Photron FASTCAM Mini WX50 User manual

F
FA AS ST TC CA AM M M Mi in ni i W WX X5 50 0/ /1 10 00 0

The copyright of this manual is held by PHOTRON LIMITED.
Product specifications and manual contents are subject to change without notice.
PHOTRON LIMITED bears no responsibility for any results by using our products nor by applying this manual to any operations.
WARNING
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
CAUTION:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Use the appropriate parts designated in the manual to prevent EMC interference.

Introduction
Thank you for your purchase of Photron’s high-speed camera system, the “FASTCAM Mini WX50/100”
(referred to below as the system).
This manual contains the operating instructions and warnings necessary for using the system.
Before using the system, please read the entire manual.
If any part of this manual is unclear, contact Photron using thecontact information printed at the back of the
manual.
After you finish reading the manual, store it in a safe place along with the warranty card and refer back to it
when necessary.

Manual Notation
The following icons and symbols are used in the explanations in this manual.
Icon/Symbol
Description
This symbol indicates content that should always be read.
This symbol indicates instructions that should always be
followed when using the software, or things to be careful of
when using the software.
This symbol indicates supplementary items to be aware of
when using the system.
This symbol indicates the location of a reference.
This symbol indicates a space for you to make notes.
""
This symbol is used to indicate the names of items on a
screen, references, dialog names, and connectors.
[ ]
This symbol is used to indicate menu names, and sub-menu
names.

Using the Manual
This section explains the layout of the manual.
Introduction
The introduction explains the manual and safety precautions.
Chapter. 1 Setup
This chapter gives an overview of the system and an explanation of its features.
Chapter. 2 Recordig
This chapter explains operations related to recording
Chapter. 3 Product Specifications
This chapter explains the system’s specifications.
Chapter. 4 Warranty
This chapter explains about the warranty.
Chapter. 5 Contacting Photron
This chapter lists the contact information to use when contacting Photron if the system malfunctions or if
a portion of the manual is unclear.

Using the System Safely and Correctly
In order to prevent injury to yourself and others, and to prevent damage to property, carefully observe the
following safety precautions.
Photron has given its full attention to the safety of this system. However, the extent of damage and injury
potentially caused by ignoring the content of the safety precautions and using the system incorrectly is
explained next. Please pay careful attention to the content of the safety precautions when using the
system.
This symbol indicates actions that carry the risk that a person could receive a
serious injury.
This symbol indicates actions that carry the risk that a person could receive a
moderate injury, or that damage to physical property might occur.
The safety precautions to be observed are explained with the following symbols.
This symbol indicates actions that require caution.
This symbol indicates actions that are prohibited and must be avoided.
This symbol indicates actions that must always be performed.
Caution
Warning

■Do not perform actions that will damage the AC cable or plug.
(Do not damage the cable, modify it, use it near a heater, excessively bend, twist
or pull on it, place heavy objects on it, or bundle it.)
Using the cable when damaged can cause fire, electric shock, or a short circuit.
■Do not use the system in a manner which will exceed the rating of the power
outlet or wiring equipment used.
Exceeding the power rating might cause a fire from excessive heat.
■Do not insert metallic objects inside, or pour liquids such as water on, the system.
Doing so can cause fire, electric shock, or malfunction from short circuit or heat.
■Do not disassemble or modify the system.
There are high voltages inside the system that can cause electric shock.
■Do not plug in or unplug the power cord with wet hands.
Doing so can cause electric shock.
■Make sure the power plug is fully insert into the socket .
Not fully plugging in the power cable can cause fire from electric shock or heat.
■When something is wrong with the system, unplug the power cable immediately.
- When a foreign substance or liquid, such as metal or water, gets inside.
- When the outer case is broken or damaged, such as from a fall.
- When the system produces smoke, a strange smell, or strange sound.
Using the system in these conditions might cause a fire or electric shock.
Warning

■Always unplug the system when cleaning it or when it is unused for a long period
of time. Leaving or storing the system connected to the power source might cause
fire from insulation deterioration or electrical discharge.
■Please consult us in advance when you perform an event by which laser light or direct rays
fall on the image sensor surface.
■Do not set the system in a location where the temperature gets unusually hot.
The trunk and inside of a car can get especially hot in summer.
Doing so can cause the outer case and internal components to deteriorate or cause a fire.
■Do not place the system in a location prone to oily smoke or steam, or in a location with
a lot of humidity or dust.
Oil, moisture, and dust conduct electricity, which can cause a fire or electric shock.
■Ambient temperature 0-40° C, humidity 85% RH or lower, maximum altitude 2,000m
or lower.
In addition, if exceeding these limits, use in a condensation-free environment.
Use in a condition out of the above limits can cause malfunction.
■Do not store the equipment in a location where the temperature goes below -20°C
or higher than 60°C. Also, prevent condensation from forming during shipment
■This device is for indoor use, do not use it outdoors.
Do not use in a location that has dust.
■When shipping, remove the connecting cable and use the original packaging or a
dedicated carrying case.
Do not ship the equipment in an environment where the temperature goes below
-20°C or higher than 60°C. Also, prevent condensation from forming during shipment
Caution

“CE” mark indicates that this product complies with the European requirements for safety,
health, environment and customer protection. “CE” mark equipments are intended for sales
in Europe.
These symbols indicate that this product is not to be disposed of with your household waste,
according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or
your national laws implementing those Directives.
This product should be handed over to a designated collection point, e.g., on an authorized
one-for-one basis when you buy a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE) and batteries and accumulators.
Improper handling of this type of waste could have a possible impact on the environment
and human health due to potentially hazardous substances that are generally associated
with EEE. Your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office,
waste authority, approved scheme or your household waste disposal service or visit
www.photron.com.
(EEA: Norway, Iceland and Liechtenstein)
This product is in conformity with the protection requirements of EU Council Directive
2014/30/EU (Class A) on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Warning: This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate measures.
European Union (and EEA) only

Electro-Static Discharge (ESD) events may cause immediate and unrecoverable damage to the
image sensor. Please read the following instructions and take EXTREME CARE when cleaning the
image sensor surface.
■ALWAYS take appropriate anti-static precautions when cleaning or working near the
Image sensor.
■DO NOT use any form of cleaning equipment using electrostatic or ‘charged fiber’ technology.
■Please discharge any electrostatic build up in your body by touching a grounded metallic
Surface before working near the camera sensor.
■Very gently, use only clean and dry air to remove dust from surface of the image sensor.
■To remove stubborn contamination use the highest grade (e.g. VLSI grade) pure
Isopropyl alcohol (IPA) with optical wipes of ‘clean room’ grade.
■Extreme care must be taken! Gently wipe across the sensor in a single action.
(DO NOT rub to avoid abrasive damage to delicate optical coatings on the glass surface.)
Cleaning of the Image Sensor Surface

Chapter. 1Setup 1
1.1. System Components and Accessories....................................................................2
1.1.1. Components................................................................................................2
1.1.2. Accessories/Options ...................................................................................2
1.1.3. Type ............................................................................................................3
1.2. Part Names..............................................................................................................4
1.2.1. Camera Body..............................................................................................4
1.2.2. Camera Body Part Names..........................................................................5
1.2.3. Interchangeable Lens Mounts.....................................................................6
1.2.4. Status Display LEDs on the Rear of the Camera Body..............................7
1.2.5. Camera IP Address Initialization.................................................................8
1.2.6. Reset to the Factory Default.......................................................................8
1.2.7. Power Supply Connector............................................................................9
1.2.8. Connecting the Gigabit Ethernet Interface to a PC...................................11
1.3. Input / Output Signal Types ...................................................................................12
1.3.1. TRIG SW IN Connector ............................................................................12
1.3.2. IRIG IN Connector ....................................................................................12
1.3.3. INPUT(1,2) Connector ..............................................................................13
1.3.4. OUTPUT (1, 2) Connector ........................................................................14
1.3.5. Synchronization with a variable frequency ...............................................14
1.3.6. IRIG-sync Operation .................................................................................16
1.3.7. Signal Delay..............................................................................................17
1.4. Connecting the system ..........................................................................................19
1.4.1. Minimum Equipment Connection..............................................................19
1.4.2. Connecting the AC Power Supply.............................................................20
1.4.3. Connecting a PC.......................................................................................21
Chapter. 2 Recording 23
2.1. Selecting the Frame Rate/Resolution....................................................................24
2.1.1. Low Frame Rate Mode .............................................................................24
2.2. Selecting the Shutter Speed..................................................................................25
Chapter. 3 Product Specifications 27
3.1. Specifications.........................................................................................................28
3.1.1. Product Specifications ..............................................................................28
3.1.2. Random Reset Delay / Interframe Time ...................................................28
3.1.3. Other Supported Function.........................................................................29
3.1.4. General Specifications..............................................................................29
3.1.5. AC / DC Adaptor .......................................................................................30
3.1.6. Frame Rate and Resolution......................................................................31
3.1.7. Shutter Speed List ....................................................................................37
3.1.8. Recordable Image Count/Resolution........................................................38
3.1.9. Recordable Times/Resolution...................................................................40
3.2. Dimensions............................................................................................................42
3.2.1. Camera Body............................................................................................42

3.2.2. AC Power Supply Unit ..............................................................................44
Chapter. 4 Warranty 45
4.1. About the Warranty................................................................................................46
Chapter. 5 Contacting Photron 47
5.1. Contact Information................................................................................................48

Chapter. 1 Setup
1.1. System Components and Accessories
1.2. Part Names
1.3. Input / Output Signal Types
1.4. Connecting the system

