Pifco P51001 User manual

MODEL P51001 / P51002
www.pifco.co
16 Inch
Pedestal Fan
YOUR SAFETY & INSTRUCTION MANUAL
PLEASE READ CAREFULLY
Need help?
For advice, spares & returns.
Call: [phone]
8:30am to 6:00pm Monday - Friday
Visit: www.pifco.co

2
Customer support team: [phone]
Technical data
Description: 16 Inch Pedestal Fan
Model: P51001 / P51002
Rated Voltage: 220- 240V~
Frequency: 50Hz
Power consumption: 40W
Documentation
We declare that this product conforms to the following product legislation in accordance with the
following directive(s):
2014/30/EU Electromagnetic Compatibility Directive.
2014/35/EU Low Voltage Directive.
2011/65/EU Restriction of Hazardous Substances Directive.
2009/125/EC Eco-Design of Energy Related Products.
RK Wholesale LTD Quality Assurance, United Kingdom
Warranty
This product is guaranteed for 12 months from the date of original purchase. If any defect arises
due to faulty materials of workmanship, the faulty products must be returned to the place of
purchase. Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with proof of purchase.
• The product must be installed and used in accordance with the instructions contained in this
instruction guide.
• It must be used only for domestic purposes.
• It does not cover wear and tear, damage, misuse or consumable parts.
• RK Wholesale LTD has limited liability for incidental or consequential loss or damage.
• This guarantee is only Valid in the UK and Eire Only.
An extended warranty is available for this appliance.
See back page for details.

3
www.pifco.co
Wiring safety for UK use only
IMPORTANT
As the colours in the
mains lead of this
appliance may not
correspond with the
coloured markings
idenfying the terminals
in your plug, please
proceed as follows:
The wires in the mains lead are coloured in
accordance with the following code:
Blue neutral [N] Brown live [L]
Plug Fing Details (Where Applicable).
The wire coloured blue is the neutral and must
be connected to the terminal marked [N] or
coloured black.
The wire coloured brown is the live wire and
must be connected to the terminal marked [L] or
coloured red.
On no account must either the brown or the blue
wire be connected to the [EARTH] terminal .
Always ensure that the cord grip is fastened
correctly.
The plug must be ed with a fuse of the same
rang already ed and conforming to BS 1362
and be ASTA approved.
If in doubt consult a qualied electrician who will
be pleased to do this for you.
Non-Rewireable Mains Plug
If your appliance is supplied with a non-
rewireable plug ed to the mains lead and
should the fuse need replacing, you must use an
ASTA approved one (conforming to BS 1362 of
the same rang).
If in doubt, consult a qualied electrician who will
be pleased to do this for you.
If you need to remove the plug - disconnect it
from the mains - and then cut it o the mains
lead and immediately dispose of its safely. Never
aempt to reuse the plug or insert it into a
socket outlet as there is a danger of an electric
shock.
WARNING:
This appliance is double insulated. Do not connect any wire to the earth terminal.

4
Customer support team: [phone]
• Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
• Please ensure that the
appliance is used on a stable,
level, and heat resistant surface.
• DO NOT immerse cords, plugs
or any part of the appliance in
water or any other liquid.
• DO NOT leave the appliance
unattended while it is operating.
• Close supervision is necessary
when any appliance is used by
or near children or pets.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• Children shall not play with the
appliance.
• Cleaning and user maintenance
shall not be made by children
without supervision.
• Switch off at the wall socket
then remove the plug from
the socket when not in use or
before cleaning.
• If the supply cord or appliance
is damaged, stop using the
appliance immediately and seek
advice from the manufacturer
or its service agent or a similarly
qualified person.
• DO NOT let the cord hang over
the edge of a table or counter
or let it come into contact with
any hot surfaces.
• The use of accessory
attachments is not
recommended by the appliance
manufacturer apart from those
supplied with this product. DO
NOT use extension cords with
the appliance.
• DO NOT pull the plug out by
the cord as this may damage
the plug and/or the cable.
• DO NOT use this product for
anything other than its intended
use.
• This appliance is for household
use only.
• DO NOT carry the appliance by
the power cord.
PRODUCT SAFETY
When using any electrical appliance, basic safety precautions should
always be followed including the following:

5
www.pifco.co
• DO NOT use the appliance
outdoors.
• DO NOT run cord under
carpeting. DO NOT cover cord
with throw rugs, runners or the
like. Arrange cord away from
traffic area to avoid anyone
from tripping over.
• DO NOT insert or allow foreign
objects to enter any ventilation
opening as this may cause an
electric shock, fire, or damage
to an individual or a property.
• To prevent overload and blown
fuses, be sure that no other
appliance is plugged into the
same outlet (receptacle) or
into another outlet (receptacle)
wired into the same circuit.
• We DO NOT recommend use
of an extension cord as it may
overheat and cause a risk of
fire. However, if you have to
use an extension cord, the
cord should be No: 14 AWG
minimum size and rated not less
than 1875 watts, and has to be
used only for supplying power
to this fan.
• Never insert your fingers,
pencils or other objects through
the cage during operation.
• The fan should be set up on a
stable and level surface to avoid
it being knocked over.
• DO NOT expose the fan to
excessive heat or humidity as
this can cause damage to the
electrical components.
• The fan should be kept out of
the reach of children.
• In the unlikely event the
appliance develops a fault,
stop using it immediately and
seek advice from the Customer
Support Team.
HIGH VOLTAGE ROTATING PARTS

6
Customer support team: [phone]
What’s in the box & details:
Instruction Manual
Fan Unit
1. Front guard
2. Back guard
3. Decorative front panel
4. Fan blade
5. Oscillation control (Push/Pull Button)
on motor housing
6. Speed controls
7. Height adjustable metal pole
8. Height adjustable screw
9. Base pole
10. Stand connector
11. Stand part A
12. Base stabilisers
13. Stand part B
Before your first use:
1. Remove the parts from the packaging.
2. Assemble as instructed.
3. Your appliance is now ready for normal use.
Dispose of the packaging in a responsible manner.
5
1 2 3 4
6
7
8
10
9
1113
12

7
www.pifco.co
Assembling the Base and Pole:
Before using, there is some assembly required
as follows:
1 2
A B C
1. Carefully remove the fan from the
packaging and set it on a flat surface.
2. Remove the screws from each of the two
halves of the pedestal base, then slot
the two together so that they form an
X-shape.
3. Place the lower base pole over the top of
the pedestal base, so that the screw holes
on each of the four corners of the pole
base align with the corresponding holes
on the pedestal base.
4. Once the two sets of screw-holes are
correctly aligned, insert the 4 pedestal
base screws back into place. Turn each of
the screws clockwise using a screwdriver
to tighten them and secure the lower
base pole to the pedestal base.
5. Once the lower base pole is in place, pull
the extension tube out from within it
and adjust it to the desired height. Once
this tube has been set to the correct
height, turn the pole clamp in a clockwise
direction to secure it into place.
6. When the correct height has been set,
lower the upper pole and motor housing
onto the extension tube, ensuring they
are in a fully upright position. Once the
upper half of the fan has been correctly
installed, use a screwdriver to turn the
screw at the back of the upper pole in
a clockwise direction to tighten it and
secure the upper half of the fan into
place.
Assembling the Blade and Guards:
1. Once the motor housing is secured into
place, unscrew the protective cap on the
blade shaft and set it to one side.
NOTE: This cap has a reverse thread. This
means it rotates clockwise to loosen and
counter-clockwise to tighten.
2. Next, remove the nut at the back of the
motor housing and put it to one side.
3. Once both parts have been removed,
affix the back guard to the motor
housing. To do this, align the pins at the
top and bottom of the motor housing
with the three narrow notches on the
back guard, so that each pin sits flush
inside one of the notches.
4. With the back guard in position, replace
the nut onto its slot at the base of the
blade shaft, and turn it clockwise to
tighten.
NOTE: Take care to secure the back guard into
place when re-tightening the nut, to prevent it
from slipping out of position.
5. The back guard should now be secured
into place.
6. Once the back guard has been installed,
adjust the blade shaft so that the
two protruding spikes are positioned
vertically. This will help secure the fan
blades into place.
7. When the shaft is in position, slot the fan
blades into it and push them into place.
8. Once the fan blades are in place and
firmly secured, place the protective shaft
cap over the top of the fan blades and
turn it counter-clockwise to tighten it and
secure the blades into place.

