PIONEER DJ DJM-TOUR1 User manual

DJ MIXER
DJM-TOUR1
Operating Instructions (Quick Start Guide)
http://pioneerdj.com/support/
The Pioneer DJ site shown above offers FAQs, information on software, and various other types of information
and services to allow you to use your product in greater comfort.
http://rekordbox.com/
For various types of information and services regarding rekordbox™, see the Pioneer DJ website above.
http://kuvo.com/
For various types of information and services regarding KUVO, see the Pioneer DJ website above.

En
2
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1b_A1_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
Ce point d’exclamation, placé dans un
triangle équilatéral, a pour but d’attirer
l’attention de l’utilisateur sur la présence,
dans les documents qui accompagnent
l’appareil, d’explications importantes du
point de vue de l’exploitation ou de
l’entretien.
Ce symbole de l’éclair, placé dans un
triangle équilatéral, a pour but d’attirer
l’attention de l’utilisateur sur la présence, à
l’intérieur du coffret de l’appareil, de
“tensions dangereuses” non isolées d’une
grandeur suffisante pour représenter un
risque d’électrocution pour les êtres
humains.
ATTENTION :
POUR ÉVITER TOUT RISQUE
D’ÉLECTROCUTION, NE PAS ENLEVER LE
COUVERCLE (NI LE PANNEAU ARRIÈRE).
AUCUNE PIÈCE RÉPARABLE PAR
L’UTILISATEUR NE SE TROUVE À
L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À
UN PERSONNEL QUALIFIÉ UNIQUEMENT.
ATTENTION
DANGER D´ELECTROCUTION
NE PAS OUVRIR
IMPORTANT
D3-4-2-1-1b_A1_Fr

En 3
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
This product equipped with a three-wire grounding
(earthed) plug - a plug that has a third (grounding) pin.
This plug only fits a grounding-type power outlet. If you
are unable to insert the plug into an outlet, contact a
licensed electrician to replace the outlet with a properly
grounded one. Do not defeat the safety purpose of the
grounding plug.
D3-4-2-1-6_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light).
D3-4-2-1-7c*_A2_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 5 cm at rear, and 3 cm at each side).
D3-4-2-1-7d*_A1_En
AVERTISSEMENT
Cet appareil est muni d’une fiche de mise à la terre
(masse) à trois fils. Comme la fiche présente une
troisième broche (de terre), elle ne peut se brancher
que sur une prise de courant, prévue pour une mise à
la terre. Si vous n’arrivez pas à insérer la fiche dans la
prise de courant, contactez un électricien qualifié pour
faire remplacer la prise par une qui soit mise à la terre.
N’annulez pas la fonction de sécurité que procure cette
fiche de mise à la terre.
D3-4-2-1-6_A1_Fr
AVERTISSEMENT
Pour éviter les risques d’incendie, ne placez aucune
flamme nue (telle qu’une bougie allumée) sur
l’appareil.
D3-4-2-1-7a_A1_Fr
Milieu de fonctionnement
Température et humidité du milieu de fonctionnement :
De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité
relative inférieure à 85 % (orifices de ventilation non
obstrués)
N’installez pas l’appareil dans un endroit mal ventilé ou
un lieu soumis à une forte humidité ou en plein soleil
(ou à une forte lumière artificielle).
D3-4-2-1-7c*_A1_Fr
PRÉCAUTION DE VENTILATION
Lors de l’installation de l’appareil, veillez à laisser un
espace suffisant autour de ses parois de manière à
améliorer la dissipation de chaleur (au moins 5 cm à
l’arrière et 3 cm de chaque côté).
D3-4-2-1-7d*_A1_Fr
AVERTISSEMENT
Cet appareil n’est pas étanche. Pour éviter les risques
d’incendie et de décharge électrique, ne placez près de
lui un récipient rempli d’eau, tel qu’un vase ou un pot
de fleurs, et ne l’exposez pas à des gouttes d’eau, des
éclaboussures, de la pluie ou de l’humidité.
D3-4-2-1-3_A1_Fr
CAUTION
The POWER switch on this unit will not completely
shut off all power from the AC outlet. Since the power
cord serves as the main disconnect device for the
unit, you will need to unplug it from the AC outlet to
shut down all power. Therefore, make sure the unit
has been installed so that the power cord can be
easily unplugged from the AC outlet in case of an
accident. To avoid fire hazard, the power cord should
also be unplugged from the AC outlet when left
unused for a long period of time (for example, when
on vacation).
D3-4-2-2-2a*_A1_En
ATTENTION
L’interrupteur POWER de cet appareil ne coupe pas
complètement celui-ci de sa prise secteur. Comme le
cordon d’alimentation fait office de dispositif de
déconnexion du secteur, il devra être débranché au
niveau de la prise secteur pour que l’appareil soit
complètement hors tension. Par conséquent, veillez à
installer l’appareil de telle manière que son cordon
d’alimentation puisse être facilement débranché de
la prise secteur en cas d’accident. Pour éviter tout
risque d’incendie, le cordon d’alimentation sera
débranché au niveau de la prise secteur si vous
prévoyez une période prolongée de non utilisation
(par exemple avant un départ en vacances).
D3-4-2-2-2a*_A1_Fr
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En

En
4
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on
. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest se
rvice center or your
dealer for a replacement.
S002*_A1_En
WARNING: This product contains chemicals known
to the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
D36-P5_C1_En
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
D41-6-4_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE RIGHT SIDE.
RECORD THESE NUMBERS ON PAGE 19 FOR
FUTURE REFERENCE.
D36-AP9-3*_A1_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name: DJ MIXER
Model Number: DJM-TOUR1
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A.
Phone: [phone]
URL: http://www.pioneerelectronics.com
D8-10-4*_C1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En

En 5
Contents
How to read this manual
Thank you for buying this Pioneer DJ product.
Be sure to read this manual and the Operating Instructions that is avail-
able on the Pioneer DJ site. Both contain important information that you
should understand before using this product.
In particular, be sure to read “IMPORTANT SAFETY INSTRUCTIONS.”
Furthermore, be sure to keep this manual together with “Warranty.”
Be sure to read “Safety Precautions”. Store this booklet with “Warranty”
at the end of the booklet in a safe place.
!In this manual, names of channels and buttons indicated on the
product, names of menus in the software, etc., are indicated within
square brackets ([ ]). (e.g. [MASTER] channel, [ON/OFF], [File]
menu)
!Please note that the screens and specifications of the software
described in this manual as well as the external appearance and
specifications of the hardware are currently under development and
may differ from the final specifications.
!Please note that depending on the operating system version, web
browser settings, etc., operation may differ from the procedures
described in this manual.
This manual provides brief descriptions regarding the names of parts
of this unit and the connections between this unit and peripherals.
For more detailed instructions on using this unit, see the Operating
Instructions for this unit.
!For how to obtain the Operating Instructions for this unit, see
Acquiring this unit’s Operating Instructions on page 6.
Before start
Features....................................................................................................... 6
What’s in the box ........................................................................................ 6
Acquiring this unit’s Operating Instructions ........................................... 6
Preparing the software............................................................................... 6
Part names and functions
Rear panel, front panel............................................................................... 7
Control Panel .............................................................................................. 9
Connections
Connecting input terminals..................................................................... 12
Connecting output terminals .................................................................. 13
Connecting to the control panel.............................................................. 13
Operation
Basic Operation ........................................................................................ 14
How to use the TILTABLE DISPLAY......................................................... 14
About the display shade........................................................................... 14
Additional information
Troubleshooting........................................................................................ 15
Changing the settings.............................................................................. 15
About trademarks and registered trademarks ...................................... 15
Cautions on copyrights ............................................................................ 15
Specifications............................................................................................ 16

En
6
Before start
Features
This unit is a mixer for professional DJs, offering the variety of functions,
durability, and operability required for working not only in discos and
nightclubs but also at large-scale music festivals and other events. It
not only has an unprecedented overwhelming high sound quality, high
reliability design and support for professional quality connections, it
is also equipped with a wide range of features for DJ performances,
including the SOUND COLOR FX, BEAT FX, PRO DJ LINK, BROWSE,
and WAVE functions, thereby offering strong support for all types of DJ
performances.
What’s in the box
!Power cord x1
!USB cable1x1
!Display shade x1
!Operating Instructions (Quick Start Guide) (This document)
1When connecting two PCs, provide a USB cable compliant with USB
2.0 separately.
Acquiring this unit’s Operating
Instructions
Various instructions are sometimes provided as files in PDF format.
Adobe®Reader®must be installed in order to view PDF format files.
1 Launch a web browser on the computer and access
the Pioneer DJ site below.
http://www.pioneerdj.com/
2 Click [Support].
3 Click the [FIND TUTORIALS & MANUALS] icon.
4 Click the [DJM-TOUR1] icon in the [MIXER] category.
5 Click on the required language on the download
page.
Preparing the software
About the driver software
This driver software is an exclusive driver for outputting audio signals
from a computer.
Obtaining the driver software
1 Launch a web browser on the computer and access
the Pioneer DJ site below.
http://www.pioneerdj.com/
2 Click the [Support] icon.
3 Click the [FIND SOFTWARE & FIRMWARE UPDATES]
icon.
4 Click the [DJM-TOUR1] icon in the [MIXER] category.
5 After clicking [Drivers], download the latest driver
software from the download page.

En 7
Part names and functions
Part names and functions
Rear panel, front panel
PHONES
LINK
CH4
EXTENSION CH3 CH2CH1
IN
OFFON
75Ω
MASTER2 REC OUT MASTER1
WORD CLOCK
DIGITAL OUT
INTERNET
DIGITAL IN BOOTH
AES/EBU
2 4 54554 54 6 61 7 8
k
9
gh c bd
ja
fi e
3
1 Kensington security slot
2 POWER button (page 14)
Turns this unit’s power on and off.
3 EXTENSION terminal (page 12)
Used when extending PRO DJ LINK. Connect this to the LAN termi-
nal of a computer with rekordbox installed, etc.
4 PHONO terminals (page 12)
Connect to a phono level (MM cartridge) output device. Do not input
line level signals.
To connect a device to the [PHONO] terminals, remove the short-
circuit pin plug inserted in the terminals.
Insert this short-circuit pin plug into the [PHONO] terminals when
nothing is connected to them to cut external noise.
5 LINE terminals (page 12)
Connect to a DJ player or a line level output component.
6 SIGNAL GND terminal (page 12)
Connects an analog player’s ground wire here. This helps reduce
noise when the analog player is connected.
7 MIC2 terminal (page 12)
Connects a microphone here.
8 MIC1 terminal (page 12)
Connects a microphone here.
9 INTERNET terminal
Connect to a router, etc. that is connected to the Internet. Used when
connecting with the KUVO system.
Connect a device to be connected to PRO DJ LINK not to this termi-
nal but to the [EXTENSION] terminal.
a DIGITAL IN terminal (page 12)
Connect these to the digital coaxial output terminals on DJ players,
etc. The sound may be momentarily interrupted when the output
signal sampling frequency is switched.
b 75 Ωtermination ON/OFF switch
c WORD CLOCK input terminal
Set the external clock generator to MASTER and implement digital
master output synchronized with another device.
Use a cable with an impedance of 75 Ω for the connection between
the terminals. Performance is not guaranteed when a cable with an
impedance of other than 75 Ω is used.
Change the 75 Ω termination ON/OFF switch setting according to
the connection method.
—ON
—For connecting with the external clock generator on a one-to-
one basis
—For terminating with this unit when connecting a combina-
tion of multiple devices
—OFF
—For terminating with another device when connecting a
combination of multiple devices

En
8
d DIGITAL MASTER OUT terminal (page 13)
Connect to the digital input terminal of a preamplifier, etc. The mas-
ter channel audio is output in AES/EBU format. Be careful not to
accidentally connect this terminal to an analog input terminal.
Be careful not to accidentally insert the power cord of another
unit.
e LINK CH terminal (page 12)
Connect to the LINK terminal of a DJ player of Pioneer DJ (PRO DJ
LINK).
f BOOTH terminals (page 13)
These are output terminals for a booth monitor.
Be careful not to accidentally insert the power cord of another
unit.
g REC OUT terminals (page 13)
These are output terminals for recording.
h MASTER2 terminals (page 13)
Connect these to the analog input terminals of a power amplifier, etc.
i MASTER1 terminals (page 13)
Connect these to the analog input terminals of a power amplifier, etc.
Be sure to use these as balanced outputs.
Be careful not to accidentally insert the power cord of another
unit.
j AC IN
Connects to a power outlet using the included power cord. Wait until
all connections between the equipment are completed before con-
necting the power cord.
Be sure to use the included power cord.
k SECOND HEADPHONES terminal
Connect headphones. Supports a 1/4” stereo phone plug.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If
accidentally swallowed, contact a doctor immediately.

En 9
Part names and functions
Control Panel
TIME
MAX
LEVEL /DEPTH
ON /OFF
MIN
MAX
LEVELON/OFF
MIN
AB
CROSS FA DER ASSIGN
MASTER
0
MIXING
LEVEL
PHONES
CUE
CUE
CUE
CUE
10
9
8
7
6
5
4
3
2
1
0
1
10
9
8
7
6
5
4
3
2
1
0
7
1
10
9
8
7
6
5
4
3
2
1
0
7
1
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
EQ
ISOLATOR
BOOTH MONITOR
EQ CURVE
CH FADER
CROSS FADER
0
dB RL
LEVEL
0
BALANCE
RL
TAP
BEAT FX
BEAT
X-PAD
STEREO
MONO SPLIT
HEADPHONES
SPACE
NOISE CRUSH FILTER
DUB
ECHO SWEEP
LINK
SOUND COLOR FX
LEVEL
HI
LOW
EQ
12 12
12 12
MIC
USB
MIDI
ON/OFF
0 0
CLIP
DECK 3/C
CLIP
DECK 1/A
CLIP
DECK 2/B
TRIM
9
CLIP CLIP
DECK 4/D
EQ /
LOW
6
- 26
/
MID
6
- 26
/
HI
6
- 26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
BEAT FX
BEAT FX
BEAT FX
CUE
BEAT FX
CUE
BEAT FX
CUE
BEAT FX BEAT FX
PARAMETER
MAXMIN
AB
DIGITAL LINE
PHONO
AB
RETURN
AUX
DIGITAL LINE
PHONO
AB
RETURN
AUX
DIGITAL LINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
12
15
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
dB
12
9
6
3
0
-3
-6
-18
-24
MASTER
MIC
AUX
CROSS
FADER
FLANGER
PHASER
PITCH
PING PONG ROLL
SLIP ROLL
DELAY
TRANS
FILTER
SPIRAL
ECHO
REVERB
VINYL BRAKE
FX FREQUENCY
LOWMIDHI
SEND/ RETURN
SEND/ RETURN
SEND
SEND/ RETURN
AUX
SEND/ RETURN
RETURN
SECOND HEADPHONES
MASTER
1/4
14
1/81/2
3/4
1/16
2
1
A
B
23
4
COLOR
HILOW
COLOR
HILOW
COLOR
HILOW
COLOR
HILOW
MIC1 MIC2
BA THRU
BATHRU
BATHRU BATHRU
CUE
CUE
CUE
CUE
CUE
CUE
CUE
CUE
-12
MASTER
0
MIXING
LEVEL
CUE
STEREOMONO SPLIT
TRIM
9
CLIP
L (MONO)
R
BALANCE
L (MONO)
L (MONO)
R
R
UNBALANCE
UNBALANCE
CH 1
CH 2
CH 3
CH 4
MASTER
LINK
AUX
TRIM
9
EQ /
LOW
6
- 26
/
MID
6
- 26
/
HI
6
- 26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
TRIM
9
EQ /
LOW
6
- 26
/
MID
6
- 26
/
HI
6
- 26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
TRIM
9
EQ /
LOW
6
- 26
/
MID
6
- 26
/
HI
6
- 26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
m
k
l
h
g
2
e
d
c
b
2
1
2
3
4
6
5
B
l
C
F
D
L
M
N
O
P
T
U
V
A
G
Q
R
z
3
i
7
E
S
o
r
6
5
4
p
3
1
q
n
t
s
5
u
w
x
y
3
2
o
6
5
4
p
3
1
q
n
2
o
6
5
4
p
3
1
q
n
2
o
6
5
4
p
3
1
q
n
22
j
H
I
J
K
8
v
9
a
f
W
1 Channel Fader (page 14)
Adjusts the level of audio signals output in each channel.
2 Effect channel selector indicator
The indicator of the channel selected with the effect channel selector
switch lights.
3 CUE button (page 14)
Presses the [CUE] button(s) for the channel(s) you want to monitor.
4 Channel Level Indicator (page 14)
Displays the sound level of the respective channels before passing
through the channel faders.
5 CLIP indicators
An indicator lights when sound with an excessively high volume is
input to a channel.
6 TRIM control (page 14)
Adjusts the level of audio signals input in each channel.
7 AUX terminal
Connect to the output terminal of another mixer or a line level output
component. When [L (MONO)] only is connected, the audio input to
[L (MONO)] is also input to [R].
8 TILTABLE DISPLAY unlock button
Releases the lock that is engaged when the TILTABLE DISPLAY is
closed.

En
10
9 TILTABLE DISPLAY
For details on how to use the TILTABLE DISPLAY, see the operating
instructions.
a PHONES terminal (page 14)
Connect headphones here.
Supports a 1/4” stereo phone plug and a 3.5 mm stereo mini plug,
and two sets of headphones can be used at the same time.
b LEVEL control (page 14)
Adjusts the sound level output from the headphones.
c MIXING control (page 14)
This adjusts the monitor volume balance of the sound of channels for
which the [CUE] button is pressed and the sound of the [MASTER]
channel.
d MONO SPLIT, STEREO selector switch (page 14)
Switches how the monitor sound output from the headphones is
distributed.
e PARAMETER control
Adjusts the SOUND COLOR FX parameter.
f SOUND COLOR FX buttons
These turn the SOUND COLOR FX effects on/off.
g OFF, ON, TALK OVER selector switch (page 14)
Turns the microphone on/off.
h Microphone indicator (page 14)
i EQ (HI, LOW) controls (page 14)
These adjust the tone quality of the [MIC1] and [MIC2] channels.
j MIC LEVEL control (page 14)
Adjusts the level of the sound input to the [MIC1] and [MIC2]
channels.
k MIDI ON/OFF buttons
Switches the MIDI function on and off.
l USB connection indicator
An indicator lights when a computer is connected. It flashes when
the driver software is not installed on the computer.
m USB terminal (page 13)
Connect the computer.
n Input selector switches (page 14)
Selects the input source of each channel from the components con-
nected to this unit.
o EQ/ISO (HI, MID, LOW) controls
These adjust the sound quality of the respective channels.
p COLOR control
This changes the parameters of the SOUND COLOR FX of the differ-
ent channels.
q CROSS FADER ASSIGN (A, THRU, B) selector switch
(page 14)
Sets the output destination of each channel to [A] or [B].
r Crossfader (page 14)
Outputs audio signals assigned by the crossfader assign switch cor-
responding to the curve characteristics selected by [CROSS FADER]
(Crossfader Curve Selector Switch).
s MASTER LEVEL control (page 14)
Adjusts the audio level output from the [MASTER1] and [MASTER2]
terminals.
t Master Level Indicator (page 14)
Displays the audio level output from the [MASTER1] and [MASTER2]
terminals.
u BALANCE control
Adjusts the left/right balance of the sound output from the
[MASTER1] terminals, etc.
v BOOTH MONITOR control (page 14)
Adjusts the level of audio signals output from the [BOOTH] terminal.
w EQ CURVE (ISOLATOR, EQ) selector switch
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
x CH FADER ( , , ) selector switch
Switches the channel fader’s curve characteristics.
y CROSS FADER ( , , ) curve selector switch
This switches the crossfader curve characteristics.
z SEND/RETURN (1/4” JACK, ) selector switch
Switches the input/output source of the SEND/RETURN channel.
Select either the device connected to the [SEND/RETURN] terminal
on the control panel or the device connected to the mobile device
connection terminal.
A RETURN TYPE (AUX, INSERT) selector switch
Selects the SEND/RETURN method.
B Mobile device connection terminal (USB port)
Connect a mobile device to enable SEND/RETURN to be used for
apps.
C SEND/RETURN ON/OFF button
Turns SEND/RETURN on and off.
D SEND/RETURN LEVEL control
Adjusts the sound level of SEND/RETURN.
E Main unit display
Displays the effect name, BPM, effect parameter, etc.
F X-PAD
BEAT FX is on while this is touched. Also, the parameter can be
adjusted depending on the place touched.
G BEAT c, dbuttons
Set the beat fraction for synchronizing the effect sound.
H TAP button
When the BPM measurement mode is set to [TAP], tap the button
with a finger to input the BPM manually.
I QUANTIZE (UTILITY, WAKE UP) button
—QUANTIZE: When the QUANTIZE function is turned on for BEAT
FX, the effect is applied to the sound without getting out of tempo
with the currently playing track.
—UTILITY: Displays the [UTILITY] screen.
—WAKE UP: Cancels the standby state.
J AUTO/TAP button
Switches the BPM measurement mode.
K FX FREQUENCY button
Select the range to apply BEAT FX. BEAT FX is applied to the range of
the button that is lit.
L Beat effect selector switch
Switches the BEAT FX effect type.
M Effect channel selector switch
Switches the channel to which the BEAT FX is to be applied.
N TIME control
Adjusts the BEAT FX’s time parameter.
O LEVEL/DEPTH control
Adjusts the BEAT FX’s quantitative parameter.
P Beat effect ON/OFF button
Turns BEAT FX on and off.

En 11
Part names and functions
Q SEND terminals (page 13)
Connect to the input terminal of an external effector. When
[L (MONO)] only is connected, monaural audio is output.
R RETURN terminals (page 13)
Connect to the output terminal of an external effector. When the
[L (MONO)] channel only is connected, the [L (MONO)] channel
input is simultaneously input to the [R] channel.
S SECOND HEADPHONES CUE button
Press the [CUE] button for the channel you want to monitor with
SECOND HEADPHONES.
T SECOND HEADPHONES MONO SPLIT / STEREO
selector switch
Switches how the monitor sound output from SECOND
HEADPHONES is distributed.
U SECOND HEADPHONES MIXING control
This adjusts the monitor volume balance of the sound of channels for
which the [CUE] button is pressed and the sound of the [MASTER]
channel.
V SECOND HEADPHONES LEVEL control
Adjusts the level of audio output from SECOND HEADPHONES.
W Display shade attachment screw hole (page 14)
Do not pull on the channel fader and crossfader knobs with excessive
force. The knobs have a structure by which they cannot be pulled off
easily. Pulling the knobs strongly may result in damaging the unit.

En
12
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
Refer to the operating instructions for the component to be connected.
!When connecting using a LAN cable, use an STP (CAT5e shielded) cable.
!Do not disconnect the LAN cable when music files and/or information are being shared using PRO DJ LINK.
!To connect to the KUVO server, a separate contract with and payment to a provider offering Internet services is required.
Connecting input terminals
LINK
CH4
EXTENSION CH3 CH2 CH1
IN
OFFON
75Ω
MASTER2 REC OUT MASTER1
WORD CLOCK
DIGITAL OUT
INTERNET
DIGITAL IN BOOTH
AES/EBU
LR
LR
LRLR LR
LRLRLR
To power outlet
CDJ-TOUR1 or CDJ-2000NXS2 CDJ-TOUR1 or CDJ-2000NXS2 Clock output device
Computer
1
Analog player Analog player Microphone Internet
Router for Internet
connection
(commercially
available product)
1When connecting multiple computers, use a network device (100Base-TX compatible switching hub, wireless router, or access point).
Normal operation may not be possible depending on the connected network device.

En 13
Connections
Connecting output terminals
LINK
CH4
EXTENSION CH3 CH2 CH1
IN
OFFON
75Ω
MASTER2 REC OUT MASTER1
WORD CLOCK
DIGITAL OUT
INTERNET
DIGITAL IN
BOOTH
AES/EBU
LRLR
2 2 2
Power amplifier
1
Power amplifier
1
Analog input
recording device
Power amplifier
(for booth monitor)
Digital audio
input device
1Be sure to use the [MASTER1] terminals only for a balanced output. Connection with an unbalanced input (such as RCA) using an XLR to RCA
converter cable (or converter adapter), etc., may lower the sound quality and/or result in noise.
For connection with an unbalanced input (such as RCA), use the [MASTER2] terminals.
2Be careful not to accidentally connect the power cord of another product to the [MASTER1], [BOOTH], or [DIGITAL MASTER OUT]
terminal.
Connecting to the control panel
MAX
LEVEL /DEPTH
ON /OFF
MIN
AB
CROSS FA DER ASSIGN
0
LEVEL
PHONES
CROSS FADER
BATHRU
BATHRU
BATHRU BATHRU
MASTER
0
MIXING
LEVEL
CUE
MAX
LEVELON/ OFF
MIN
LEVEL
0
BEAT FX
LEVEL
HI
MIC
USB
MIDI
ON/OFF
0 0
CLIP
DECK 3/C
TRIM
9
CLIP
DECK 1/A
TRIM
9
CLIP
DECK 2/B
TRIM
9
CLIP CLIP
DECK 4/D
MID
HI
6
- 26
/
12
9
6
3
0
-3
-6
9
MID
HI
6
- 26
/
12
9
6
3
0
-3
-6
9
MID
HI
6
- 26
/
12
9
6
3
0
-3
-6
9
MID
HI
6
- 26
/
12
9
6
3
0
-3
-6
9
AB
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITAL LINE
PHONO
AB
RETURN
AUX
12
15
9
6
3
0
-3
6
SEND/ RETURN
SEND/ RETURN
SEND
SEND/ RETURN
AUX
SEND/ RETURN
RETURN
MASTER
MIC1 MIC2
CUE
TRIM
9
L (MONO)
R
L (MONO)
L (MONO)
R
R
UNBALANCE
UNBALANCE
CH 1
TRIM
9
BALANCE
SECOND HEADPHONES
USB hubs cannot be used.
TIME
MAX
LEVEL/DEPTH
ON/OFF
MIN
MAX
LEVELON/OFF
MIN
AB
CROSSFADERASSIGN
MASTER
0
MIXING
LEVEL
PHONES
CUE
CUE
CUE
BATHRU
BATHRU
BATHRU BATHRU
CUE
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
TRIM
9
EQISOLATOR
BOOTHMONITOR
EQCURVE
CHFADER
CROSSFADER
0
dB RL
LEVEL
0
BALANCE
RL
TAP
BEATFX
BEAT
X-PAD
STEREO
MONOSPLIT
HEADPHONES
SPACE
NOISECRUSHFILTER
DUB
ECHOSWEEP
LINK
SOUNDCOLORFX
LEVEL
HI
LOW
EQ
12 12
12 12
MIC
USB
MIDI
ON/OFF
00 0
CLIP
DECK3/C
TRIM
9
CLIP
DECK1/C
TRIM
9
CLIP
DECK2/C
TRIM
9
CLIP CLIP
DECK4/C
EQ/
LOW
6
-
26
/
MID
6
-
26
/
HI
6
-
26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
EQ/
LOW
6
-
26
/
MID
6
-
26
/
HI
6
-
26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
EQ/
LOW
6
-
26
/
MID
6
-
26
/
HI
6
-
26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
EQ/
LOW
6
-
26
/
MID
6
-
26
/
HI
6
-
26
/
ISO
dB
12
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
BEATFX
BEATFX
CUE
COLOR
HILOW
BEATFX
CUE
COLOR
HILOW
BEATFX
CUE
COLOR
HILOW
BEATFXBEATFX
PARAMETER
MAXMIN
AB
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
DIGITALLINE
PHONO
AB
RETURN
AUX
12
15
9
6
3
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
MASTERMIC
CROSS
FADER
FLANGER
PHASHER
PITCH
PINGPONGROLL
SLIPROLL
DELAY
TRANS
FILTER
SPIRAL
ECHO
REVERB
VINYLBRAKE
FXFREQUENCY
LOWMIDHI
SEND/RETURN
MASTER
1/4
14
1/81/2
3/4
1/16
2
1
A
B
23
4
COLOR
HILOW
MIC1 MIC2
Headphones Headphones
USB port covers 1 USB port covers 1
Computer
Connect using USB cables.
USB hubs cannot be used.
Mobile device
2
External effector
3
DJ mixer, etc.
1Do not push or pull hard on a USB port cover. It could be damaged.
2When connecting a mobile device, use the cable supplied with the device.
For information on compatible mobile devices, see the Pioneer DJ site below.
http://pioneerdj.com/support/
3Connect the external effector to both the [SEND] terminal and [RETURN] terminal.

En
14
Operation
Basic Operation
Outputting sound
1 Press [POWER] button.
Turn on the power of this unit.
2 Switch the input selector switches.
Selects the input sources for the different channels from among the
devices connected to this unit.
3 Turn the [TRIM] control.
Adjusts the level of audio signals input in each channel.
The corresponding channel level indicator lights when audio signals are
being properly input to that channel.
4 Move the channel fader away from you.
Adjusts the level of audio signals output in each channel.
5 Switch the [CROSS FADER ASSIGN (A, THRU, B)]
selector switch.
Switches the output destination of each channel.
6 Set the crossfader.
This operation is not necessary when the [CROSS FADER ASSIGN (A,
THRU, B)] selector switch is set to [THRU].
7 Turn the [MASTER LEVEL] control.
Audio signals are output from the [MASTER1] and [MASTER2]
terminals.
The master level indicator lights.
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE] button(s) for the channel(s) you want
to monitor.
3 Switch the [MONO SPLIT, STEREO] selector switch.
4 Turn the [MIXING] control.
This adjusts the monitor volume balance of the sound of channels for
which the [CUE] button is pressed and the sound of the [MASTER]
channel.
5 Turn the [LEVEL] control for [HEADPHONES].
The sound of the channels for which the [CUE] button is pressed is
output from the headphones.
!When the [CUE] button is pressed again, monitoring is canceled.
Using a microphone
1 Connect a microphone to the [MIC1] or [MIC2]
terminal.
2 Set the [OFF, ON, TALK OVER] selector switch to [ON]
or [TALK OVER].
!When set to [TALK OVER], the sound of channels other than the
[MIC] channel is attenuated by 18 dB (default) when a sound of –10
dB or greater is input to the microphone.
!The sound attenuation level of [TALK OVER] can be changed with
[UTILITY]. For details on how to change the level, see the Operating
Instructions.
!The TALK OVER mode can be switched to normal mode or advanced
mode. For details on how to change the mode, see the Operating
Instructions.
3 Turn the [MIC1 LEVEL] control or [MIC2 LEVEL]
control.
Adjust the level of the sound output from the [MIC] channel.
!Pay attention that rotating to the extreme right position outputs a
very loud sound.
4 Input audio signals to the microphone.
Audio is output from the [BOOTH]
terminal
Turn the [BOOTH MONITOR] control.
Adjusts the level of audio signals output from the [BOOTH] terminal.
How to use the TILTABLE DISPLAY
When the display is closed, the lock engages when the display is at a
certain angle. When the lock is engaged, move the display back a little
in the open direction once and then press unlock button 1. To fully close
the display, lower the display while pressing the unlock button.
Be careful not to get your fingers caught in the Tiltable display when
opening and closing it.
About the display shade
If outdoor light reflecting on the display bothers you, it can be reduced
by attaching the supplied display shade.

En 15
Additional information
Additional information
Troubleshooting
!If you think that there is something wrong with this unit, check the following items, and also access [FAQ & DJ software support information] on
the Pioneer DJ support site and check [FAQ] for [DJM-TOUR1].
http://pioneerdj.com/support/
Sometimes the problem may lie in another component. Inspect the other components and electrical appliances being used. If the problem cannot
be rectified, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
!This unit may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by unplug-
ging the power cord then plugging it back in.
Problem Check Remedy
The power is not turned on. Is the power cord properly connected? Plug in the power cord to an AC outlet.
No sound or small sound. Is the input selector switch set to the proper
position?
Switch the input selector switch to switch the channel’s input source.
(page 14)
Are the connection cables properly connected? Connect the connection cables properly. (page 12)
Are the terminals and plugs dirty? Clean the terminals and plugs before making connections.
Distorted sound. Is the sound level output from the [MASTER]
channel appropriately set?
Adjust the [MASTER LEVEL] control so that the master channel level indicator
lights at around [0 dB] at the peak level. (page 14)
Is the level of audio input to each channel properly
set?
Adjust the [TRIM] control so that the channel level indicator lights at about
[0 dB] at the peak level. (page 14)
Can’t crossfade. Are the [CROSS FADER ASSIGN (A, THRU, B)]
selector switches properly set?
Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switches for the different
channels properly. (page 14)
Sound is distorted when an ana-
log player is connected to this
unit’s [PHONO] terminals.
Or, lighting of the channel level
indicator does not change even when
the [TRIM] control is turned.
Have you connected an analog player with a built-
in phono equalizer?
Connect the analog player with built-in phono equalizer to the [LINE] terminals.
(page 12)
If the analog player with built-in phono equalizer has a PHONO/LINE selector
switch, switch it to PHONO.
Is an audio interface for computers connected
between the analog player and this unit?
If the output of the audio interface for computers is line level, connect it to the
[LINE] terminals. (page 12)
If the analog player has a PHONO/LINE selector switch, switch it to PHONO.
Changing the settings
!For details on how to change the settings of this unit, see “Changing
the settings” in the Operating Instructions.
About trademarks and registered
trademarks
!"Pioneer DJ" is a trademark of PIONEER CORPORATION, and is used
under license.
The names of companies and products mentioned herein are trade-
marks or registered trademarks of their respective owners.
Cautions on copyrights
Recordings you have made are for your personal enjoyment and accord-
ing to copyright laws may not be used without the consent of the copy-
right holder.
!Music recorded from CDs, etc., is protected by the copyright laws of
individual countries and by international treaties. It is the full respon-
sibility of the person who has recorded the music to ensure that it is
used legally.
!When handling music downloaded from the Internet, etc., it is the
full responsibility of the person who has downloaded the music to
ensure that it is used in accordance with the contract concluded
with the download site.

En
16
Specifications
General
Power............................................................AC 110 V to 240 V, 50 Hz/60 Hz
Power consumption............................................................................... 82 W
Power consumption (standby)............................................................. 0.4 W
Main unit weight ...................................................................16.1 kg (35.5 lb)
External dimensions
(When TILTABLE DISPLAY part is in closed state)
............................................ 445.2 mm (W) x 179.1 mm (H) x 451.6 mm (D)
(17.5 in. (W) x 7.1 in. (H) x 17.8 in. (D))
(When TILTABLE DISPLAY part is upright at 90 degrees)
.............................................. 445.2 mm (W) x 418 mm (H) x 457.7 mm (D)
(17.5 in. (W) x16.5 in. (H) × 18 in. (D))
(When TILTABLE DISPLAY part is in open state)
............................................ 445.2 mm (W) x 203.1 mm (H) x 694.5 mm (D)
(17.5 in. (W) x 8 in. (H) x 27.3 in. (D))
Tolerable operating temperature ......... +5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity ...................... 5 % to 85 % (no condensation)
Audio Section
Sampling rate ......................................................................................96 kHz
D/A converter .......................................................................................32 bits
A/D converter .......................................................................................24 bits
Frequency characteristic
LINE ................................................................................. 20 Hz to 40 kHz
S/N ratio (rated output)
PHONO............................................................................................ 88 dB
LINE ............................................................................................... 105 dB
MIC1, MIC2..................................................................................... 79 dB
Total harmonic distortion (LINE — MASTER1)................................0.005 %
Standard input level / Input impedance
PHONO............................................................................. –52 dBu/47 kΩ
LINE .................................................................................. –12 dBu/47 kΩ
MIC1, MIC2........................................................................ –52 dBu/8 kΩ
RETURN............................................................................ –12 dBu/47 kΩ
AUX .................................................................................. –12 dBu/47 kΩ
Standard output level / Load impedance / Output impedance
MASTER1................................................ +8 dBu/10 kΩ/100 Ωor lower
MASTER2................................................ +2 dBu/10 kΩ/390 Ωor lower
REC OUT .....................................................–8 dBu/10 kΩ/22 Ωor lower
BOOTH.................................................... +8 dBu/10 kΩ/100 Ωor lower
SEND .........................................................–12 dBu/10 kΩ/1 kΩor lower
PHONES ..................................................... +8.5 dBu/32 Ω/1 Ωor lower
Rated output level / Load impedance
MASTER1........................................................................+25 dBu/10 kΩ
MASTER2........................................................................+21 dBu/10 kΩ
Digital Input / Output impedance
WORD CLOCK.......................................................... TTL/75 Ω(ON/OFF)
AES/EBU ......................................................................................... 110 Ω
Crosstalk (LINE).................................................................................... 82 dB
Channel equalizer characteristic
HI .....................................................................–26 dB to +6 dB (30 kHz)
MID....................................................................–26 dB to +6 dB (1 kHz)
LOW ..................................................................–26 dB to +6 dB (20 Hz)
Microphone equalizer characteristic
HI ...................................................................–12 dB to +12 dB (10 kHz)
LOW ..............................................................–12 dB to +12 dB (100 Hz)
Input / Output terminals
PHONO input terminal
RCA pin jacks.................................................................................. 4 sets
LINE input terminal
RCA pin jacks.................................................................................. 4 sets
MIC1 input terminal (XLR/TRS)
XLR connector & 1/4” TRS jack ........................................................1 set
MIC2 input terminal (TRS)
1/4” TRS jack .....................................................................................1 set
RETURN Input terminals (TS)
1/4” TS jack........................................................................................ 1 set
AUX input terminal (XLR/TRS)
XLR connector & 1/4” TRS jack ........................................................1 set
DIGITAL IN coaxial input terminal
RCA pin jacks.................................................................................. 4 sets
MASTER output terminal
XLR connector...................................................................................1 set
RCA pin jacks....................................................................................1 set
BOOTH output terminal
XLR connector...................................................................................1 set
REC OUT output terminal
RCA pin jacks....................................................................................1 set
SEND output terminal (TS)
1/4” TS jack........................................................................................ 1 set
DIGITAL MASTER OUT AES/EBU
XLR connector...................................................................................1 set
WORD CLOCK input terminals
BNC jack............................................................................................1 set
PHONES output terminal
1/4” stereo phone jack.................................................................... 2 sets
3.5 mm stereo mini jack ...................................................................1 set
USB terminal
Type A ................................................................................................1 set
Power supply...5 V/2.1 A or less
B type............................................................................................... 2 sets
EXTENSION terminal
LAN terminal (100 Base-TX) ............................................................1 set
LINK CH terminal
LAN terminal (100 Base-TX) ........................................................... 4 sets
INTERNET terminal
LAN terminal (100 Base-TX) .............................................................1 set
Tiltable display (13-inch)
Display type ...........................Active matrix TFT liquid crystal display (LCD)
Supported languages .............................................................. 18 languages
!The specifications and design of this product are subject to change
without notice.

17
En
Additional information

18 En

UCP0116
Pioneer DJ Americas, Inc.
LIMITED WARRANTY
WARRANTY VALID ONLY IN THE U.S.A. AND CANADA
WARRANTY
Pioneer DJ Americas, Inc. (PDJA) warrants that products distributed by PDJA in the U.S.A. and Canada that fail to function properly under normal use due to a manufacturing
defect when installed and operated according to the owner’s manual enclosed with the unit will be repaired or replaced with a unit of comparable value, at the option of PDJA,
without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PDJA.
THIS LIMITEDWARRANTY APPLIESTOTHE ORIGINAL OR ANY SUBSEQUENT OWNER OFTHIS PIONEER DJ PRODUCT DURINGTHEWARRANTY PERIOD PROVIDEDTHE
PRODUCT WAS PURCHASED FROM AN AUTHORIZED PIONEER DJ DISTRIBUTOR/DEALER INTHE U.S.A. OR CANADA. YOU WILL BE REQUIREDTO PROVIDE A SALES
RECEIPT OR OTHERVALID PROOF OF PURCHASE SHOWINGTHE DATE OF ORIGINAL PURCHASE OR,IF RENTED,YOUR RENTAL CONTRACT SHOWINGTHE PLACE AND
DATE OF FIRST RENTAL. IN THE EVENT SERVICE IS REQUIRED, THE PRODUCT MUST BE DELIVERED WITHIN THE WARRANTY PERIOD, TRANSPORTATION PREPAID,
ONLY FROMWITHINTHE U.S.A. AS EXPLAINED INTHIS DOCUMENT. YOUWILL BE RESPONSIBLE FOR REMOVAL AND INSTALLATION OFTHE PRODUCT. PDJA WILL PAY
TO RETURNTHE REPAIRED OR REPLACEMENT PRODUCTTOYOUWITHINTHE U.S.A.
PRODUCT WARRANTY PERIOD Parts Labor
DJ Audio and Video ................................................................................................................................................................................... 1 Year 1 Year
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IF THIS PRODUCT WAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THIS PRODUCT IS SOLD STRICTLY “AS IS” AND “WITH ALL FAULTS".
PIONEER DJ SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES.
THIS WARRANTY DOES NOT APPLY IF THE PRODUCT HAS BEEN SUBJECTED TO POWER IN EXCESS OF ITS PUBLISHED POWER RATING.
THISWARRANTY DOES NOT COVERTHE CABINET OR ANY APPEARANCE ITEM, USER ATTACHED ANTENNA, ANY DAMAGETO RECORDS OR RECORDINGTA PES OR DISCS, ANY
DAMAGETO THE PRODUCT RESULTING FROM ALTERATIONS, MODIFICATIONS NOT AUTHORIZED IN WRITING BY PIONEER DJ, ACCIDENT, MISUSE OR ABUSE, DAMAGE DUETO
LIGHTNING ORTO POWER SURGES, SUBSEQUENT DAMAGE FROM LEAKING, DAMAGE FROM INOPERATIVE BATTERIES,ORTHE USE OF BATTERIES NOT CONFORMINGTOTHOSE
SPECIFIED INTHE OWNER’S MANUAL.
THIS WARRANTY DOES NOT COVER THE COST OF PA RTS OR LABOR WHICH WOULD BE OTHERWISE PROVIDED WITHOUT CHARGE UNDER THIS WARRANTY OBTAINED FROM
ANY SOURCE OTHERTHAN A PIONEER DJ AUTHORIZED SERVICE COMPANY OR OTHER DESIGNATED LOCATION. THISWARRANTY DOES NOT COVER DEFECTS OR DAMAGE CAUSED
BYTHE USE OF UNAUTHORIZED PA RTS OR LABOR OR FROM IMPROPER MAINTENANCE.
ALTERED, DEFACED, OR REMOVED SERIAL NUMBERS VOID THIS ENTIRE WARRANTY
NO OTHER WARRANTIES
PIONEER DJ LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE WARRANTY PERIOD.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND SOME STATES DO NOT ALLOW THE EXCLUSIONS OR LIMITATIONS
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
TO OBTAIN SERVICE
PDJA has appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service you
need to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit you will need to package it
carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business
hours.
On all complaints and concerns in the U.S.A. and Canada call Customer Support at 1-800-872-4159.
For hook-up and operation of your unit or to locate an
Authorized Service Company, please call or write:
CUSTOMER SUPPORT
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1720
LONG BEACH, CALIFORNIA 90801
1-800-872-4159
http://www.pioneerelectronics.com
DISPUTE RESOLUTION
Following our response to any initial request to Customer Support, should a dispute arise between you and Pioneer DJ, Pioneer DJ makes available its Complaint Resolution
Program to resolve the dispute. The Complaint Resolution Program is available to you without charge. Yo u are required to use the Complaint Resolution Program before you exercise
any rights under, or seek any remedies, created by Title I of the Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-872-4159 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer DJ product was purchased. After the
complaint has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, Pioneer DJ will investigate the dispute
and will either: (1) respond to your complaint in writing informing you what action Pioneer DJ will take, and in what time period, to resolve the dispute; or (2) respond to your
complaint in writing informing you why it will not take any action.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____________________________________________ Serial No. _________________________________________ Purchase Date ______________________
Purchased From ____________________________________________________________________________________________________________________________
_
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE

To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA/Aux Etats-Unis or In Canada/Aux Canada
http://www.pioneerelectronics.com
S018_C1_EnFr_PSV
© 2016 Pioneer DJ Corporation.
All rights reserved.
Printed in <DRH1349-A>
PIONEER ELECTRONICS (THAILAND) CO., LTD.
17th Fl., KPN Tower, 719 Rama 9 Road, Bangkapi, Huaykwang, Bangkok 10310
TEL: [phone]
PIONEER TECHNOLOGY (MALAYSIA) SDN. BHD
16th Floor, Menara Uni. Asia 1008 Jalan Sultan Ismail 50250 Kuala Lumpur
TEL: [phone]
ӒᎣ޷ӌԥϵѨ
ѯᢋѯіҀϲ෺ୣ࿆ӏၰ ĵıĸ ဵĹዃTEL: [phone]
ӒᎣႬφȞ෬ȟԥϵѨ
෬Οᓹߞؔᢋၿ ĺıĺġဵ Ķġዃ TEL: [phone]
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec,
Mexico, D.F. 11000 TEL: [phone]
PIONEER INDIA ELECTRONICS PRIVATE LTD.
216, Second Floor, Time Tower, M.G. Road, Sector 28, Gurgaon 122001,
Haryana, India TEL: [phone]
PDJ_001_all
6F, Yo kohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yo kohama, Kanagawa 220-0012 JAPA N
〒220-0012神奈川県横浜市西区みなとみらい4丁目4番5号横浜アイマークプレイス6階
Корпорация Пайонир Диджей
6F, Йокогама i-Mark Place, 4-4-5 Минатомирай, Ниси-ку, Йокогама, Канагава 220-0012 ЯПОНИЯ
Anteros Building, Odyssey Business Park, West End Road,South Ruislip, Middlesex, HA4
6QQ, U.K.TEL: [phone]
2050 W. 190th Street, Suite 109, Torrance, CA 90504, U.S.A. TEL: [phone]
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
2 Jalan Kilang Barat, #07-01, Singapore 159346 TEL: [phone]
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: [phone]