Pioneer BDP-09FD - Elite Blu-Ray Disc Player User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION
2008
2008 Printed in Japan
BDP-09FD
RRV3865
Blu-ray Disc PLAYER
BDP-09FD
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement DVD
Region No.
BD
Region No. Remarks
BDP-09FD KU/CA AC 120 V 1 A
For details, refer to "Important Check Points for good servicing".
T-ZZY-001 DEC.

2BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
SAFETY INFORMATION
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely,
you should not risk tryingto do so and refer the repair to a qualified service technician.
WARNING
This product contains certain electrical parts contain chemicals which are known to the State of California to cause cancer,
birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIANMODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIENSEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.

3
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
LABEL CHECK
(Printed on the Rear Panel)
The following caution label appears on your unit.
Location: inside of the unit
WARNING !
THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATIONEXCEEDING THE LIMIT
FOR CLASS 1.
A SPECIALLY INSTRUCTED PERSONSHOULD DO SERVICING OPERATIONOF THE
APPARATUS.
Laser Pickup specifications and Laser characteristics
For BD Wave length : 405 nm
Operating output : 0.95 mW CW, Class 1M
Maximum output : Class 2 (under fault condition)
For DVD Wave length : 660 nm
Operating output : 1.06 mW CW, Class 1M
Maximum output : Class 2M (under fault condition)
For CD Wave length : 785 nm
Operating output : 1.34 mW CW, Class 1M
Maximum output : Class 1M (under fault condition)
VRW2262 - A

4BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
aSafe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

5
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS.................................................................................................................................................... 7
1.1 NOTES ON SOLDERING............................................................................................................................................... 7
1.2 NOTE ON DISASSEMBLING/REASSEMBLING............................................................................................................ 7
1.3 NOTE ON REPLACING IC9011 ..................................................................................................................................... 7
1.4 NOTE ON REPLACING THE TRAY PANEL BASE AND TRAY ALUMINUM ................................................................. 7
2. SPECIFICATIONS................................................................................................................................................................. 8
2.1 ACCESSORIES.............................................................................................................................................................. 8
2.2 SPECIFICATIONS .......................................................................................................................................................... 9
2.3 DISC/CONTENT FORMAT........................................................................................................................................... 10
2.4 PANEL FACILITIES....................................................................................................................................................... 14
3. BASIC ITEMS FOR SERVICE ............................................................................................................................................ 17
3.1 CHECK POINTS AFTER SERVICING ......................................................................................................................... 17
3.2 PCB LOCATIONS ......................................................................................................................................................... 18
3.3 JIGS LIST ..................................................................................................................................................................... 19
4. BLOCK DIAGRAM .............................................................................................................................................................. 20
4.1 OVERALL WIRING DIAGRAM ..................................................................................................................................... 20
4.2 BLOCK DIAGRAM........................................................................................................................................................ 22
4.3 POWER BLOCK DIAGRAM ......................................................................................................................................... 24
4.4 CLOCK BLOCK DIAGRAM........................................................................................................................................... 28
4.5 RESET BLOCK DIAGRAM........................................................................................................................................... 29
4.6 VIDEO BLOCK DIAGRAM............................................................................................................................................ 30
5. DIAGNOSIS ........................................................................................................................................................................ 31
5.1 POWER ON SEQUENCE............................................................................................................................................. 31
5.2 TROUBLE SHOOTING................................................................................................................................................. 32
5.3 RESET ON SEQUENCE .............................................................................................................................................. 33
6. SERVICE MODE................................................................................................................................................................. 34
6.1 OSD.............................................................................................................................................................................. 34
7. DISASSEMBLY ................................................................................................................................................................... 44
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 58
8.1 NECESSARY ADJUSTMENT POINTS ........................................................................................................................ 58
8.2 FIRMWARE UPDATE ................................................................................................................................................... 58
8.3 MODEL SETTING ........................................................................................................................................................59
8.4 CPRM ID NUMBER AND DATA SETTING ................................................................................................................... 61
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 64
9.1 PACKING SECTION ..................................................................................................................................................... 64
9.2 EXTERIOR SECTION .................................................................................................................................................. 66
9.3 BOTTOM SECTION...................................................................................................................................................... 68
9.4 FRONT PANEL SECTION ............................................................................................................................................ 70
10. SCHEMATIC DIAGRAM.................................................................................................................................................... 72
10.1 SERVICE MAIN ASSY (1/13)(GUIDE PAGE)............................................................................................................. 72
10.2 SERVICE MAIN ASSY (2/13)(GUIDE PAGE)............................................................................................................. 78
10.3 SERVICE MAIN ASSY (3/13) ..................................................................................................................................... 84
10.4 SERVICE MAIN ASSY (4/13) ..................................................................................................................................... 86
10.5 SERVICE MAIN ASSY (5/13) ..................................................................................................................................... 88
10.6 SERVICE MAIN ASSY (6/13) ..................................................................................................................................... 90
10.7 SERVICE MAIN ASSY (7/13)(GUIDE PAGE)............................................................................................................. 92
10.8 SERVICE MAIN ASSY (8/13) ..................................................................................................................................... 98
10.9 SERVICE MAIN ASSY (9/13) ................................................................................................................................... 100
10.10 SERVICE MAIN ASSY (10/13) ............................................................................................................................... 102
10.11 SERVICE MAIN ASSY (11/13) ............................................................................................................................... 104
10.12 SERVICE MAIN ASSY (12/13) ............................................................................................................................... 106
10.13 SERVICE MAIN ASSY (13/13) ............................................................................................................................... 108
10.14 SPATA ASSY........................................................................................................................................................... 110
10.15 AUPWASSY........................................................................................................................................................... 112
10.16 AUJB ASSY (1/5).................................................................................................................................................... 114
10.17 AUJB ASSY (2/5).................................................................................................................................................... 116
10.18 AUJB ASSY (3/5).................................................................................................................................................... 118
10.19 AUJB ASSY (4/5).................................................................................................................................................... 120
10.20 AUJB ASSY (5/5).................................................................................................................................................... 122
10.21 VOUT ASSY ........................................................................................................................................................... 124
10.22 FLKY ASSY ............................................................................................................................................................ 126
10.23 PSWB AND ACSWASSY ...................................................................................................................................... 128
10.24 SYPS ASSY............................................................................................................................................................ 130
10.25 WAVEFORMS......................................................................................................................................................... 132

6BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
11. PCB CONNECTION DIAGRAM ......................................................................................................................................134
11.1 SERVICE MAIN ASSY..............................................................................................................................................134
11.2 SPATA ASSY.............................................................................................................................................................138
11.3 VOUT ASSY..............................................................................................................................................................139
11.4 AUPWASSY.............................................................................................................................................................140
11.5 AUJB ASSY ..............................................................................................................................................................142
11.6 FLKY ASSY ..............................................................................................................................................................146
11.7 PSWB ASSY.............................................................................................................................................................148
11.8 ACSWASSY.............................................................................................................................................................150
11.9 SYPS ASSY..............................................................................................................................................................152
12. PCB PARTS LIST ............................................................................................................................................................154

7
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
1.2 NOTE ON DISASSEMBLING/REASSEMBLING
1.3 NOTE ON REPLACING IC9011
1.4 NOTE ON REPLACING THE TRAY PANEL BASE AND TRAY ALUMINUM
• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Do NOT use a soldering iron whose tip temperature cannot be controlled.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
• Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
• For improvement of audio quality, many special screws and acetate tapes are used in this unit. Be careful when
disassembling/reassembling this unit, and be sure to restore the unit to its original state.
• As IC9011 (ROM) on the SERVICE MAINAssy is fixed to the board with a special adhesive, it is not provided as a
service part. If replacement of IC9011 (ROM) is required, replace the entire SERVICE MAINAssy.
• As the tray aluminum (VAH1467) and the tray panel base (VNK6455) are strongly adhered with double-back tape,
replace both parts when either needs to be replaced.
For attachment, adhere the tray aluminum (VAH1467) so that it is placed at the center of the tray panel base (VNK6455).
Tray aluminum
(VAH1467)
Tray panel base
(VNK6455)
Adhere the sheet at the center.

8BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
2. SPECIFICATIONS
2.1 ACCESSORIES
Remote control x 1
(VXX3316)
Operating instructions
(VRB1508)
BNC-RCA adapter x 3
(AKX1052)
Use this to connect an RCA pin type
cable to the COMPONENT VIDEO
terminal.
Audio cable (white/red) x 1
(VDE1064) L=1.5 m
Video cable (yellow) x 1
(VDE1065) L=1.5 m
AA/R6 dry cell batteries x 2
LANcable x 1
(VDE1098)
Power cord x 1
(ADG7061)
Warranty card

9
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
2.2 SPECIFICATIONS
Model BDP-09FD
Type Blu-ray Disc PLAYER
Rated voltage AC 120 V
Rated frequency 60 Hz
Power consumption 58W
Power consumption (standby) 0.3 W
Weight 14.3 kg (31 lb 9 oz)
External dimensions (inc luding projecting parts) 420 mm (W) x 143 mm (H) x 365 mm (D)
(16
9/16 in. (W) x 5 11/16 in. (H) x 14 6/16 in. (D))
Tolerable operating temperature +5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity 5 % to 85 % (no condensation)
Output terminals
HDMI 2 sets, 19-pin: 5 V, 250 mA (Total value for the HDMI OUT
(MAIN) and HDMI OUT (SUB) terminals)
Video outputs Video 1 set, RCA jack: 1.0 Vp-p (75 Ω)
S-Video 1 set, S-Video jack:
Y (luminance): 1.0 Vp-p (75 Ω)
C (color): 0.286 Vp-p (75 Ω)
Component video 1 set, BNC jacks:
Y: 1.0 Vp-p (75 Ω)
PB, PR: 0.7 Vp-p (75 Ω)
Audio outputs 7.1-channel (multi-channel: front left/
right, surround left/right, center,
surround back left/right, subwoofer)
1 set, Number of channels: 8, RCA jacks
Audio output level 200 mVrms (1 kHz, –20 dB)
Frequency response 4 Hz to 88 kHz (192 kHz sampling)
S/Nratio 115 dB
Dynamic range 103 dB
Total harmonic distortion 0.0015 %
Wow & flutter Below measurable limits (±0.001 % W. PEAK)
Digital audio outputs Optical 1 set, Optical digital jack
Coaxial 1 set, RCA jack
LAN1 set, Ethernet jack (100BASE-TX)
Control Input 1 set, Minijack (3.5 ø)
Note
• The specifications and design of this product are subject to change without notice.
• This product includes FontAvenue
®
fonts licensed by NEC Corporation.
FontAvenue is a registered trademark of NEC Corporation.

10 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
2.3 DISC/CONTENT FORMAT
[1] Playable discs
Discs with the logo marks below indicated on the disc label, package or jacket can be played.
“Blu-ray Disc” and are trademarks.
is a trademark of DVD Format/Logo Licensing Corporation.
Disc type
Logo Application format
BDMV1
1. Including the AVCHD format.
BDAVDVD-Video DVD VRCD-DA
DTS-CD DATA-DISC2
2. Discs on which video, image or audio files are recorded
BD
BD-ROM
BD-R
BD-RE
DVD
DVD-ROM
DVD-R
DVD-R DL
(Dual Layer)
DVD-RW
DVD+R
DVD+RW
CD
CD-DA
(Audio CD)
CD-R
CD-RW
CD-ROM

11
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
Discs that cannot be played
•Non-finalized (Non-closed) BD-R discs in the BDMVformat
•HDDVDs
•DVD Audio discs
•DVD-RAM discs
•
Non-finalized DVD-R/-RW/+R/+RW discs in the DVD-Video
format and AVCHD format
•Non-finalized Dual Layer DVD-R discs in the DVD VR format
•Non-finalized CD-R/-RW discs
• SACDs
•Video CDs
•SVCDs
This player conforms to NTSC standards. Discs for which “NTSC” is
indicated on the disc label, package or jacket can be played.
Note
•
Some discs cannot be played, even if one of the logo marks on
the previous page is indicated.
• To play 8cm discs, set the disc in the 8cm disc depression in
the center of the disc tray. No adapter is necessary. 8cm BD-
ROMs cannot be played.
About audio formats
The following audio formats are supported on this player:
• Dolby TrueHD
• Dolby Digital Plus
• Dolby Digital
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
•MPEG
• MPEG-2 AAC
• Linear PCM
To enjoy the surround sound of Dolby TrueHD, Dolby Digital Plus,
DTS-HD Master Audio and DTS-HD High Resolution Audio, it is
recommended to connect the player to an AVreceiver or amplifier
compatible with these audio formats using an HDMI cable. After
loading a BD containing sound in one of these audio formats, select
the audio format on the menu screen.
Manufactured under license from Dolby Laboratories. Dolby and the
double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide
patents issued & pending. DTS is a registered trademark and the DTS
logos, Symbol, DTS-HD and DTS-HD Advanced Digital Out are
trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
PlayingBDs
• BDs (BDMV) compatible with the formats below can be played.
– Blu-ray Disc Read-Only (ROM) Format Version 2
– Blu-ray Disc Recordable (R) Format Version 2 (finalize (close)
them before playing them on this player)
– Blu-ray Disc Rewritable (RE) Format Version 3
This player supports BD-ROM Profile 1 Version 1.1.
BONUSVIEW Functions such as playback of secondary video
(Picture-in-Picture) and secondary audio can be used. For
details on secondary video and secondary audio playback, refer
to the disc’s instructions.
“BONUSVIEW” is trademark of Blu-ray Disc Association.
When a BD-ROM is played, additional data may be stored in the
player’s memory area (local storage). If the message indicating
low memory (local storage) appears, erase the BDMVdata.
• BDs (BDAV) compatible with the formats below can be played.
– Blu-ray Disc Recordable (R) Format Version 1
– Blu-ray Disc Rewritable (RE) Format Version 2
• Dual Layer BDs can be played.
•Video, image and audio files recorded on BDs cannot be played.
•8cm BD-ROMs cannot be played.
PlayingDVDs
•DVD-Video can be played.
•
DVD-R/-RW/+R/+RW discs recorded in the DVD-Video format
can be played (finalize them before playing them on this player).
•
DVD-R/-RW discs recorded in the VR format (Video Recording
format) can be played.
This label indicates playback compatibility with DVD-RW discs
recorded in VR format (Video Recording format). However, for discs
recorded with a record-only-once encrypted program, playback can
only be achieved using a CPRM compatible device.