8
Customer support team: [phone]
NOTE: Ensure the blades rotate unimpeded
and do not graze against the back guard. If the
fan blades become stuck or graze against the
guard mesh, they will need to be re-installed.
Repeat the steps above as necessary until the
blades move freely and naturally inside the
guard mesh.
Installing the Front Guard:
1. When the blades have been installed,
connect the front guard to the back
guard to complete fan assembly. To do
this, align the edges of the two guards,
ensuring the fixing bracket on the front
guard is at the top of the fan, directly
above the blades.
2. When the front guard is in place, locate
the locking clips around the rim of the
front guard and push each of these down
to secure the front guard into place.
3. Use the screwdriver to fix the screw and
lock nut through the hole in the bottom
of the grill.
4. Your fan is now ready for normal use.
Using your appliance:
1. Press any of the 3 speed buttons on the
fan’s control panel to turn the unit on.
The fan will automatically start operating
at the desired speed.
2. Press the 0 button on the fan’s control
panel while it is in operation to turn the
unit off.
Speed Selection:
This fan is equipped with a choice of 3 speed
settings:
1 = Minimum
2 = Medium
3 = High
1. Press the corresponding button on the
unit’s control panel to select the desired
speed.
CAUTION: Press only one of the speed control
buttons at a time. Permanent damage to the
switch housing may result if two or more of
the buttons are pressed simultaneously.
2. Press any of the other speed buttons
while the unit is in operation to change
wind speed. The fan will automatically
adjust to the new setting within a few
seconds.
3. Press the 0 button on the fan’s control
panel while it is in operation to turn the
unit off. Wind will stop emitting from
the fan grille and the fan blades will stop
rotating after a few seconds to show the
unit has been turned off.
Note:
Make sure that the fan is on a level
surface and away from any liquids.
Oscillating the fan will create a more
uniform cooling effect in the room.

9
www.pifco.co
Oscillation:
This fan is equipped with an oscillation
function, for more even heat distribution
across a room or area.
1. Push down the oscillation knob at the
back of the motor housing to turn the
oscillation function on. The fan will
automatically begin pivoting from side to
side in a fixed pattern.
2. Pull the oscillation knob while the fan is
oscillating to turn this function off. The
fan will automatically remain locked at its
current angle, and the wind flow will be
directed that way. To select a different
angle or direction for the wind, turn the
oscillation function back on, as described
above, wait until the fan is facing in
the required direction, then pull the
oscillation knob to stop the oscillation
function and lock the fan into place.
Adjusting the Air Flow:
1. This unit is equipped with a vertical tilt
function, which can be manually adjusted
to better direct the air flow.
2. To adjust the vertical tilt angle of the
fan, firmly grip the top half of the motor
housing and push it gently upwards or
downwards as required. The fan will give
off a clicking noise to indicate the tilt
mechanism is working.
3. Once the fan has been tilted, it will
automatically remain at the selected
angle until manually adjusted again.
NOTE: The fan’s horizontal angle cannot be
manually adjusted. To change the horizontal
angle of the fan, activate the oscillation
function as detailed above, wait until the fan
is at the desired angle, then pull the oscillation
knob to stop the oscillation function and lock
the fan into place.
Cleaning and care:
• Before cleaning always switch off the
appliance and remove the plug from the
electrical socket.
• To clean the outside of the fan, wipe
the exterior with a soft, damp cloth and
white soap. Use a dry cloth to polish it if
desired.
• Never use any abrasive cleaning materials
to clean the fan.
• When not in use, store the fan (preferably
in its original box) in a cool, clean and dry
location.

10
Customer support team: [phone]
WARNING:
DO NOT immerse any electrical part of the appliance in water such as motor units or plugs.
Please see cleaning secon for further instrucons.
DISPOSAL OF THE UNIT
Appliances bearing the symbol shown here may not be disposed of in domestic rubbish. You are
required to dispose of old electrical and electronic appliances like this separately.
Please visit www.recycle-more.co.uk or www.recyclenow.co.uk
for access to information about the recycling of electrical items.
Please visit www.weeeireland.ie for access to information about the recycling of electrical items
purchased in Ireland.
The WEEE directive, introduced in August 2006, states that all electrical items must be recycled,
rather than taken to landfill.
Please arrange to take this appliance to your local Civic Amenity site for recycling,
once it has reached the end of its life.
Model Idener(s): P51001 / P51002
Item Symbol Value Unit
Maximum fan ow rate F 34.56 m3/min
Fan Power input P 38.19 W
Service Value SV 0.90 (m3/min)/W
Standby power
consumpon PSB 0.00 W
Fan sound power level LWA 53.00 dB(A)
Maximum air velocity C 2.12 m/sec
Seasonal electricity
consumpon Q12.22 kWh/a
Measurement standard
for service value IEC 60879:1986 (corr.1992)
Contact Details: Imported by RK Wholesale LTD, Berryhill Road,
Stoke-on-Trent ST4 2NL

11
www.pifco.co
Notes

1219.V2
We hope you enjoy your appliance for many years.
As a thank you for purchasing one of our fantasc products,
we are oering you an extra 2 year peace of mind.
*To receive your extra 2 years guarantee, register your appliance online
within 28 days of purchase by vising:
www.pifco.co
Make sure to retain your original receipt.
Should you have a problem
with your appliance or need any spare parts please call our
Customer Support Team on:
[phone]
Distributed throughout the UK by RK Wholesale LTD