Phoenix Sandia User manual

Sandia Fire Pit Assembly Instructions

Package Includes: Base (3 Tripod Segments), Ash Hammock, Fire Bowl (3 Diamond Segments), Grate, Fire Ring (6 Segments)

Step 1: Assemble the Base: Align segments with Phoenix Bird facing up and Cactus to bottom right

A. Layout Tripod sections aligning large slots to small slots.

B. Hold 2 segments upright with cactus to bottom right of Phoenix Bird from outside view (see Fig. C). Slide large slot down over small slot until firmly

connected at base.

C. Connect third segment using same directions as in “B” until tripod is connected firmly at base.

D. With Teflon side facing up, place each loop of the Ash Hammock over the corners of the Tripod.

Warning: Handle with care. The fire pit is comprised of machined metal parts, some edges may be sharp.

Terms & Conditions: The user of this fire pit accepts full responsibility for any and all injuries and damages associated with the use of this product.

If you are unable to accept this responsibility, please return the unused fire pit to Phoenix Fire Rings for a full refund.

Large slot

Small slot

A B C D

Step 2: Assemble the Fire Bowl: Align small hole to center and Long slot on left when placing each diamond on the Tripod

E. Slide the corner of one Fire Bowl diamond into the corner of the Tripod and align the edges with the Vertex (see Fig. A).

F. With the next Fire Bowl diamond facing the same direction (small hole in middle, long & short outer slots in same clockwise direction), slide the corner

of the second Fire Bowl diamond into the corner of the Tripod and align with the support vertex and the previously installed bowl diamond.

G. Repeat for third section of Fire Bowl.

H. Place the Wood/Charcoal grate on the Fire Bowl, aligning the outer edge with the curved slots in the fire bowl diamonds.

** It is very important the longer slots are all facing the same clockwise direction to ensure fit of Fire Ring in these slots.

E F G

** When disassembling the Fire Bowl after use, simply dump ashes from each segment of the Fire Bowl into Ash Hammock. Then pickup corners of the Ash

Hammock and dump into a garbage can. You can then wipe off the Teflon Ash Hammock with a damp cloth. Use water, if necessary, to ensure that all

embers have been extinguished.

Vertex

Cactus at bottom right of

Phoenix Bird

Step 3: Assemble the Phoenix Fire Ring: Align segments with Phoenix Bird facing up and Cactus to bottom right

A. Hold two fire ring segments so that the Phoenix birds are oriented in the same direction (Phoenix Bird facing up and Cactus to bottom right). Insert

one segment with the metal finger pointing down into the slot on the segment with the finger pointing up. Insert the segment at a 90 degree angle

until the bottom of finger slots are fully seated.

B. Rotate the two segments apart until an angle of approximately 120 degrees is achieved.

C. Insert each segment in the same fashion until all six segments have been attached to form the ring. When connecting the final segment and joint,

lift the downward pointing finger segment onto the upward pointing finger segment.

D. It may be necessary to slightly flex the angle between the final two mating segments inward to completely seat the last joint.

** Disassemble the ring by reversing the assembly procedure.

90o120o

A B C D

Step 4: Place the Fire Ring on Top of the Base

E. Pick up the Fire Ring by grasping two opposite

segments. Place three corners of the hexagonal fire

ring in the slots on the Tripod. At each corner of the

stand the fire ring segments need to be aligned with

the fire bowl slots. The curved bottom of the

segments must align with the short slot and the 90

degree corner must align with the long slot. Work the

fire ring into the slots until a firm seating is achieved.

F. Place wood or charcoal on the grate and enjoy your

campfire!

** Disassemble the Fire Pit by reversing the assembly

procedure.

Terms & Conditions: The user of this fire pit accepts full responsibility for any and all injuries and damages associated with the use of this product.