12 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
•DVDs recorded in the AVCHD format can be played (finalize
them before playing them on this player).
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic
Corporation and Sony Corporation.
•Video, image and audio files recorded on DVD-R/-RW/+R/+RW
discs can be played. See Playable files below.
• Dual Layer DVDs can be played. However, non-finalized Dual
Layer DVD-R discs recorded in the VR format cannot be played
(finalize them before playing them on this player).
• HD DVD, DVD Audio and DVD-RAM discs cannot be played.
About region numbers
Blu-ray Disc Player and BD-ROM or DVD-Video discs are assigned
region numbers according to the region in which they are sold.
This player’s region numbers are:
• BD-ROM: A
•DVD-Video: 1
Discs not including these numbers cannot be played. Discs
playable on this player are as shown below.
• BDs: A (including A) and ALL
•DVDs: 1 (including 1) and ALL
PlayingCDs
• Audio CDs (CD-DAs and DTS-CDs) can be played.
•Video, image and audio files recorded on CDs can be played.
See Playable files below.
• CD-R/-RW discs that are not finalized cannot be played.
• SACD, Video CD and Super VCD discs cannot be played.
• Regarding copy protected CDs: This player is designed to
conform to the specifications of the Audio CD format. This
player does not support the playback or function of discs that do
not conform to these specifications.
DualDisc playback
A DualDisc is a new two-sided disc, one side of which contains DVD
content — video, audio, etc. — while the other side contains non-
DVD content such as digital audio material.
The DVD side of a DualDisc can be played on this player (excluding
any DVD-Audio content).
The non-DVD, audio side of the disc is not compatible with this
player.
It is possible that when loading or ejecting a DualDisc, the opposite
side to that being played will be scratched. Scratched discs may not
be playable.
For more detailed information on the DualDisc specification, please
refer to the disc manufacturer or disc retailer.
Playingdiscs created on computers or BD/
DVD recorders
• It may not be possible to play discs recorded using a computer
due to the application settings or computer’s environment
settings. Record discs in a format playable on this player. For
details, contact the dealer.
• It may not be possible to play discs recorded using a computer
or a BD/DVD recorder, if burn quality is not good due to
characteristics of the disc, scratches, dirt on the disc, dirt on the
recorder’s lens, etc.
[2] Playable files
Video, image and audio files recorded on DVDs and CDs can be
played.
Caution
•InDVD, only the one recorded by the ISO 9660 file system can be
played.
• Some files may not be playable.
•For some files, it may not be possible to use certain functions
during playback.
•It may not be possible to play some files, even if they have the
extension of a file playable on this player.
• Files protected by DRM (Digital Rights Management) cannot be
played (not including DivX VOD files).
Supported video file formats
•DivX
DivX is a media technology created by DivX, Inc. DivX media files
contain not only video but also advanced media features like
subtitles and alternate audiotracks, etc.
Conform to the size under 720 x 480 pixels.
DivX files encoded with GMC/Qpel option cannot be played.
Only audio signals with MP3 or Dolby Digital (AC3) format are
output.
Note that files other than the ones containing DivX video cannot
be played, even if they have the extension “.avi”.
®
Official DivX Certified product.
®®
Plays all versions of DivX video (including DivX 6) with standard
®
playback of DivX media files.
DivX, DivX Certified, and associated logos are trademarks of DivX,
Inc. and are used under license.

