Phoebe LED Atlas-Mini series User manual

Tel: [phone] Fax: [phone] Web: www.phoebeled.com
Images are for information only. Phoebe LED shall not be held liable for improper operation of the luminaire in circumstances where procedures and
specications have not been followed correctly.
THANK YOU for buying this PHOEBE LED product. To help ensure this luminaire gives complete satisfaction please only use it according to the
following instructions, and then pass the instructions to the appropriate person for retention and future reference.
This instruction sheet is relevant to Phoebe LED Atlas-Mini LED Slimline Floodlights with part codes:
6416, 6423, 6430, 6447, 6454, 6461, 7581, 7598, 10314, 10321, 10338, 10345, 10352, 10369, 10376, 10383
Specications:
Part Codes PIR sensor
tted Wattage Voltage Power Factor IP Rating IK Rating Useful Lumens
Total
Lumens Cable Insulation Ambient Operating Temp
Black White
7581 10314 No 10W
240V
50/60Hz
>0.5
IP66 IK08
760lm 900lm
VDE H05RN-F
3G 1.0mm
Class I -20°C to 40°C
6416 10338 No 20W >0.5 1450lm 1600lm
6430 10352 No 30W >0.9 2200lm 2400lm
6454 10376 No 50W >0.9 3850lm 4200lm
7598 10321 Yes 10W >0.5 760lm 900lm
VDE H05RN-F
4G 1.0mm
6423 10345 Yes 20W >0.5 1450lm 1600lm
6447 10369 Yes 30W >0.9 2200lm 2400lm
6461 10383 Yes 50W >0.9 3850lm 4200lm
Dimensions:
Part Codes Wattage Width (W) Height (H) Depth (D) Depth inc. PIR (D2)
Black White
7581 10314 10W 140mm 126mm 30mm -
6416 10338 20W 201mm 166mm 34mm -
6430 10352 30W 201mm 166mm 34mm -
6454 10376 50W 298mm 226mm 40mm -
7598 10321 10W 140mm 188mm 30mm 51mm
6423 10345 20W 201mm 216mm 34mm 51mm
6447 10369 30W 201mm 216mm 34mm 51mm
6461 10383 50W 298mm 272mm 40mm 55mm
IP66 IK08
BEFORE YOU START
PLEASE READ ALL THE
INSTRUCTIONS CAREFULLY
ONLY ONCE INSTALLATION
IS COMPLETE
Turn power
back on at
the mains
CIRCUIT TESTING
For high voltage circuit insulation
testing disconnect mains input
supply rst
(Do not circuit test using a Megger)
Turn power
off at the
mains
PRIOR TO INSTALLATION
Warning
1. Installation only to be carried out by a qualied electrician
2. Please ensure surface is suitable and capable of holding the lamp weight
3. Do not operate if product is damaged
4. Suitable for use outdoors IP66 rating
5. This product is not suitable for re rated installations
TIME
Settings are on the
Rear of the PIR
Angle Adjustment:
1. Angle oodlight to desired angle
2. Tighten socket head screw to prevent unit from moving
Wiring Instructions:
1. Installation only to be carried out by a qualied electrician
2. 240V mains cable connection should be made with a
suitable IP65 junction box
3. Connect power lead to 240V mains electricity in
accordance with current wiring regulations
(see wiring diograms overleaf)
Fitting:
1. Mark drill points and drill xing holes and hole for power
cable (if required)
2. Align luminaire and x in place surface using bolts/
xtures suitable for chosen surface, the angled bracket
allows access to mounting points without the need to
disassemble the tting
LUXSENS
Operation Instructions (for PIR Sensor Only):
• The monitoring angle is up to 120°
• Depending on the angle of the sensor the monitoring range
has a maximum detection distance of 12m
• Lighting time length can be adjusted from 10 seconds (±3 sec)
turning clockwise up to 8 minutes (±2 min) after detection
• Dusk-til-Dawn detection can be manually adjusted by turning
the LUX dial to allow for light levels/time of year
(for daylight sensor testing turn fully to sun position)
•
Sensitivity of the motion sensor can be changed by adjusting the SENS dial effective range 5m to 12m
H
WD
H
WD
D2
To 240V
Mains
PIR tilt
& Twist
Socket
Head
Screw

Tel: [phone] Fax: [phone] Web: www.phoebeled.com
Images are for information only. Phoebe LED shall not be held liable for improper operation of the luminaire in circumstances where procedures and
specications have not been followed correctly.
Brown = Live
Green/Yellow = Earth
Blue = Neutral
Black = Live-Out
Brown = Live
Green/Yellow = Earth
Blue = Neutral
Black = Live Out
Brown = Live
Green/Yellow = Earth
Blue = Neutral
To 240V Mains
To 240V Mains
LO
Live-Out unused
for single tting
L-OUT black
L-IN brown
N blue
E
yellow/green
AC220-240V
L
N
E
Terminal
Box Terminal Box Terminal Box
Power < 180W
* Max. power load of a sensor is 180W.
L brown
N blue
E
yellow/green
L brown
N blue
E
yellow/green
4 PIN terminal
AC220-240V
L-OUT
L
L
E
N
N
E
L-IN
E
N
3 PIN terminal
AC220-240V
L
L
E
N
N
E
L
N
E
This wiring diagram relevant to Phoebe LED Atlas-Mini LED Slimline
Floodlights with part codes:
6416, 6430, 6454, 7581, 10314, 10338, 10352, 10376
This wiring diagram relevant to Phoebe LED Atlas-Mini LED Slimline Floodlights with part codes:
6416, 6423, 6430, 6447, 6454, 6461, 7581, 7598, 10314, 10321, 10338, 10345, 10352, 10369, 10376, 10383
This wiring diagram relevant to Phoebe LED Atlas-Mini LED Slimline
Floodlights with PIR sensor part codes:
6423, 6447, 6461, 7598, 10321, 10345, 10369, 10383
Single Standard Atlas-Mini Single PIR Sensor Atlas-Mini
Controlling multiple luminaires with one PIR sensor model
WIRING DIOGRAMS