PICO PRO4Q User manual

XDS-PRO Satellite Receivers
User’s Guide
XDS-PRO SERIES (PRO4Q, PRO1Q)
Visit Our Website www.picodigital.com
Contact Us 858.546.5050
Toll Free 858.421.6511
Please Read this guide thoroughly before use. Keep this guide handy for future reference.

XDS-PRO Satellite Receivers
2
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
Copyright © 2011 X-Digital Systems, Inc.
All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including but not limited to photocopying, recording, or by any information storage and
retrieval system without the prior written permission from X-Digital Systems, Inc.
Warning and Disclaimer
This document is intended to XDS-PRO4Q and PRO1Q DVB
Satellite Receivers Every effort has been made to make this document as complete and accurate as possible, but
no warranty or fitness is implied. The information is provide-Digital Systems shall have
neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the
information contained in this document.
Acknowledge of Trademarks
Any product or corporate names used herein may be trademarks or registered trademarks, and are only used for
identification and explanation, without intent to infringe. Any terms mentioned or used that are known trademarks or
service marks have been appropriately capitalized and italicized. X-Digital Systems, Inc. cannot attest to the
accuracy of this information. Use of a term in this manual should not be regarded as affecting the validity of any
trademark or service mark.
Printed in the United States of America
X-Digital Systems, Inc.
6260 Sequence Drive
San Diego, CA 92121
Patent Pending
X-Digital Systems, Inc., DVB Satellite Receiver Patents Pending
Document Revision History
Revision
Date
Description
ECO#
A
10/11/11
Initial release for PRO1Q and PRO4Q models, Firmware v0.0.6
1514

XDS-PRO Satellite Receivers
3
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
TABLE OF CONTENTS
1 INTRODUCTION..................................................................................................................................6
1.1 Important Information....................................................................................................................6
1.2 Hardware Upgradeability...............................................................................................................6
1.3 Hardware Versatility......................................................................................................................6
1.4 Network Management System......................................................................................................7
2 GETTING STARTED............................................................................................................................8
2.1 Unpacking the Receiver................................................................................................................8
2.2 Safety Precautions........................................................................................................................8
2.2.1 Excessive Temperature ........................................................................................................8
2.2.2 Proper Ventilation..................................................................................................................8
2.2.3 Heat, Humidity, and Dust ......................................................................................................9
2.2.4 Power Cord Cabling..............................................................................................................9
2.2.5 Reliable Earthing...................................................................................................................9
2.2.6 Circuit Overloading................................................................................................................9
2.2.7 Foreign Objects.....................................................................................................................9
2.3 Physical Installation of the Receiver ...........................................................................................10
2.3.1 Rack Mounting the Receiver...............................................................................................10
2.3.2 Uneven Loading of Rack.....................................................................................................10
2.4 Connecting the Receiver to a Satellite Dish................................................................................10
2.4.1 Outdoor Antenna Grounding...............................................................................................10
2.4.2 DC Voltage Requirement ....................................................................................................11
2.4.3 Warnings About Shorting DC..............................................................................................11
2.5 Connecting to the Ethernet Network...........................................................................................12
2.5.1 Connecting the Cables........................................................................................................12
2.5.2 Using DHCP or Static IP Addresses...................................................................................12
2.5.3 Assigning a TCP/IP Address...............................................................................................12
2.5.4 Assigning a Subnet Mask....................................................................................................12
2.5.5 Assigning a Default Gateway..............................................................................................12
2.5.6 Proxy Server Configuration.................................................................................................13
2.5.7 DNS Server Configuration...................................................................................................13
2.6 Connecting the Audio Ports ........................................................................................................13
2.6.1 Analog Audio Ports..............................................................................................................13
2.6.2 Digital Audio Port.................................................................................................................13
2.7 Connecting the Relay Ports ........................................................................................................13
2.7.1 Physical Ports......................................................................................................................13

XDS-PRO Satellite Receivers
4
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
2.7.2 Cues....................................................................................................................................14
2.8 Connecting the Program Associated Data (PAD) Port ...............................................................14
2.8.1 In-Band Ancillary Data ........................................................................................................14
2.8.2 Out-of-Band Ancillary Data .................................................................................................14
3 FRONT PANEL OPERATIONS..........................................................................................................14
3.1 Status LEDs ................................................................................................................................14
3.1.1 Power LED..........................................................................................................................15
3.1.2 Signal LED ..........................................................................................................................15
3.1.3 Update LED.........................................................................................................................15
3.1.4 Fault LED ............................................................................................................................15
3.2 LCD Display and User Interface..................................................................................................15
Main Menu Options ............................................................................................................................15
3.2.1 Status Sub-Menus...............................................................................................................16
3.2.2 SETUP Sub-Menus.............................................................................................................17
3.2.2.1 SETUP: NETWORK Sub-Menus ................................................................................19
3.2.3 AUDIO PORTS Sub-Menus................................................................................................20
3.2.3.1 AUDIO PORTS:SETUP Sub-Menus...........................................................................20
4 RECEIVER WEB INTERFACE ..........................................................................................................22
4.1 General Menu..............................................................................................................................23
4.1.1 Status Tab...........................................................................................................................23
4.1.2 Tuner Tab............................................................................................................................24
4.1.3 Setup Tab............................................................................................................................25
4.1.4 Relays Tab..........................................................................................................................26
4.1.5 Opto Inputs Tab...................................................................................................................27
4.1.5.1 Coded Opto Input Mode..............................................................................................27
4.1.5.2 Uncoded Opto Input Mode..........................................................................................28
4.1.5.3 Programming Opto Inputs...........................................................................................29
4.1.6 Logs Tab .............................................................................................................................30
4.2 Programming Menu.....................................................................................................................31
4.2.1 Programs Tab......................................................................................................................31
4.2.2 Recordings Tab...................................................................................................................31
4.3 Content Menu..............................................................................................................................31
4.3.1 Audio Tab............................................................................................................................32
4.3.2 Traffic Tab...........................................................................................................................32
4.3.3 All Tab .................................................................................................................................32
5 AFFILIATE WEB INTERFACE...........................................................................................................33
5.1 Accessing and Logging In...........................................................................................................33

