PhoXi XS User manual

PhoXi 3D Scanner XS
Quick Start Guide

Scope of Delivery
■PhoXi 3D Scanner XS
■Desktop PoE injector (input: 90 ~ 264 VAC, output: 33.6 W, 56 V PoE, IEEE802.3at)
■M12-X (m) RJ45 (m) ethernet cable






Operation of the Scanner
The scanner is operated by the PhoXi Control application. PhoXi Control allows the user to
control the scanner either manually through a graphical user interface or programmatically
through the provided API.
All PhoXi Control resources can be found on the following link:
www.photoneo.com/3d-scanning-software/
Read the complete PhoXi 3D Scanner Manual for more details:
www.photoneo.com/kb/scanner 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 1/8


Scanning Parameters - Model XS
Parameter
Value
Resolution
Up to 3.2 Million 3D points
Scanning range
161 - 205mm
Optimal scanning distance (sweet spot)
181mm
Scanning area (at sweet spot)
118 x 78mm
Point to point distance (at sweet spot)
0.055mm
Calibration accuracy (1σ)
0.035mm
Temporal noise (1σ)
0.03mm
Scanning time
250 - 2000ms
Dimensions
77 x 68 x 296mm
Baseline
85mm
Weight
900g
3D point throughput
16 Million points per second

These parameters are valid at 22°C - 25°C, at focus distance for white objects with 80 % albedo.
 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 2/8

Scanning Volume - Model XS
 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 3/8

Mounting the Scanner

Mounting options:
■Use 4x M4 screws with a metal mounting plate of suitable size - preferred mounting
method for heat dissipation.
■Use a M8 screw.
■Use a 3/8 - 16 UNC screw with a tripod.

⚠ WARNING
Hot surface warning
The surface of the processing unit becomes hot to touch when the device is in use. Mount
the device on a metal mounting plate that will act as a thermal bridge to dissipate the heat
or use the carbon body to manipulate the device.
Installation site restrictions:
■Ensure that mounting construction is rigid enough to avoid vibrations during scanning.
■Allow clearance of 25 mm for natural convection cooling.
■Operating temperature of the scanner is 0 °C to 45 °C.
⌑Operating temperature for optimal scanning performance is 22°C to 25°C.
■Separate the scanner from high-voltage devices and devices generating high electrical
noise.
The complete environment conditions for installation can be found in the full user manual at
www.photoneo.com/kb/scanner 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 4/8

Connecting to the Scanner

Power over ethernet:
■Recommended powering option
■1Gbps ethernet cable to the PoE
injector IN port
■M12-X ethernet cable to the PoE
injector OUT port
24V & GPIO
■Desktop & DIN rail adapters
supported

M12 A Coded - 24V & GPIO Pinout
Pin
Cable Color
Pinout
Function
1
White
DC_IN
+ 24V
2
Brown
OPTO_IN2_GND
*laser interlock ground
3
Green
GND
ground
4
Yellow
OPTO_IN1
-
5
Grey
OPTO_IN1_GND
-
6
Pink
OPTO_OUT
-
7
Blue
OPTO_OUT_GND
-
8
Red
OPTO_IN2
*laser interlock signal
* laser interlock requires special firmware package
 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 5/8

Status LEDs
The LEDs indicate the following states of the scanner:

Supported Network Topologies
 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 6/8

Powering Requirements
Connector
M12 X coded
M12 A coded
PoE Standard
IEEE802.3at
-
Operating voltage Ue DC
min. 55 V
24V (20 - 30V)
Residual ripple maximum (% of Ue)
0.5 %
2%
Rated operating current Ie (Imax)
0.36A (0.6 A)
1A (2A)
Minimum power
33 W
60W
Shielding
Fully Shielded RJ45
-
Transfer data rate
1 Gbit
-
Maximum recommended cable length
20 m
20m*
* for cable length over 10 m please ensure operating voltage at minimum 28 V

Powering Accessories for Custom Cablings
PhoXi 3D Scanners offer several options to connect the device. See the PhoXi 3D Scanner
User Manual for more information.
Photoneo offers a selection of:
■Cables in different configurations of lengths and materials,
■Adapters (desktop, DIN),
■Old PhoXi 3D Scanner cabling compatibility accessories
■Please contact your sales representative for inquiries about the available options.


Warranty
Warranty conditions are stated in General Term and Conditions on Photoneo website:
www.photoneo.com/kb/terms-conditions
 
08/2020 PhoXi 3D Scanner XS - Quick Start Guide 7/8

Safety
PhoXi 3D Scanner Model XS is a laser class 3R device. Class 3R lasers are considered safe
when handled carefully.
Laser class 3R label


⚠ WARNING
Do not deliberately look into the laser beam. This may cause injury to the retina.
Laser protective eyewear is normally not necessary.


Contact Us

Headquarters
Photoneo s.r.o.
Plynarenska 1
82109 Bratislava
Slovakia
Web
www.photoneo.com

Support
[email protected]

Business Inquiries
[email protected]

08/2020 PhoXi 3D Scanner XS - Quick Start Guide 8/8