13
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
Note
• DivX VOD files are protected by DRM. They can only be played
on registered devices.
–You may be requested by the file distributor to input the DivX
VOD registration code for authorization of the player in order
to play DivX VOD files. This player’s DivX VOD registration
code can be checked at Initial Setup Playback DivX
VOD Registration Code.
–DivX VOD files for which the player’s DivX VOD registration
code is not authorized cannot be played (Authorization
Error is displayed).
– The number of views is restricted for some DivX VOD files.
When such files are played on this player, the remaining
number of views is displayed. Files for which the remaining
number of views has reached 0 cannot be played (Rental
Expired is displayed). Files for which the number of views is
not restricted can be played as many times as you like (the
remaining number of views is not displayed).
Supported image file formats
•JPEG
File format: JFIF Ver1.02/Exif Ver.2.2
Resolution: Up to 4096 x 4096 pixels
Only baseline JPEG files are supported.
Supported audio file formats
•Windows Media™ Audio 9 (WMA9)
Bit rate: Up to 192 kbps
Sampling frequencies: 22.05 kHz, 32 kHz, 44.1 kHz and 48kHz
Windows Media is either a registered trademark or trademark of
Microsoft Corporation in the United States and/or other countries.
This product includes technology owned by Microsoft Corporation
and cannot be used or distributed without a license from
Microsoft Licensing, Inc.
•MPEG-1 Audio Layer 3 (MP3)
Bit rate: Up to 320 kbps
Sampling frequencies: 8kHz, 11.025 kHz, 12 kHz, 16 kHz,
22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and 48kHz
Playable file extensions
•Video files
.divx and .avi
•Image files
.jpg and .jpeg
•Audio files
.wma and .mp3

14 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
2.4 PANEL FACILITIES
[1] Front Panel
1 STANDBY/ON
Press to turn the power on and off.
2 PURE AUDIO – High quality audio signals with any extraneous
noise eliminated are output.
RESOLUTION – Press to switch the output video resolution from
HDMI OUT or COMPONENT VIDEO output terminals.
3 Front panel display
4 Remote control sensor
Point the remote control to this, then operate it within approximately
23 feet.
The player may have trouble capturing remote control signals if
there is a fluorescent light nearby. If this happens, move the player
away from the fluorescent light.
5 OPEN/CLOSE – Press to open and close the disc tray.
/– Press to skip to the beginning of the previous title/
chapter/track/file. Press and hold to start reverse scanning.
/– Press to skip to the beginning of the next title/
chapter/track/file. Press and hold to start forward scanning.
– Press during playback to pause. Press again to restart
playback.
– Press to stop playback.
6
Press to start playback.
7 HDMI indicator
This lights when an HDMI-compatible device is connected to an
HDMI OUT (MAIN) or HDMI OUT (SUB) terminal.
8FL OFF indicator
This lights when Off is selected with FL DIMMER.
9 Disc tray
10 HD indicator
This lights when an HDMI cable is connected and video signals are
being output with a resolution of 1080/24p, 1080/60i, 1080/60p or
720/60p. It also lights when a component video cable is connected
and video signals are being output with a resolution of 1080/60i or
720/60p.
11 PURE AUDIO indicator
This lights when PURE AUDIO is set to Mode 1 or Mode 2.

15
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
[2] Remote Control
1 STANDBY/ON
Press to turn the power on and off.
2 TV CONTROL
Your TVcan be controlled using the player’s remote control.
– Press to turn the TV’s power on and off.
INPUT SELECT – Press to switch the TV’s input.
CH +/– – Press to select the TVchannel.
VOL +/– – Press to adjust the volume.
3 AUDIO
Press to switch the audio streams/channels.
4 SUBTITLE
Press to switch the subtitles.
5 Number buttons – Use these to select and play the title/
chapter/track you want to view or listen to and to select items
from menus.
CLEAR – Press to clear the numeric number, etc.
ENTER – Press to execute the selected item or enter a setting
that has been changed, etc.
6 SECONDARY AUDIO – When playing a BD-ROM on which
secondary audio is recorded, press to switch to the secondary
audio.
SECONDARY VIDEO – When playing a BD-ROM on which
secondary video (Picture-in-Picture) is recorded, press to switch
to the secondary video.
7 VIDEO SELECT
Press to switch the video output signal to be viewed between the one
output from the HDMI OUT (MAIN) terminal, the HDMI OUT (SUB)
terminal and an analog output terminal (COMPONENT VIDEO, S-
VIDEO or VIDEO output terminals).
8HOME MEDIA GALLERY
Press to display/hide the Home Media Gallery screen.
9TOPMENU
Press to display the top menu of the BD-ROM or DVD-Video.
10 / / / – Use to select items, change settings and move
the cursor.
ENTER – Press to execute the selected item or enter a setting
that has been changed, etc.
11 HOME MENU
Press to display/hide the Home Menu.
12 PLAY – Press to start playback.
PAUSE – Press to pause playback. Press again to restart
playback.
STOP – Press to stop playback.
PREV/ NEXT – Press to skip to the beginning of the
previous/next title/chapter/track/file.
//– Press during playback to start reverse scanning.
While playback is paused, press for step reverse playback. Press
and hold while playback is paused for reverse slow motion
playback.
// – Press during playback to start forward scanning.
While playback is paused, press for step forward playback.
Press and hold while playback is paused for forward slow
motion playback.
13 RED/GREEN/BLUE/YELLOW
Use these to navigate BD-ROM menus.
14 VIDEO ADJUST
Press to display/hide the Video Adjust menu.
15 OPEN/CLOSE
Press to open and close the disc tray.
16 FL DIMMER
Press to switch the brightness of the front panel display.
The FL OFF indicator lights when Off is selected.
17 ANGLE
Press to switch the BD-ROM or DVD-Video camera angles.
18OUTPUT RESOLUTION
Use these to switch the output video resolution from the HDMI OUT
or COMPONENT VIDEO output terminals.
19 PLAY MODE
Press to display/hide the Play Mode screen.
20 POP UP MENU/MENU
Press to display the BD-ROM or DVD-Video menus.
21 DISPLAY
Press to display disc information.
22 TOOLS
Press to display/hide the TOOLS menu.
23 RETURN
Press to return to the previous screen.

16 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
[3] Front Panel Display
1
Lights during playback.
2
Lights when playback is paused.
3LAN
Lights when there is an active local area network (LAN) connection.
4PQLS
Lights when the PQLS function is activated.
5 Character display
Displays the title/chapter/track number, elapsed time, etc.
6 24HZ/50HZ/60HZ
The frequency of the video frame or field being output lights.
7CONTROL
Lights when the KURO LINK function is activated.
8HDMI 1 2
HDMI 1 lights when VIDEO SELECT is pressed and the HDMI OUT
(MAIN) terminal is selected. HDMI 2 lights when the HDMI OUT
(SUB) terminal is selected.
[4] Rear Panel
1 AUDIO OUT (7.1 ch) terminals
Connect with the multi-channel (7.1- or 5.1-channel) audio input
terminals on an AVreceiver or amplifier, etc..
To connect to the 2-channel audio input terminals on a TV, etc.,
connect to FRONT (L/R).
2 AC IN
Connect the power cord here.
3 VIDEO OUT terminals
VIDEO – Connect with the video input terminal on a TV, AV
receiver or amplifier, etc..
S-VIDEO – Connect with the S-Video input terminal on a TV, AV
receiver or amplifier, etc..
COMPONENT VIDEO (BNC jacks) – Connect with the
component video input terminals on a TV, AVreceiver or
amplifier, etc..
4 RS-232C terminal
This terminal is not used.
5 HDMI OUT terminals
MAIN (KURO LINK) – Connect with an HDMI-compatible TV, AV
receiver or amplifier, etc..
SUB – Connect with an HDMI-compatible TV, projector, etc..
This terminal outputs linear PCM 2-channel audio signals.
Do not connect an AVreceiver or amplifier to this terminal.
Also note that the KURO LINK function will not work for
devices connected to this terminal.
6 DIGITAL OUT (COAXIAL/OPTICAL) terminals
Connect with the digital audio input terminal on an AVreceiver or
amplifier, etc..
7 LAN (100) terminal
Ethernet port for 100BASE-TX (100 Mbps) network connection.
8CONTROL IN terminal
Use to control this player from the remote sensor of another Pioneer
component with a CONTROL OUT terminal and bearing the
mark. Connect the CONTROL OUT terminal of the other component
to CONTROL IN on this player using a mini-plug cord (commercially
available).
Caution
• Be sure to connect cables for outputting the audio and video
signals.
• When connected via System Control, point the remote control
toward the connected component (such as an AVreceiver or
amplifier). The remote will not work correctly when pointed at
this player.
• You cannot use System Control with components that do not
have a System Control terminal or with components
manufactured by companies other than Pioneer.

17
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
Items to be checked after repair (BD players)
To ensure the quality of the product after repair, check the recommended items shown below:
See the table below for the items to be checked regarding video and audio:
* (ex.) SC-LX81, SC-LX71.
Item to be checked regardingvideo Item to be checked regardingaudio
Block noise Distortion
Horizontal noise Noise
Dot noise Volume too low
Disturbed image (video jumpiness) Volume too high
Too dark Volume fluctuating
Too bright Sound interrupted
Mottled color
Color disappearance
No. Procedures Item to be checked
1 Check the version of the firmware in Service mode. The version must be the latest.
If the version is not the latest, update the firmware.
2
Check if all the symptoms pointed out by the customer have been
addressed. If a symptom pointed out by the customer is
attributable to a particular disc, that disc must be played back.
The symptoms in question must not be reproduced.
Video, audio, and operations must be normal.
3
Measure playback error rates at the innermost and outermost
tracks, by playing back the following discs:
BD-ROM test disc (GGV1308)
DVD test disc (GGV1025)
If the symptoms are related to the PQLS (Precision Quartz Lock
System), check PQLS operations.
(For checking PQLS operations, connection with an amplifier*
that supports the PQLS is required.)
The error rates must be 1.0e-3 or less.
This procedure can determine if the drive is degraded.
For checking PQLS operations, connect the player with the
customer’s amplifier then check that “PQLS” is lit in the display
window on the unit. (See [3] Front Panel Display in
“2.4 PANEL FACILITIES.”)
4 Check playback of a CD disc (track search). Audio and operations, such as a search, must be normal.
5Check playback of a DVD disc (menu operations, title/chapter
search). Video, audio, and operations, such as a search, must be normal.
6Check playback of a BD disc (menu operations, title/chapter
search). Video, audio, and operations, such as a search, must be normal.
7 Check the cabinet. Check for any scratches or dirt that have been made or attached
on the cabinet after receiving the product for repair.
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:
Position to be cleaned Cleaningtools
Pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
Position to be cleaned Cleaningtools
Fans Cleaning paper : GED-008
Cleaning

18 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
3.2 PCB LOCATIONS
NSP 1..FLKB ASSY VWM2482
2..FLKY ASSY VWG2626
2..PSWB ASSY VWG2627
NSP 1..AVJB ASSY VWM2483
2..AUJB ASSY VWG2630
2..VOUT ASSY VWV2381
NSP 1..AUPB ASSY VWM2484
2..AUPW ASSY VWG2628
2..ACSW ASSY VWG2629
1..SERVICE MAINASSY VXX3348
NSP 2..MAINASSY VWV2382
2..SPATA ASSY VWV2387
>1..SYPS ASSY VWR1422
1..BD/DVD/CD DRIVE
VXX3343
(BDR-L04H-XA/XV/5)
GPSWB Assy FFLKY Assy
CAUPW Assy
ISYPS Assy BD/DVD/CD DRIVE
HACSW Assy DAUJB Assy
E
VOUT Assy BSPATA Assy
ASERVICE MAINAssy
NOTES:
-
Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
-
The >mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES

19
BDP-09FD
56 7 8
56 7 8
A
B
C
D
E
F
3.3 JIGS LIST
Service Remote Control Unit GGF1067
DVD Test Disc (DVD-Video)
BD-ROM Test Disc
GGV1334
Adjustment, diagnosis
Name JigNo. Remarks
Check of DVD-Video
Check of BD-ROM
ID Data Disc for Blu-ray player
GGV1025
GGV1308
Diagnosis (ID data setting)
Jigs List
Disc Ejection Rod GGF1529 Emergency Disc Ejection

