
SW
CTL
IC151 (SWITCHING)
PB/EE
PB/EE
PB/EE
PB/EE
TUNER
TU-AUDIO
AUDIO
IN2
IN1
IN1
AUDIO-SW-1
AUDIO-SW-2 TO SERVO/SYSTEM
CONTROL BLOCK
A-IN1
A-OUT1
8
6
JACK CBA
JK101
A-IN1
A-IN1
3
6
3
6
CN101
A-OUT1
A-OUT1
A-IN2
A-OUT2
8
6
8
6
8
6
JK102
A-IN2
A-IN2
3
6
3
6
CN102
CN151
CN152
A-OUT2
A-OUT2
2
21
1
5
2
4
12
14
15
11
10
9
3
13
TUNER
IN2
IN1
15
13
17
TU701
SW
CTL
IC151 (SWITCHING)
PB/EE
PB/EE
PB/EE
PB/EE
TUNER
TU-AUDIO
IN2
IN1
IN1
AUDIO-SW-1
AUDIO-SW-2 TO SERVO/SYSTEM
CONTROL BLOCK
A-IN1
A-OUT1
8
6
JACK CBA
JK101
A-IN1(R)
A-IN1(L)
2
6
1
3
CL101
A-OUT1(R)
A-OUT1(L)
A-IN2
A-OUT2
8
6
8
6
8
6
JK102
A-IN2(R)
A-IN2(L)
2
6
1
3
CL102
CL151
CL152
A-OUT2(R)
A-OUT2(L)
21
1
5
2
4
12
14
15
11
10
9
3
13
TUNER
IN2
IN1
15
13
17
BUFFER
Q151
BUFFER
Q152
AH
AH
Comparison Chart of
Models & Marks
Model Mark
VR130/02
VR130/07
VR130/39
AF
AG
AH
VR130/58 AI
J984 AF,AG,AI

2
4
16
6
7
Power Supply Block Diagram
CAUTION
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE T1.6AL/250V FUSE.
NOTE :
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F001) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
HC260BLP
1-9-17 1-9-18
COLD
MAIN CBA
HOT CIRCUIT. BE CAREFUL.
HOT
IC001
ERROR
VOLTAGE DET
Q002
Q003
Q001
F001 L003
LINE
FILTER
BRIDGE
RECTIFIER
D001 - D004
1
2
3
4
Q004
(SHUNT REGULATOR)
REG
AC001
T001
P-ON+44V
12
P-ON-H
AL+12V
AL+12V
AL+5V
TIMER+5V
P-ON+5V
P-DOWN-L
AL-5V
Q051
Q054
Q056
Q052
13
15
14
11
17
18
T1.6A L 250V
AH
Comparison Chart of
Models & Marks
Model Mark
VR130/02
VR130/07
VR130/39
AF
AG
AH
VR130/58 AI

1-10-51 1-10-52 1-10-53 HC260SCM1
Main 1/5 Schematic Diagram
THE SAME VOLTAGE FOR
BOTH PLAY & REC MODES.
INDICATES THAT THE VOLTAGE
IS NOT CONSISTENT HERE.
MODE: SP/REC PLAY MODE
REC MODE
123
5.0 5.0
(2.5
~
“ “ = SMD
Comparison Chart of Models and Marks
MODEL MAR MODEL MAR
VR130/02 AF VR130/39 AH
VR130/07 AG VR130/58 AI
MAIN 1/5 Schematic Diagram Parts Location Guide
Ref No. Position Ref No. Position
C501B-1R507C-1
C502 B-1 R509 E-1
C508 E-2 R510 E-2
C510F-2R511E-2
C511 E-2 R513 F-2
C512 E-2 R514 F-2
C513 E-2 R516 E-2
C514 E-2 R517 E-2
C515 E-2 R518 F-3
C516 E-2 R519 F-3
C517 E-4 R520 E-4
C518F-4R521E-4
C519 C-3 R522 E-4
C520B-3R523C-4
C521 B-2 R524 B-4
C522 B-2 R525 B-3
C523 B-2 R526 B-2
C524 B-2 R527 B-2
C526B-2R528C-1
C528 B-2 R529 A-1
C529 B-2 R533 B-3
C530 B-2 R534 A-2
C531 C-1 R535 A-2
C535 B-3 R536 A-2
C538 A-1 R537 A-2
C540 D-4 R538 B-2
C541 B-4 R539 B-2
C561 C-4 R540 B-2
C622 B-3 R541 B-1
C851 E-3 R542 A-3
C852 E-3 R543 A-3
C853 E-3 R544 A-3
C854 E-3 R545 A-2
C855 E-3 R546 A-2
C856 E-3 R547 A-3
C858 E-3 R551 E-3
C859 D-4 R552 E-3
C862E-3R555C-1
R556 C-1
CL501 F-4 R557 C-1
CL502 F-5 R558 C-1
CL504 F-5 R566 D-5
CL505 A-2 R607 D-4
CL508 A-3 R609 D-1
CL509 A-3 R610 D-1
CAPACITORS RESISTORS
CONNECTORS
R613 D-1
D501E-4R619D-1
D502A-1R620D-1
D553 E-2 R851 E-3
R852 E-3
IC501 C-2 R853 E-3
IC503 B-3
IC561 D-5 SW501 A-3
SW502 A-3
L501 B-1 SW504 A-3
L561 B-4 SW505 A-2
L562 B-4 SW506 E-1
L851 E-3 SW507 A-2
L853 D-4 SW510 A-3
Q501 E-2 VR501 B-1
Q503 A-3
Q504 A-2 X501 E-2
Q505 A-1 X502 E-2
Q551 E-3
Q552 E-2 FP562 B-5
RS501 B-2
R501 C-1
R502 C-1 TP501 B-2
R503 C-1 TP502 D-1
R504 C-1 TP506 B-2
R505 C-1 TP507 A-2
R506 C-1 TP508 D-1
TEST POINTS
RESISTORS
TRANSISTORS
DIODES
ICS
MISCELLANEOUS
COILS
SWITCHES
VARIABLE RESISTORS
CRYSTAL OSCILLATORS
IC501 EY VOLTAGE CHART
KEY 1 (7PIN KEY 2 (8 PIN
0.00 ~ 0.51V POWER CH UP
0.51 ~ 0.92V ------------------------ REW
0.92 ~ 1.27V COUNTER RESET PLAY
1.27 ~ 1.61V REC/OTR FF
1.61 ~ 1.98V CH DOWN PAUSE
1.98 ~ 2.39V S-INH ------------------------
2.39 ~ 2.90V ------------------------ STOP/EJECT
2.90 ~ 3.60V ------------------------ ------------------------
3.60 ~ 4.30V ------------------------ ------------------------
4.30 ~ 5.00V KEY OFF KEY OFF
Pin No.
Voltage