Chapter. 1 Setup
2
1.1. System Components and Accessories
1.1.1. Components
Refer to the attached packing list for this product's standard components and accessories.
This system does not include a lens.
1.1.2. Accessories/Options
The following options are available for the system.
1. Dedicated Carrying Case
2. DAQ option
3. Movie analysis software
4. High-G Brackets (High-G Lens Brackets)
5. M42 Lens Mount
If you want to use the High-G Lens Bracket option, it requires specific C mount lenses (Focal length:
f8, f12.5, f16). Please contact us for details and fixing method.
Lenses, lamps and other kinds of options are available. Please contact our sales representative or
distributors. Please refer to “5.1.Contact Information ”.
High-G Lens Bracket Installation Example

3 FASTCAM Mini WX50/100 Hardware Manual
1.1.3. Type
For the FASTCAM Mini WX50/100 system, there are monochrome and color versions, for each of
these versions, there are 4 GB standard memory capacity type and 8 GB (or 16GB) high capacity
type. When purchasing, it is possible to select from these models according to the application or
your demands.
The Types are listed below.
Max.
Frame Rate
Full Frame
Max.
Frame Rate
Sensor Type
Memo
ry
Type Name
80,000fps
1,080fps
Color
4GB
FASTCAM Mini WX100 type 80KC –4GB
8GB
FASTCAM Mini WX100 type 80KC –8GB
16GB
FASTCAM Mini WX100 type 80KC –16GB
32GB
FASTCAM Mini WX100 type 80KC –32GB
Monochrome
4GB
FASTCAM Mini WX100 type 80KM –4GB
8GB
FASTCAM Mini WX100 type 80KM –8GB
16GB
FASTCAM Mini WX100 type 80KM –16GB
32GB
FASTCAM Mini WX100 type 80KM –32GB
67,500fps
750fps
Color
4GB
FASTCAM Mini WX50 type 67.5KC –4GB
8GB
FASTCAM Mini WX50 type 67.5KC –8GB
16GB
FASTCAM Mini WX50 type 67.5KC –16GB
32GB
FASTCAM Mini WX50 type 67.5KC –32GB
Monochrome
4GB
FASTCAM Mini WX50 type 67.5KM –4GB
8GB
FASTCAM Mini WX50 type 67.5KM –8GB
16GB
FASTCAM Mini WX50 type 67.5KM –16GB
32GB
FASTCAM Mini WX50 type 67.5KM –32GB

Chapter. 1 Setup
4
Apperance
Rear
1.2. Part Names
The system is composed of components including the camera body, AC power supply, and the
"Photron FASTCAM Viewer" control software (referred to below as PFV).
For each of the system components.
- Do not expose to shock.
- Do not use in an area where flammable gas or dust is present.
- Do not place in an unstable location such as on an unstable platform or an incline.
- Do not disassemble or modify.
- Do not expose to liquids such as water.
- Do not subject to excessive force.
1.2.1. Camera Body
The camera body contains IC memory for image recording and has been designed to be able to
record high-speed images uncompressed. The back of the camera body is equipped the Gigabit
Ethernet interface, which permits full camera control and data download possible via connection to a
PC; the input/output connector, which allows external synchronization signals, trigger signals, IRIG
time code.
FASTCAM Mini WX50/100

5 FASTCAM Mini WX50/100 Hardware Manual
REC R E A D Y
RESET
POWER
I R I G I N I N P U T 2
OUTPUT 2
RECSYN C I N
DC22-32V
O U T P U T 1
I N P U T 1
T R IG S W IN
1000BASE-T
SYNCMODE
IRIG
TRIGGER
POWER
IFLINK/TRANS
( D E F : S Y N C I N ) ( D E F : T R I G T T L I N )
( D E F : S Y N C O U T ) ( D E F : T R I G T T L O U T )
G type F Mount
Front
FASTCAM Mini WX50/100
RESET SW
IP address Reset Switch
Status Indicator LEDs
DC22-32V 55VA
Power Supply Connector
GIGABIT ETHER
Gigabit Ethernet
LAN Cable Connector
POWER SW
Power Switch
I/O PORT
I/O Port Connector
Back
1.2.2. Camera Body Part Names

Chapter. 1 Setup
6
1.2.3. Interchangeable Lens Mounts
The lens mount on the system can be changed according to the recording purpose.
There are 2 types of interchangeable lens mounts: “G type F-mount”, “C-mount”.
How to change the lens mount (G type F-mount →C-mount)
1. Remove the four M5 bolts with the hexagonal holes using the hexagonal wrench.
2. Remove the G type F-mount portion as a unit.
3. Install the C-mount unit using the bolts with hexagonal holes in the 90° diagonal holes.
4. After installation, always verify that the unit is not loose and does not rattle.
G type F Mount
（Standard）
C Mount