XDS-PRO Satellite Receivers
5
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
5.2 Play Scheduling ..........................................................................................................................34
5.3 Changing the Relay Mappings....................................................................................................40
5.4 Checking Receiver Health...........................................................................................................41
5.5 Documentation Repository..........................................................................................................42
5.6 ...........................................................................................42
6 MONITOR AND CONTROL INTERFACE..........................................................................................43
6.1 Setting up a Console Connection................................................................................................43
6.2 Console Commands....................................................................................................................43
7 XDS DISCOVERY TOOL...................................................................................................................54
7.1 About The XDS Discovery Tool ..................................................................................................54
7.2 Using the XDS Discovery Tool....................................................................................................55
7.3 Troubleshooting the XDS Discovery Tool...................................................................................55
8 SPECIFICATIONS..............................................................................................................................56
8.1 Receiver Monitor & Control and Interface Specification .............................................................56
8.1.1 M&C Interface Features......................................................................................................56
8.1.2 M&C Interface Connector Pin-Outs.....................................................................................56
8.1.3 Relay Outputs......................................................................................................................57
8.1.4 Analog Audio Output...........................................................................................................58
8.1.5 Analog Audio Input..............................................................................................................60
8.1.6 Digital Audio Input...............................................................................................................61
8.1.7 Digital Audio Output ............................................................................................................62
8.1.8 PAD/ASYNC Output Port....................................................................................................63
8.2 Ethernet Port...............................................................................................................................64
8.3 RF Input Parameters...................................................................................................................64
8.4 Mechanical and Electrical ...........................................................................................................65
8.5 Environmental .............................................................................................................................65
8.6 Regulatory Compliance...............................................................................................................66

XDS-PRO Satellite Receivers
6
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
1 INTRODUCTION
Welcome to the future of digital audio for the radio industry. This is your user guide to our line of X-Digital
PRO receivers. These receivers are equipped to deliver multiple audio services in high quality digital
audio for your radio station. It has been designed to make use of all the digital communication features of
today, and to be upgraded to take advantage of the technologies of tomorrow.
1.1 Important Information
Throughout this guide, you will find icons designed to help you quickly spot important information:
Note!
The note icon identifies information for the proper
operation of your equipment, including helpful hints,
shortcuts, or important reminders
Caution!
The caution icon identifies information that requires
careful attention in order to prevent equipment damage.
Warning!
The warning icon identifies a procedure or practice that
could result in personal injury if not performed correctly.
1.2 Hardware Upgradeability
X-Digital Systems, Inc. can upgrade its main control software and audio decoder algorithms over-the-air.
This ensures that your receiver will always have the most up to the minute features and functionality.
1.3 Hardware Versatility
The PRO1Q can deliver one channel of audio received via satellite on its single output port while the
PRO4Q can deliver up to four channels of audio on any one of its four balanced output ports. Additionally,
content can be received and stored locally for later use. This content can originate from a real time
satellite broadcast, from a high speed satellite IP distribution channel, or can be retrieved via the Internet
over the Ethernet port.

XDS-PRO Satellite Receivers
7
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
1.4 Network Management System
The XDS-PRO satellite receivers have been specifically designed so that its output can be controlled via
one central web application. This application is called the Network Management System, or NMS. From
the NMS, the receiver can be monitored and managed, and the user can set a schedule of live and
delayed programs for each output port. The NMS will also coordinate file transfers to store sound, data,
or hardware updates directly to the PRO  internal storage device. The NMS will also come
equipped with an advanced event logging system ensuring that any technical problems will be
accompanied by a full history so that causes of problems may be easily identified and eliminated.

