Phoenix VX3-350-SCW-DAT Manual

VX3-350-SCW-DAT
MASS STORAGE SUBSYSTEM
Technical Information
Copyright Phoenix International 1996. All Rights Reserved
812 W. Southern Avenue, Orange, CA 92865

PREFACE
A number of conventions are used throughout this manual in order to provide clarity and
descriptive accuracy. These include:
1. The use of an 'H' (character) suffix to a number indicates that the number reference is in
hexadecimal notation.
2. The use of a '-' (minus) postfix to a signal name indicates that the signal is either true when the
signal is at a logic 0 level or that the signal initiates actions on a high-to-low signal transition.
DISCLAIMER
The information contained within this document has been carefully checked and is believed to be
entirely reliable and consistent with the product that it describes. However, no responsibility is assumed
for inaccuracies. Nor does Phoenix International assume any liability arising out of the application
or use of any product or circuit described herein. Phoenix International reserves the right to make
changes to any product and product documentation in an effort to improve performance, reliability or
design. Furthermore, the information contained herein is of a proprietary nature and is not to be
reproduced without prior written consent of Phoenix International.
TRADEMARKS
IBM, PC/XT, PC/AT, EGA, CGA, and VGA are registered trademarks of International Business
Machines Corporation. MS-DOS is a registered trademark of Microsoft Corporation. Hercules is a
trademark of Hercules Corporation.
REV 2.1
DATE 7-94

Table of Contents
Chapter 1 Manual Organization and Introduction 1-1
Scope 1-3
Manual Organization 1-3
VX3-350-SCW-DAT Introduction 1-3
Chapter 2 Features and Specifications 2-1
Scope 2-3
Features 2-3
SCSI Interface Description 2-3
VX3-350-SCW-DAT Specifications 2-4
Chapter 3 Configuration, Installation, and Operation 3-1
Scope 3-3
Drive Hardware Configuration 3-3
Tape Hardware Configuration 3-3
Hard Drive Hardware Configuration 3-3
Considerations for Installation 3-3
VMEbus Slot Requirements 3-3
VMEbus Backplane Requirements 3-3
Power Supply Requirements 3-3
Installing the VX3-350-SCW-DAT 3-3
Drive Software Configuration 3-4
Tape Drive Software Configuration 3-4
Hard Drive Software Configuration 3-4
Termination 3-4
Terminator Power Configuration 3-4
DIFFSNS Voltage operation 3-4
Operation 3-4
Chapter 4 Hard Disk Drive Details 4-1
Scope 4-3
Introduction 4-3
Key Features 4-3
Physical Configuration 4-3
Drive Performance 4-3
Read/Write Performance 4-3
Power Requirements 4-4
Physical Characteristics 4-4
Environmental Characteristics 4-4
Reliability 4-4
Shock and Vibration 4-4
Functional Description 4-4
Error Correction 4-4
Option Jumpers 4-4
Power Connectors 4-4
SCSI Interface Connector 4-4

Chapter 5 DAT Drive Details 5-1
Scope 5-3
Introduction 5-3
Key Features 5-3
Physical Configuration 5-3
Drive Performance 5-3
Power Requirements 5-3
Physical Characteristics 5-3
Environmental Characteristics 5-4
Reliability 5-4
Shock 5-4
Functional Description 5-4
Power Connector 5-4
Host Interface Connector 5-4
Chapter 6 Product Support, Service and Warranty 6-1
Scope 6-3
Warranty Statement 6-3
If You Have a Problem 6-3
Product Repairs 6-3
Obtaining an RMA 6-3
Shipping the Product 6-3
Providing a Product Defect Report 6-4
Warranty Repairs 6-4
Non-warranty Repairs 6-4
Product Updates 6-4
Tables
Table 2-2 SCSI Pin Definition 2-3
Table 2-3 P2 Pin Definition 2-5
Figures
Figure 1-1 VX3-350-SCW-DAT Front Panel 1-4
Figure 1-2 VX3-350-SCW-DAT Jumper Configuration 1-5

Chapter 1
Manual Organization
and Introduction

This page intentionally left blank.

Scope
This chapter describes the organization of this manual and gives an overview of the VX3-350-SCW-DAT.
Manual Organization
This manual is organized as follows:
Chapter 1 MANUAL ORGANIZATION AND INTRODUCTION
Contains an overview of the manual organization and provides a brief product description.
Chapter 2 FEATURES AND SPECIFICATIONS
Describes the product features, compatibility, and electrical specifications.
Chapter 3 CONFIGURATION, INSTALLATION AND OPERATION
Provides information on how to configure and install the VX3-350-SCW-DAT.
Chapter 4 SCSI HARD DISK DETAILS
Contains specific details about the hard disk drive used on the VX3-350-SCW-DAT.
Chapter 5 DAT DRIVE DETAILS
Provides specific details about the tape drive used on the VX3-350-SCW-DAT.
Chapter 6 PRODUCT SUPPORT, SERVICE AND WARRANTY
Describes what to do if you have trouble and how we will support you.
VX3-350-SCW-DAT Introduction
The VX3-350-SCW-DAT has been designed to provide a complete disk/tape drive subsystem which is mechanically com-
patible with the VMEbus. It has been designed specifically to interface with VMEbus processors with an embedded SCSI
Host Adapter. Together with the processor, a complete system can be installed in only four standard VMEbus system
slots. The VX3-350-SCW-DAT provides a DAT drive and a hard disk drive within the same module making it very conve-
nient to have fixed and removable data storage. The drives used on board the VX3-350-SCW-DAT were chosen for their
compatibility, ruggedness and reliability.
Manual Organization and Introduction 1-3

Figure 1-1: VX3-350-SCW-DAT Front Panel
VX3-350-SCW-DAT User's Manual1-4
HD
S
C
S
I
2
1 3
0 4
7 6
6
UNIT 0
ID
2
1 3
0 4
7 6
6
UNIT
ID

DAT Drive
Fixed Hard Drive
Figure 1-2: VX3-350-SCW-DAT Jumper Configuration
Manual Organization and Introduction 1--5

Chapter 2
Features and
Specifications