20 BDP-09FD
12 3 4
A
B
C
D
E
F
12 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
HVOL_DET
GND
V+5E
XAMUTE
GND
XDACRST
GND
GND
ML1
ML2
MC
MD
GND
MCLK
GND
LRCK
GND
BCK
GND
ADATA3
GND
ADATA2
GND
ADATA1
GND
ADATA0
GND
GND
LED_FL_OFF
V+3R3D
GND GND
FANCTL_SW1
LED_PON
IR
KEY1
GND
V+5E
KEY0
GND
LED_A_MODE
FLSTRB
GND
FLCLK
LED_HD
LED_HDMI
GND GND
LED_BLUE
GND GND
FANCTL_SW2
V+3R3SE
GND
FLDATA
GND GND
GND
GND
V+5E
GND
XAMUTE
GND
XDACRST
GND
GND
ML1
ML2
MC
MD
GND
MCLK
GND
LRCK
GND
BCK
GND
ADATA3
GND
ADATA2
GND
ADATA1
GND
ADATA0
GND
GNDS
UREG-17V UREG-17V UREG-17V
GNDA GNDA GNDA
UREG17V UREG17V UREG17V
GNDA GNDA GNDA
UREG17V_DAC UREG17V_DAC UREG17V_DAC
GNDA GNDA GNDA
GNDD GNDD
UREG+5V UREG+5V UREG+5V UREG+5V
GNDD GNDD
AUDIO_CT
AUDIO_1
AUDIO_2
DIGTAL1
DIGTAL2
GND
LED_PON
KEY0
V+12
GND_LED
GND_LED
GND_FL
V-23
GND_FL
FLDC+
FLDC-
GND
V+5E
GND
V+3R3E
GND
232C_CTS 232C_RTS
232C_Tx
232C_Rx
GND
V+5AD_V
V_MUTE
LETTER
SQUEESE
GND
A_VYOUT_DAC
GND
A_VCOUT_DAC
GND
A_VVOUT_DAC
CN4201
VKN1413-
1
2
3
4
5
6
7
8
9
CN1301
VKN2048-
1
2 3 4
5
6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
CN1001
CKS-556
1
2 3
CN1301
CKS-555
1
2
CN2000
VKN1610-
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
CN6001
VKN1610-
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
CN8901
VKN1618-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN1402
VKN1618-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
CN1401
VKN2008- (B TO B)
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
27
13
CN901
VKN2011- (B TO B)
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
27
13
CN1002
VKN2008- (B TO B)
1 2 3 4 5 6 7 8 9
10 11 12 14 15 16 17 18 19 20 21 22 23 24 25
26 27 13
CN1001
VKN2011- (B TO B)
1
2 3 4 5
6
7 8 9
10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 13
CN101
VKN1290-
1 2 3 4
5
6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
CN102
AKM1359- (B TO B)
1
2
3
4
5
6
7
8
9
10
11
CN301
AKP1299- (B TO B)
1
2
3
4
5
6
7
8
9
10
11
VKN1322-A
CN4402
1 2 3 4 5 6 7 8 9
10
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
29 30
SBRFR
7.1ch
Optical
AUDIO OUT
JA4351
DIGITAL
SR IN
SH_ICE (NO USE)
GND
GND
V+3R3D
AUDCK
AUDATA0
M32TMS
M32TDI
M32TDO
M32TCK
GND
V+5E
TXD_PCON
RXD_PCON
GND
DBGP2
DBGP1
DBGP0
XDBG_RST
Sub- com Debug
RKN1004
VDA2193-
V+3R3D
NC
M32TRST_N
GND
AUDATA1
GND
AUDATA2
GND
AUDATA3
GND
AUDSYNC
GND
SH_TCK
SH_TMS
GND
SH_TRST_N
MPMD
SH_TDI
SH_TDO
ASEBRKAL_N
RESET_N
JA101
SD CARD
DKP3748-A
JA3701
VDA2194-
SUB TRANS
FL LFE C SR SL SBL
JA201 JA301 JA401 JA501 JA601 JA701 JA801
LAN
RS-232C
VDA2204-
AKB7102
JA2100
JA2101
AKP1239
JA2300
AKP1213
S-VIDEO COMPOSITE
VKN2087
JA4501
JA8002
VKS1002
VWX1234-A
AKB7102 x8
(NO USE)
FLUORESCENT TUBE
Remote receiver
VTT1173-
D
AUJB ASSY
( 1/5- 5/5)
(VWG2630)
C
AUPW ASSY
(VWG2628)
F
FLKY ASSY
(VWG2626)
E
VOUT ASSY
(VWV2381)
D D
!