XDS-PRO Satellite Receivers
8
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
2 GETTING STARTED

are in a hurry, there is a Quick Start guide that comes packaged with the receiver, but please be sure to
consult this section at your earliest convenience.
2.1 Unpacking the Receiver
Upon receiving your XDS-PRO receiver, ensure that all of the necessary parts have been included.
2.1.1 List of Contents
Below is a table that lists the contents that are packaged with the PRO4Q and PRO1Q.
Item
Quantity
Receiver
1
Power Cord
1
Quick Start Guide
1
Installation Kit (Optional)
1
Network Data Sheet
1
2.2 Safety Precautions
Caution!
The following sections provide a list of general hazards to be
avoided for safe, reliable use of the PRO receivers.
For the complete French translation of this section, please refer to
the Safety Precautions French addendum.
2.2.1 Excessive Temperature
The XDS-PRO receivers have been designed to operate safely and reliably in an ambient temperature of
0° to 50° C. We expect the system to operate without a need for a fan in air conditioned locations. The fan
will be electronically controlled via temperature sensor. This will allow the unit to operate under less than
optimal conditions. However, once the receiver is located in a closed or rack environment, the ambient
temperature may be greater than room temperature. Please take this into consideration when installing
the receiver, making sure that the ambient temperature around the receiver does not exceed the
temperature range 0°to 50° C.
2.2.2 Proper Ventilation
Air vents on the side and rear of the receiver are provided to ensure proper air flow through the receiver
unit. In order to ensure proper operation, the XDS-PRO receivers should be located such that its
ventilation is not impeded. In a rack environment, at least two inches on the sides and at least 5 inches in

XDS-PRO Satellite Receivers
9
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
the rear should be provided. Proper ventilation will help ensure the receiver performs both safely and
efficiently.
2.2.3 Heat, Humidity, and Dust
In order to avoid unnecessary internal damage, avoid placing the receiver next to external heat sources
such as heaters, direct sunlight, heating ducts, etc. Also avoid locations of high humidity, dust, and
vibration.
2.2.4 Power Cord Cabling
Avoid running the power cord across places of high traffic where it can be crimped or tripped over. Make
sure the cords are securely fastened to both the wall outlet or power strip, and the back of the receiver.
Do not place objects on or leaning against power cords.
2.2.5 Reliable Earthing
Proper mains earth grounding of the electronic rack system and rack mounted equipment should be
maintained. To ensure proper and reliable grounding of the XDS-PRO Receiver, the electronic rack
system shall employ either permanently wired mains connection or use pluggable equipment type B type
wiring in a restricted access location with proper equipotential bonding applied. The XDS-PRO Receiver
includes a rear panel grounding stud for connection to the electronic rack ground rails.
The XDS-PRO Receiver must be connected to an earthed mains socket-outlet.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
Warning!
Make sure all rack mounted equipment and the electronic rack
system is properly grounded.
2.2.6 Circuit Overloading
The XDS-PRO receiver can draw up to 1.5 Amps at 120VAC as indicated on the back of the receiver.
When adding the receiver to an already existing rack setup, take care to ensure the maximum current
rating of the circuit is not exceeded.
2.2.7 Foreign Objects
Warning!
Inserting any type of foreign object into the ventilation holes of the
receiver can result in shock or serious injury of the operator.
If a foreign object is inserted into the receiver, immediately power down the receiver and contact X-Digital
Systems technical suppo

XDS-PRO Satellite Receivers
10
R830001-2001, REV. A
www.picodigital.com
TOLL FREE 800.421.6511
2.3 Physical Installation of the Receiver
The following section will guide you through the physical installation of the XDS-PRO receiver.
2.3.1 Rack Mounting the Receiver
The XDS-PRO receiver has been specifically designed for installation and operation in an EIA standard
19-inch equipment rack. When mounting it in the rack, use pan or round head screws and flat washers in
all four front panel mounting locations.
Caution!
Do not paint mounting ears as it hinders the grounding path from
the receiver to the rack.
2.3.2 Uneven Loading of Rack
When installing the XDS-PRO receiver in a free standing or unsecured rack, make sure to place heavier
pieces of equipment on the bottom and lighter pieces on the top.
Caution!
Uneven loading may cause the rack to be unstable and
hazardous.
2.4 Connecting the Receiver to a Satellite Dish
This section contains information required for connecting your XDS-PRO receiver to a satellite downlink.
2.4.1 Outdoor Antenna Grounding
Before attempting to install the XDS-PRO receiver, make sure the antenna and cable system is properly
grounded to provide some protection against voltage surges and built-up static charges.
a. Use No.10 AWG (5.3mm) copper, No.8 AWG (8.4mm) aluminum, No.7 AWG (10mm) copper-clad steel
or bronze wire or larger, as ground wire.
b. Secure antenna lead-in and ground wires to house with stand-off insulators spaced from 4 feet (1.22m)
to 6 feet (1.83m) apart.
c. Mount antenna discharge unit as close as possible to where lead-in enters house.
d. A driven rod may be used as the grounding electrode where other types of electrode systems do not
exist. Refer to the National Electrical Code, ANSI/NFPA 70-1984 for information.
e. Use jumper wire not smaller than No.6 AWG (13.3mm) copper or equivalent, when a separate
antenna grounding electrode is used.
NOTE TO THE CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV
SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-22
OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER
GROUNDING AND, IN PARTICULAR, SPECIFIES
THAT THE CABLE GROUND SHALL BE CONNECTED
TO THE GROUNDING SYSTEM OF THE BUILDING, AS
CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL