Pinnacle Technology BR1X User manual

BR1X SCANNER
USER MANUAL
Pinnacle Technology Corp.

CONTENT
1. Distinguish BT/2.4G/Wired Model ................................................................................................................ 1
1.1 Side View ................................................................................................................................................ 1
1.2 Nameplate ............................................................................................................................................... 2
2. Charge ............................................................................................................................................................ 2
2.1 Wireless Model (BT/2.4G)...................................................................................................................... 2
2.2 Wired Model ........................................................................................................................................... 2
3. Configuration ................................................................................................................................................. 3
3.1 Wired Connection ................................................................................................................................... 3
3.2 Wireless Pairing ...................................................................................................................................... 3
3.3 Continuous reading ................................................................................................................................. 4

1
1. Distinguish BT/2.4G/Wired Model
1.1 Side View
Wireless Model (BT/2.4G):
Wired Model:

2
1.2 Nameplate
Wired Model:
Bluetooth:
2.4G:
2. Charge
Only the wireless model (BT/2.4G) BR1 needs to be charged, the wired model BR1 doesn’t needs to be charged.
2.1 Wireless Model (BT/2.4G)
Place the wireless model (BT/2.4G) BR1 on the charging base, LED indicator lightens:
①Orange light slow flash indicates that the BR1 is charging.
②Orange light keeps on indicates charging full.
2.2 Wired Model
Connect the wired model BR1 to PC with USB communication cable and then the ‘Status’light flashes one
time and sounds ‘Bi’.
N: Wired Model
B: Bluetooth
W: 2.4G

3
3. Configuration
3.1 Wired Connection
After connecting the wired model BR1 to PC with USB communication cable, scanning operation can
be carried out.
3.2 Wireless Pairing
(1)2.4G Communication Model:
①Connect charging base and PC with communication cable.
②Scan ‘2.4G/Bluetooth Mode Select’code underneath the charging base; While the scanner
sounds ‘Bi’, it indicates that the scanner is in 2.4G Mode.
③Unplug the communication cable.
④Scanner reads "Pairing code" or "Pairing" code underneath the charging base to pair, and keep
the distance between scanner and charging base at most 20cm.
⑤Plug the communication cable back to PC .
（2）Bluetooth Communication Model:
①Connect charging base and PC with communication cable.
②Scan ‘2.4G/Bluetooth Mode Select’code underneath the charging base; While the scanner
sounds ‘Bi Bi’, it indicates that the scanner is in Bluetooth Mode.
③Unplug the communication cable.
④Scanner reads "Pairing code" or "Pairing" code underneath the charging base to pair, and keep
the distance between scanner and charging base at most 20cm.
⑤Plug the communication cable back to PC.
Pairing code
2.4G/Bluetooth Mode Select
2.4G/Bluetooth Mode Select
Pairing code
Note: Step ③and ④are necessary
when the scanner had been paired and
user would like to pair the scanner
with another bluetooth.

4
3.3 Continuous reading
Scan ‘Continuous reading’code, and then press the trigger key to read barcode, after that the
scanner can continuously read barcode without pressing the trigger key.
Continuous reading

FCC Statement:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.Caution: Any changes or modifications not expressly approved by the party responsiblefor compliance could void the user's authority to operate the equipment.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.