PICK UP BRICKS PB-2101 User manual

PICK UP BRICKS LLC
14435 Benefit Street • Building 4 • Sherman Oaks, CA USA
[email protected]
PB-2101

WARNING
: Please read this Instruction Manual carefully
before use and keep it handy for future reference.
SAFETY PRECAUTIONS
1. Do not operate the Pickup Bricks toy vacuum without the foam filter installed in the dust collector.
Doing so could cause damage to the vacuum motor that would not be covered under any warranty.
2. The Pickup Bricks toy vacuum is designed for use by Children aged 5 years and above but can be
used safely by anyone over the age of 3.
3. Young children or people with reduced physical, mental, or sensory capabilities should be instructed
in the safe use of the Pickup Bricks toy vacuum before allowing unsupervised operation.
4. The Pickup Bricks toy vacuum is designed for light home use only.
5. When unplugging the power adapter from a wall outlet, only pull from the plug. Do not pull on the
power cord.
6. Do not use outdoors.
7. Do not leave the Pickup Bricks toy vacuum unattended when it is switched on, as this may be a
source of danger.
8. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly
qualified persons in order to avoid a hazard.
9. Do not use the Pickup Bricks toy vacuum to pick up any of the following objects. Doing so will
damage the unit and risk causing injury to both those misusing the vacuum and those in their general
vicinity. Additionally, using the device with any items listed here is a fire hazard.
o Large or sharp objects
o Broken glass
o Batteries or any electronic items
o Liquids of any kind
o Flammable or explosive items
10. Do not use corrosive liquids or strong cleaners to clean the Pickup Bricks toy vacuum, and only
clean the vacuum when it is disconnected from the power adapter and turned off.
11. Check the Pickup Bricks toy vacuum power adapter and cords regularly for visible damage.
12. Never attempt to open the Pickup Bricks motor housing or power adapter or remove or replace the
plug or power cable by yourself. Always have repairs to the Pickup Bricks toy vacuum carried out by
a professional. There is considerable danger to the user if repairs are not performed correctly.
13. Never submerge the Pickup Bricks toy vacuum in water and only operate it if it is thoroughly dry.
14. Only use the Pickup Bricks toy vacuum on dry surfaces.
15. Do not touch the plug or power cable with wet hands.
16. Do not hold the end of the Pickup Bricks suction tube close to people or animals when in operation.
17. Only use the Pickup Bricks with the accessories supplied.
18. The Pickup Bricks toy vacuum must only be charged at the current and voltage specified on the
rating label. Only use the power adaptor that is supplied with the Pickup Bricks to charge the internal
batteries.
19. The Pickup Bricks toy vacuum utilizes internal Li-ion batteries; do not expose the unit to high
temperatures or otherwise attempt to ignite the batteries, as this could cause them to explode.
20. Please keep these instructions in a safe place.
TURN ON/OFF SWITCH OFF (O) BEFORE CHARGING!
INTERNAL BATTERIES WILL NOT RECHARGE WHEN
ORANGE ON/OFF SWITCH IS IN THE ON (|) POSITION

COMPONENTS
1. Handle
2. Clear top cover
3. Brick collector tray
4. Foam filter
5. Dust collector
6. Locking clasp
7. Hose Connection point
8. Main body
9. Front wheel
10. Wheel
11. Hose base
12. Hose
13. Suction tube
14. Power adapter
15. On/Off switch
16. 14.8V DC power input

TECHNICAL DATA
Battery Voltage
Li-ion 14.8V
Battery capacity
2000mAh
Power consumption
100 W
Operating time
15-20mins
Vacuum
above 6.5Kpa
Charge
2-2.5 Hours
Adaptor:
Input 100-240V, 50/60Hz, Output: 17V 800mA
CHARGING
Battery charging should only be performed by adults who
understand the safety precautions.
First turn off Pickup Bricks – it will not recharge with the switch in the on position even if
plugged into the wall. Make sure Pickup Bricks is off by pushing the side of the orange
on/off switch marked with a circle (O = off).
Insert the power adapter into the wall socket and then plug the cable into the Pickup
Bricks toy vacuum. The color of the light on the adapter will be red once the power
adaptor is connected to both the wall socket and the Pickup Bricks toy vacuum.
Remember, it will only charge if the on/off switch is turned off.
It takes approximately 2.5 hours to fully charge the battery before the first use. The light
on the power adapter will turn green when Pickup Bricks is fully charged (as long as the
on/off switch is turned off).
The adapter may become warm during charging - this is normal.
TURN ON/OFF SWITCH OFF
(O) BEFORE CHARGING

OPERATING INSTRUCTIONS
NOTE: Before using Pickup Bricks, read the instruction book carefully.
Step 1:
First, attach the wheels to the main body
by lining up the circular section sticking
out of the back of each wheel with the
round opening in the wheel well on either
side of the main body, and snap into
place.
Step 2:
Next, attach the hose connector to the
hose by fitting it over the end of the hose
with the shorter fitting. Slide the end of
the connector with the rectangular
cutouts over the hose fitting until you
hear a snap.
Step 3:
Insert the foam filter into the dust
collector, then insert the dust collector
into the main body as shown.

Step 4:
Insert the brick collector tray onto the dust collector.
Step 5:
Place the clear top cover onto the main body,
then fasten the lock clasps on both sides.
Step 6:
Insert the hose connector into the hose base
then rotate the hose connector to fasten the hose
connector to the hose base.
Step 7:
Turn the orange on/off switch on to start suction. |= on.
Bring the end of the suction tube closer to the building blocks until they are picked up by
Pickup Bricks’ suction.

EMPTYING & CLEANING
Step 1:
Release the lock clasps on both sides and remove the top cover.
Step 2:
Empty the bricks from the brick collector tray by pouring them into a storage container.

Step 3:
After every 3rd or 4th use, clean out the collected debris.
Remove the brick collector tray, then take out the dust collector. Pour the debris from the
dust collector into a trash can.
For further cleaning, remove the foam filter from the dust collector.
Wash the filter under flowing water. Dry it in air naturally before replacing it back in the
dust collector, making sure the filter is dry before replacing it.
Step 4:
Re-install the components:
First replace the foam filter back into the dust collector, then replace the dust collector,
the brick collector tray, and the top cover.
WARNING
Do not operate Pickup Bricks
without the foam filter in place.